Kia EV6: Chassis / Brake Fluid Repair procedures

Inspection
1.
Check the brake fluid level.
Caution
Be careful as brake fluid can hurt your hands and eyes and damage painted surfaces. If fluid gets on your hands or in your eyes, flush the affected area with clean water immediately.
Item
Recommended
Capacity
Brake fluid (cc)
DOT 4
As required
(339 - 379 cc)
*Refer to 'MAX - MIN" line on the reservoir tank
Brake pedal bushing and brake pedal bolt
Chassis grease
(GREASE PDLV-1)
As required

Integrated Electronic Brake (IEB) System Air Bleeding procedures
Special Serivce Tool
Tool Name / Number
Illustration
Description
Air bleeding tool
0K580 - 3D100

Maintenance — Chassis / Brake Fluid / Repair procedures / Inspection illustration

Used for brake bleeding (regulating pressure)
(Used with 0K585 - E8100)
Air bleeding tool adaptor
0K585 - E8100

Maintenance — Chassis / Brake Fluid / Repair procedures / Inspection illustration

Used for brake bleeding (reservoir cap adapter)
(Used with 0K580 - 3D100)

Note
•
Do not reuse the drained brake fluid.
•
Always use genuine DOT4 brake Fluid, Using a non-genuine DOT4 brake fluid can cause corrosion and decrease the life of the system.
•
Before opening the reservoir tank cap, clean any debris or material around.
•
Make sure that no dirt or other foreign matter is allowed to contaminate the brake fluid.
•
Be careful not to get brake fluid on the body or vehicle and, if so, wipe immediately with a clean cloth.
•
Fill the brake fluid during air bleeding to prevent the brake fluid level from falling below the 'MIN' line.
•
Close the SST's air shut-off valve first before opening the brake reservoir cap to fill the brake fluid.
1.
Disconnect the battery negative ( - ) terminal and the service interlock connector.
(Refer to Battery Control System - "Auxiliary 12 V Battery - 2WD")
(Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
2.
Close the air shut-off valve (A) and install the plug (B) before installing the SST (09580 - 3D100).

Maintenance — Chassis / Brake Fluid / Repair procedures / Inspection illustration

Note
•
Make sure that the plug (B) is securely installed for accurate setting of the pressure regulator and safety.
•
To avoid damaging the brake reservoir, and to ensure safety, set the pressure regulator (B) to 2 - 3 bar.
3.
Connect the air hose (A), and open the air shut-off valve slowly to set the pressure gauge (B) to specified value.

Pressure : 2 - 3 bar

Maintenance — Chassis / Brake Fluid / Repair procedures / Inspection illustration

4.
Close the air shut-off valve (A), and then remove the plug (B).

Maintenance — Chassis / Brake Fluid / Repair procedures / Inspection illustration

Caution
If the plug (B) removed while the air shut-off valve (A) is open, the injury can occur by hose.
5.
Remove the brake reservoir cap (A).

Maintenance — Chassis / Brake Fluid / Repair procedures / Inspection illustration

6.
Fill the brake fluid to the 'MAX' line.

Specification : DOT 4
Capacity : As required [About (339 - 379 cc)]

7.
Install the SST (0K585 - E8100) to the reservoir tank.

Maintenance — Chassis / Brake Fluid / Repair procedures / Inspection illustration

8.
Install the SST (09580 - 3D100) to the adapter.

Maintenance — Chassis / Brake Fluid / Repair procedures / Inspection illustration

9.
Install the air hose (A) to the SST (09580 - 3D100), and then pressurize to the specified pressure.

Specification : 2 - 3 bar

Maintenance — Chassis / Brake Fluid / Repair procedures / Inspection illustration

10.
Open each brake bleed screw (A), drain the brake fluid for about 15 seconds, then press the brake pedal 10 - 20 times and then close the bleed screw.

Tightening torque :
Front : 6.9 - 12.7 N·m (0.7 - 1.3 kgf·m, 5.1 - 9.4 lb·ft, 60.8 - 112.8 lb·in)
Rear : 13.7 - 19.6 N·m (1.4 - 2.0 kgf·m, 10.1 - 14.5 lb·ft)

Note
•
Following order : RR → RL → FL → FR
•
If the brake fluid level falls below the 'MIN' line during air bleed, remove the pressurizing equipment and refill with brake fluid. Then reinstall the pressurizing equipment and continue air bleeding.
•
Bleed the air until there is no air in the brake fluid.
•
Be careful not to open the bleed screw too much. air backflow may occur.
[Front]

Maintenance — Chassis / Brake Fluid / Repair procedures / Inspection illustration

[Rear]

Maintenance — Chassis / Brake Fluid / Repair procedures / Inspection illustration

