Kia EV6: High Voltage System General Safety Information and Caution / Precautions for accident vehicle

Precautions for accident vehicle
Warning
Electric vehicle includes a high voltage battery, which can lead to serious accidents such as short circuits or electric shocks if touched incorrectly. Be sure to observe all of the following below.
Preparations when servicing the accident vehicle
1.
Personal Protective Equipment (PPE)
(Refer to High Voltage System General Safety Information and Caution - "Personal Protective Equipment (PPE)")
2.
Boric Acid Power or Solution
3.
ABC Extinguisher
4.
Towel for cleaning electrolyte
5.
Fire blacket
6.
Vinyl tape (for insulating terminal)
7.
Mega ohm tester (for checking high voltage)
Precautions when handling the vehicle after an accident
1.
Before handling an accident vehicle, the technician has to wear Personal Protective Equipment (PPE).
(Refer to High Voltage System General Safety Information and Caution - "Personal Protective Equipment (PPE)")
2.
Never touch the power cable from which the insulating coating has been peeled off.
3.
Since the gas is hydrogen and alkaline vapor, immediately ventilate the room and evacuate to a safe place.
4.
If the leaked liquid comes in contact with skin, immediately neutralize the affected area with boric acid solution, then cleanse with tap water or salt water.
5.
Refer to "High voltage shut-off procedure" if the high voltage needs to be shut off.
(Refer to Battery Control System (Long Range) - "High Voltage Shut-off Procedures")
6.
After an accident, check the high voltage battery sensor data (insulation resistance, voltage deviation between cells, DTCs, etc.) and internal damage.
7.
When replacing the high voltage battery with a fine deformation, only the case is exchanged after checking the change in the high voltage battery sensor data.
8.
Determine the type of accident and the your vehicle repaired as follows.
(1)
Electrical Accidents
•
Over charging/discharging : Displays a battery over voltage (P0DE700) code / low voltage (P0DE600) code (Refer to the DTC diagnosis guide)
•
Short circuit : Displays a code related to high voltage fuse short (P1B7700, P1B2500) (Refer to the DTC diagnosis guide)
(2)
Fire Accidents
Item
Inspection Procedure
Inspection Results
Correction
Fire except the high voltage battery installing area
(Example : fire in PE room)
1. Exterior inspection (deformation, corrosion, wire coating, odor, connector)
High voltage battery damaged
Insulation/insulation packaging after removing the high voltage battery
2. Measure the high voltage battery chassis insulation resistance after shutting off the high voltage
(Refer to Battery Control System - "Battery System Assembly (BSA)" )
High voltage battery insulation breakdown
3. Check for high voltage battery main fuse open circuit
(Refer to Battery Control System - "Main Fuse")
Main fuse open circuit
Replace the main fuse
4. Check the welding the high voltage battery main relay
(Refer to High Voltage Battery Control System - "Power Relay Assembly (PRA)")
Main relay welded
Power Relay Assembly (PRA) replacement
5. Check fault for other parts
Other parts fault
Replace the other parts
6. Check the DTC code of the Battery Management Unit (BMU)
DTC occurrence
Perform the DTC diagnostic guide repair procedures
Fire in the high voltage battery is installing area
1. Exterior inspection (deformation, corrosion, wire coating, odor, connector)
High voltage battery damaged
Insulation/insulation packaging after removing the high voltage battery
2. Check for external damage of the high voltage battery
External damage of high voltage battery (Heat marks, soot, etc)
Perform the battery disposal procedure after removing the high voltage battery
3. Measure the high voltage battery chassis insulation resistance after shutting off the high voltage
(Refer to Battery Control System - "Battery System Assembly (BSA)" )
High voltage battery insulation breakdown
Insulation/insulation packaging after removing the high voltage battery
4. Check for high voltage battery main fuse open circuit
(Refer to Battery Control System - "Main Fuse")
Main fuse open circuit
Replace the main fuse
5. Check the welding the high voltage battery main relay
(Refer to High Voltage Battery Control System - "Power Relay Assembly (PRA)")
Main relay welded
Power Relay Assembly (PRA) replacement
5. Check fault for other parts
Other parts fault
Replace the other parts
7. Check the DTC code of the Battery Management Unit (BMU)
DTC occurrence
Perform the DTC diagnostic guide repair procedures

(3)
Collision accidents
Inspection Procedure
Inspection Results
Correction
1. Exterior inspection (deformation, corrosion, wire coating, odor, connector)
High voltage battery damaged
Insulation/insulation packaging after removing the high voltage battery
2. Measure the high voltage battery chassis insulation resistance after shutting off the high voltage
(Refer to Battery Control Syste - "Battery System Assembly (BSA)" )
High voltage battery insulation breakdown
3. Check for high voltage battery main fuse open circuit
(Refer to Battery Control System - "Main Fuse")
Main fuse open circuit
Replace the main fuse
4. Check the welding the high voltage battery main relay
(Refer to High Voltage Battery Control System - "Power Relay Assembly (PRA)")
Main relay welded
Power Relay Assembly (PRA) replacement
5. Check fault for other parts
Other parts fault
Replace the other parts
6. Check the DTC code of the Battery Management Unit (BMU)
DTC occurrence
Perform the DTC diagnostic guide repair procedures

Information
•
If the high-voltage battery mounting area is inaccessible due to damage to the trunk and vehicle door, be sure not to damage the high voltage battery when deforming and cutting the exterior of the vehicle to perform the inspection and repair procedure.
•
Do not replace the high voltage battery when DTC does not occur or the external of battery is normal. (However, if the vehicle is damaged to the level of a scrapped car, perform the high-voltage battery disposal procedure.)
(4)
Flood accident
•
If more than half of the vehicle is submerged, then do not go near the high voltage service interlock connector or other high voltage related components. Even though it is inevitable, move the vehicle to safe area before taking actions.
•
Be Insulate and packing after removing the high voltage battery.

Other information:

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Special driving conditions

During poor weather, slippery roads, or difficult driving environments, the Kia EV6 should always be operated with increased caution, reduced speed, and greater attention than under normal driving conditions. Hazardous driving conditions When driving the Kia EV6 through water, snow, ice, mud, sand, gravel, or other hazardous road conditions, follow these important driving recommendations to improve safety and maintain vehicle stability: Drive carefully and always leave additional braking distance between the Kia EV6 and surrounding vehicles.

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Switching between panels

Figure 1. Infotainment control panel Figure 2. Climate control panel Press the Kia EV6 switchable controller button to activate the desired control panel mode. The selected Kia EV6 control panel icon illuminates and the controller switches to the chosen operating mode.

Categories

 
Copyright © 2026 Kia EV6 Manuals � 0.0269