Kia EV6: Front Suspension System / Front Subframe Removal and Installation - 2WD

Special Service Tool
Tool Name / Number
Illustration
Description
Ball joint puller
09568 - 2J100

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Special Service Tool illustration

Used for removal of tie rod end
Lower arm ball joint remover
0K545 - A9100

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Special Service Tool illustration

Used for removal of front lower arm ball joint

Removal
Warning
•
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
•
When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
1.
Align the steering wheel straight.
2.
Turn the IG to 'OFF'.
3.
Disconnect the battery negative ( - ) terminal and the service interlock connector.
(Refer to Battery Control System - "Auxiliary 12 V Battery - 2WD")
4.
Secure the steering wheel to prevent movement.
Note
Changing the clockspring neutral position by rotating the steering wheel with the steering column universal joint removed may result in open circuit and faulty folding of the cable inside the clockspring after installation.
5.
Remove the front trunk.
(Refer to Body - "Front Trunk")
6.
Separate the steering universal joint from the steering gear box.
(1)
Remove the steering universal joint bolt (A).

Tightening torque :
49 - 58.8 N·m (5.0 - 6.0 kgf·m, 36.2 - 43.4 lb·ft)

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

Note
Do not reuse the steering universal joint bolt.
(2)
Separate the steering universal joint (A) in the direction of the arrow.

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

7.
Separate the air conditioning compressor.
(1)
Remove the air conditioning compressor bolts (A).

Tightening torque :
21.6 - 29.4 N·m (2.2 - 3.0 kgf·m, 15.9 - 21.7 lb·ft)

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

(2)
Hold the air conditioning compressor (A) on the body using a cable tie.

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

8.
Remove the front under cover.
(Refer to Motor and Reduction Gear System - "Front Under Cover")
9.
Remove the front wheel and tires.
(Refer to Wheel and Tire - "Wheel")
10.
Remove the stabilizer bar link (A) from the front strut assembly after removing the nut.

Tightening torque :
98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

Note
•
Hold the outer hex (A) when removing or installing the nut (B).

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

•
Be careful not to damage the boot of the link.
•
Use a hand tool when removing or installing the stabilizer bar link nut.
11.
Separate the lower arm ball joint from the front axle using SST (0K545 - A9100).
(1)
Remove the split pin (D).
(2)
Remove the lower arm bolt (A), washer (B), and nut (C).

Tightening torque :
98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

Information
Hold the lower arm ball joint bolt and remove or install the nut.
Note
•
Do not reuse the split pin.
•
Be careful not to change the position of the bolt, nut, and washer when installing.
(3)
Place the support bolts (A) to the lower arm ball joint mounting hole, and then rotate them to install the SST.

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

Information
Use the support body (A) of the SST (0K545 - A9100).

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

(4)
Install the support body (B) in the front axle groove (A).

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

(5)
Rotate the bolt (A) to insert the support body (B) to release the front knuckle.

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

(6)
Install the main body (A) between the front strut assembly and front lower arm.

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

Information
Use the main body (A) of the SST (0K545 - A9100).

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

(7)
Secure the main body with the wire (A) to prevent it from falling.

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

(8)
Install the c-clamp (A) by rotating the handle (B) to prevent the main body from slipping.

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

Information
Use the C-clamp (A) of the SST (0K545 - A9100).

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

(9)
Tighten the bolt (A) to widen the gap of the main body so that the front lower arm can be removed from the front knuckle.

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

12.
Separate the tie rod end ball joint from the front axle.
(1)
Remove the split pin (A).
(2)
Remove the lock nut (B), and washer (C).

Tightening torque :
98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

Note
•
Do not reuse the split pin.
•
Do not reuse the lock nut.
•
Be careful not to damage the boot of the link.
•
Use a hand tool when removing or installing the lock nut.
(3)
Separate the tie rod end ball joint (A) using SST (09568 - 2J100).