11.
Close the air shut-off valve (A), remove the air hose (B), and open the valve slowly to drain the air.

Maintenance — Chassis / Brake Fluid / Repair procedures / Inspection illustration

12.
Remove the air hose (A) from the SST (09580 - 3D100).

Maintenance — Chassis / Brake Fluid / Repair procedures / Inspection illustration

13.
Remove the SST (09580 - 3D100).

Maintenance — Chassis / Brake Fluid / Repair procedures / Inspection illustration

14.
Remove the SST (0K585 - E8100).

Maintenance — Chassis / Brake Fluid / Repair procedures / Inspection illustration

15.
Fill the brake fluid to the 'MAX' line.

Specification : DOT 4
Capacity : As required [About (339 - 379 cc)]

16.
Connect the battery negative ( - ) terminal and connect the service interlock connector.
(Refer to Battery Control System - "Auxiliary 12 V Battery - 2WD")
(Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
17.
Enter the IEB air bleeding mode.
(1)
Turn on the vehicle, align the steering wheel, then set the gear knob to "P".
Note
Press the brake pedal as little as possible for turning on the vehicle.
(2)
Press and release the brake pedal 10 times while pushing ESC OFF switch (A).
Note
•
Make sure to press the brake pdal more than 40 mm (1.57 in.) and release it fully to be pressed less than 10 mm (0.39 in.).
•
IEB may make an operation sounds while entering IEB air bleeding mode.
(3)
Turn off and on the vehicle, then press the ESC OFF switch (A) once.

Maintenance — Chassis / Brake Fluid / Repair procedures / Inspection illustration

Note
Press the brake pedal as little as possible for turning on the vehicle.
(4)
If the entry into the air bleeding mode is successful, the 3 lights below are turned on.

Illuminated :
ABS warning light (A), Parking brake/brake warning light (B), ESC OFF warning light (C)

Maintenance — Chassis / Brake Fluid / Repair procedures / Inspection illustration

Note
•
If the warning light do not turn on, go back to the step (1) and retry again.
•
Entering air bleed mode must be done whithin 30 seconds.
•
If warning light turns off during air bleeding, stop the air bleeding immediately. and enter the air bleeding mode again.
•
The air bleeding mode is deceased in each following condition.
1. IG OFF or shift lever knob in D/R/N
2. Detecting DTC
3. Turn off the ESC OFF mode
18.
Fill the brake fluid to the 'MAX' line.

Specification : DOT 4
Capacity : As required [About (339 - 379 cc)]

19.
Open each brake bleed screw (A), drain the brake fluid for about 15 seconds, then press the brake pedal 10 - 20 times and then close the bleed screw.

Tightening torque :
Front : 6.9 - 12.7 N·m (0.7 - 1.3 kgf·m, 5.1 - 9.4 lb·ft, 60.8 - 112.8 lb·in)
Rear : 13.7 - 19.6 N·m (1.4 - 2.0 kgf·m, 10.1 - 14.5 lb·ft)

Note
•
Following order : RR → RL → FL → FR
•
If the brake fluid level falls below the 'MIN' line during air bleed, remove the pressurizing equipment and refill with brake fluid. Then reinstall the pressurizing equipment and continue air bleeding.
•
Bleed the air until there is no air in the brake fluid.
•
Be careful not to open the bleed screw too much. air backflow may occur.
[Front]

Maintenance — Chassis / Brake Fluid / Repair procedures / Inspection illustration

[Rear]

Maintenance — Chassis / Brake Fluid / Repair procedures / Inspection illustration

20.
Fill the brake fluid to the 'MAX' line.

Specification : DOT 4
Capacity : As required [About (339 - 379 cc)]

21.
Install the brake reservoir cap (A).

Maintenance — Chassis / Brake Fluid / Repair procedures / Inspection illustration

22.
If the air is still in the brake fluid, re-try the above procedures.
Note
A minimum interval of 5 minutes is required to prevent damage caused by overheating IEB.

Other information:

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: If the Vehicle Will Not Start

The Kia EV6 may fail to start if the 12-volt battery charge is insufficient or if a related electrical issue is present. Check the battery condition by performing the following steps: Verify that the shifter dial is positioned in P (Park). The Kia EV6 can only be started when the transmission selector is in the Park position.

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: V2L has ended. Battery level has reached the set value

V2L has ended. Battery level has reached the set value When the Kia EV6 high-voltage battery charge reaches the configured discharge limit, the V2L function automatically stops operating and a warning message appears on the instrument cluster. To continue using V2L, set the discharge limit lower than the current battery charge level.

Categories

 
Copyright © 2026 Kia EV6 Manuals � 0.0123