Kia EV6: Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly Removal

Special Service Tool
Tool Name / Number
Illustration
Description
Engine fixture (adapter)
09200 - 4X000

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal / Special Service Tool illustration

Used for anchoring the motor and reducer gear when removing and installing the motor and reducer gear

Removal
Warning
•
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. It is because that lack of knowledge of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
•
When working a high voltage system, the technician must recognize and observe "General Safety Information and Caution". If not, serious accidents like electric shocks and short circuits may be caused.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
Note
•
Use a fender cover to protect the painted surface.
•
Be careful not to damage the connector when disconnecting.
•
When disconnecting a quick connector, refer to the following according to the type of quick connector.
[Type A]
- Remove while pressing the quick connector clamp (A) in the direction of the arrow.
- Do not touch the rubber seal (B) inside the hose.

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

[Type B]
- Pull the quick connector clamp (A) in the direction of the arrow to separate the clamp and remove the hose.
- Do not touch the rubber seal (B) inside the hose.

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

Information
Mark all wiring and hoses to prevent incorrect connections.
1.
Shut off the high voltage circuit.
(Refer to Motor and Reduction Gear System - "High Voltage Shut-off Procedures")
2.
Remove the auxiliary 12 V battery and tray.
(Refer to Battery Control System - "Auxiliary 12V Battery")
3.
Remove the front trunk.
(Refer to Body - "Front Trunk")
4.
Remove the front under cover and the front rear under cover.
(Refer to Front Motor and Reduction Gear System - "Front Under Cover")
5.
Drain the coolant.
(Refer to Electric Vehicle Cooling System - "Coolant")
6.
Drain the front motor and reduction gear oil.
(Refer to Front Motor and Reduction Gear System - "Front Motor and Reduction Gear Oil")
7.
Recover refrigerant by using the refrigerant recovery/recycling/charging machine.
(Refer to Heating,Ventilation And Air Conditioning - "Refrigerant Recovery/Recycling/Charging/Evacuation")
8.
Disconnect the high voltage cable (A) and the wiring fixing clip (B).

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

9.
Disconnect the front wiring connector.
(1)
Remove the junction block cover (A).

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

(2)
Disconnect the front wiring connector (A) and the wiring fixing clip (B).

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

(3)
Remove the front wiring protector (A) from the junction block.

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

10.
Remove the motor ground bolt (A).

Tightening torque :
6.9 - 9.8 N·m (0.7 - 1.0 kgf·m, 5.1 - 7.2 lb·ft)

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

11.
Disconnect the 3-way valve coolant hose (A) after releasing the quick connector.

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

12.
Disconnect the motor & reduction oil cooler coolant hose (A) after releasing the quick connector.

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

13.
Disconnect the inverter coolant hose (A) after releasing the quick connector.

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

14.
Disconnect the battery heater hose (A) after releasing the quick connector.

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

15.
Disconnect the coolant temperature sensor connector (A).

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

16.
Disconnect the coolant hose (A) after releasing the quick connector.

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

17.
Remove the A/C pipe.
(1)
Disconnect the A/C pressure transducer connector (A).
(2)
Remove the A/C pipe (B) after removing the mounting nut.

Tightening torque :
8.8 - 13.7 N·m (0.9 - 1.4 kgf·m, 6.5 - 10.1 lb·ft)

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

(3)
Remove the A/C pipe (A) after removing the mounting nut.

Tightening torque :
8.8 - 13.7 N·m (0.9 - 1.4 kgf·m, 6.5 - 10.1 lb·ft)

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

(4)
Disconnect the A/C pipe (A) from the fixing bracket.

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

18.
Separate the steering universal joint from the steering gear box.
(1)
Remove the steering universal joint bolt (A).

Tightening torque :
49.0 - 58.8 N·m (5.0 - 6.0 kgf·m, 36.2 - 43.4 lb·ft)

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

Note
Do not reuse steering universal joint bolt.
(2)
Separate the steering universal joint (A) in the direction of the arrow.