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

13.
Remove the PTC heater bolts (A).

Tightening torque :
8.8 - 11.8 N·m (0.9 - 1.2 kgf·m, 6.5 - 8.7 lb·ft)

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

14.
Remove the 3-way valve bolts (A).

Tightening torque :
8.8 - 11.8 N·m (0.9 - 1.2 kgf·m, 6.5 - 8.7 lb·ft)

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

15.
Remove the distribution pipe bracket bolts (A).

Tightening torque :
8.8 - 11.8 N·m (0.9 - 1.2 kgf·m, 6.5 - 8.7 lb·ft)

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

16.
Remove the battery EWP bolts (A) and nut (B).

Tightening torque :
8.8 - 11.8 N·m (0.9 - 1.2 kgf·m, 6.5 - 8.7 lb·ft)

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

17.
Disconnect the MDPS power pack connectors.
(1)
Pull the connector keys (A) in the direction of the arrow.

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

(2)
Disconnect the connectors (A).

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

18.
Remove the ground cables (A) after removing the bolts.

Tightening torque :
8.8 - 11.8 N·m (0.9 - 1.2 kgf·m, 6.5 - 8.7 lb·ft)

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

19.
Remove the wiring clips (A) on the front subframe.

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

20.
Remove the front subframe bar (A) after removing the bolts.

Tightening torque :
166.7 - 186.3 N·m (17.0 - 19.0 kgf·m, 123 - 137.4 lb·ft)

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

21.
Support the front subframe with the table lift (A) securely.

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

Warning
Be careful not to lift the table lift too much. The vehicle may fall due to a change of center of gravity.
Caution
Do not use small jacks such as transaxle jacks. The front subframe may tilt and cause injury.
Information
•
When installing or removing the front subframe stay bolts and nuts, adjust the table lift position to make a workspace.
•
Place the rubber block (A) between the front subframe and table lift to maintain level.

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

22.
Remove the bolts and nuts, and then lower the table lift slowly to remove the front subframe (A).

Tightening torque :
112.8 - 122.6 N·m (11.5 - 12.5 kgf·m, 83.2 - 90.4 lb·ft) + 85 - 95°

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

23.
Remove the steering gear box (A) after removing the bolts.

Tightening torque :
107.9 - 127.5 N·m (11.0 - 13.0 kgf·m, 79.6 - 94.0 lb·ft)

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

Note
When installing the steering gear box, pre-tighten all bolts and tighten to the specified torque.
24.
Remove the front lower arm (A) after removing the bolts (B, C), nuts, and washers.

Tightening torque :
B : 117.7 - 137.3 N·m (12.0 - 14.0 kgf·m, 86.8 - 101.3 lb·ft)
C : 156.9 - 176.5 N·m (16.0 - 18.0 kgf·m, 115.7 - 130.2 lb·ft)

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

25.
Remove the front stabilizer bar (A) after removing the bolts.

Tightening torque :
53.9 - 63.7 N·m (5.5 - 6.5 kgf·m, 39.8 - 47.0 lb·ft)

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 2WD / Removal illustration

Installation
Warning
•
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
•
When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
1.
Install in the reverse order of removal.
2.
Check the alignment.
(Refer to Alignment - "Repair Procedures")

Other information:

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: General Safety Information and Caution

Precaution (R-134a) When Handling Refrigerant 1. R-134a liquid refrigerant is highly volatile. A drop on the skin of your hand could result in localized frostbite. When handling the refrigerant, be sure to wear gloves. 2. It is standard practice to wear goggles or glasses to protect your eyes, and gloves to protect your hands.

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: 1. Manufacturer or Brand Identification

The tire sidewall of your Kia EV6 displays the name of the manufacturer or the tire brand. This information helps identify the tire model and ensures that replacement tires meet the original equipment specifications recommended for the Kia EV6. 2. Maximum Permissible Inflation Pressure This value indicates the highest air pressure that may safely be placed inside the tire.

Categories

 
Copyright © 2026 Kia EV6 Manuals ⏱ 0.0201