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

19.
Disconnect the water condenser hose (A) after releasing the quick connector.

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

20.
Disconnect the high voltage battery coolant temperature sensor connector (A).

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

21.
Disconnect the high voltage battery cooling hose (A) after releasing the quick connector.

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

22.
Remove the high voltage battery cover (A) after removing the mounting bolts.

Tightening torque :
7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

23.
Disconnect the front high voltage junction box power cable (A).

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

Note
How to disconnect the connector
1)
Release the locking clip (A) by pulling it.
2)
Disconnect the connector by pushing the lever (A) in the direction of the arrow while pressing the locking clip (B).

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

24.
Disconnect the R-MDPS connector (A) and wiring fixing clip (B).

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

25.
Remove the electric water pump (EWP).
(Refer to Cooling System - "Electric Water Pump (EWP)")
26.
Remove the front driveshaft.
(Refer to Driveshaft Assembly - "Front Driveshaft")
27.
Remove the stabilizer bar link (A) from the front strut assembly after removing the mounting nut.

Tightening torque :
98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

Note
•
Hold the outer hex (A) when removing or installing the nut (B).

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

•
Be careful not to damage the boot of the link.
•
Always use hand tools when removing and installing the stabilizer bar link nut.
28.
Support the front subframe using a table lift.

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

29.
Remove the front subframe bolts and nut (A).

Tightening torque :
107.9 - 127.5 N·m (11.0 - 13.0 kgf·m, 79.6 - 94.0 lb·ft)

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

30.
Lift up the vehicle slowly to remove the front motor and reduction gear assembly and front subframe.
Note
•
Before removing the motor and reducer assembly, make sure hoses and wire connectors are disconnected.
•
When removing the motor and reducer assembly, be careful not to damage any surrounding parts or body components.
31.
Remove the protectors and wiring cables around the motor and reduction gear assembly.

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

32.
Remove the motor & reduction gear oil cooler.
(Refer to Cooling System - "Motor & Reduction Gear Oil Cooler")
33.
Remove the 3 way valve.
(Refer to Cooling System - "3Way Valve")
34.
Remove the coolant distribution pipe.
(Refer to Cooling System - "Coolant Distribution Pipe")
35.
Remove the electric oil pump.
(Refer to Motor and Reduction Gear System - "Electronic Oil Pump (EOP)")
36.
Remove the battery heater.
(Refer to Cooling System - "Battery Heater")
37.
Remove the front high voltage junction box.
(Refer to Battery Control System - "Front High Voltage Junction Box")
38.
Remove the inverter assembly.
(Refer to Battery Control System - "Inverter Assembly - 4WD")
39.
Remove the electric A/C compressor.
(Refer to Heating,Ventilation And Air Conditioning - "Electric A/C Compressor")
40.
Support the motor and reduction gear assembly using engine cranes and SST (09200 - 4X000).

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

Note
Install the SST (09200 - 4X000) to the front motor and reduction gear assembly hangers.

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

41.
Remove the motor mounting bracket bolts and nuts (A).

Tightening torque :
107.9 - 127.5 N·m (11.0 - 13.0 kgf·m, 79.6 - 94.0 lb·ft)

[LH Motor Mounting Bracket]

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

[RH Motor Mounting Bracket]

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

[RR Motor Mounting Bracket]

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

42.
Remove the front motor and reduction gear assembly from the front subframe by lifting the engine crane upwards.
43.
Remove the motor and reduction gear mounting bracket (A) after removing the mounting bolts.

Tightening torque :
63.7 - 83.4 N·m (6.5 - 8.5 kgf·m, 47.0 - 61.5 lb·ft)

[LH Motor Mounting Bracket]

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

[RR Motor Mounting Bracket]

Motor and Reduction Gear System — Front Motor and Reduction Gear System / Front Motor and Reduction Gear Assembly / Removal illustration

Other information:

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: ECO mode

ECO mode in the Kia EV6 is designed to maximize electric driving efficiency by reducing energy consumption and minimizing driving behaviors that may negatively affect battery range. The overall electric energy efficiency of the Kia EV6 can vary depending on driving habits, traffic conditions, terrain, climate settings, and road surfaces.

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Charging wireless smart phone

Remove all objects from the Kia EV6 wireless charging pad, including the smart key and metallic accessories. Foreign objects may interfere with charging operation or cause overheating. Position the smartphone in the center of the Kia EV6 charging pad. When charging begins, the Kia EV6 charging indicator changes to orange.

Categories

 
Copyright © 2026 Kia EV6 Manuals ⏱ 0.014