Kia EV6: Suspension System / Front Suspension System

Contents:

Components and Components Location. Front Strut Assembly Components and Components Location

Components and Components Location

Components and Components Location

Suspension System — Front Suspension System / Components and Components Location illustration

1. Front Strut Assembly
1-a. 53.9 - 73.5 N·m (5.5 - 7.5 kgf·m, 39.8 - 54.2 lb·ft)
1-b. 156.9 - 176.5 N·m (16.0 - 18.0 kgf·m, 115.7 - 130.2 lb·ft)
2. Front Sub Frame
2-a. 112.8 - 122.6 N·m (11.5 - 12.5 kgf·m, 83.2 - 90.4 lb·ft) + 85 - 95°
3. Front Sub Frame Bar
3-a. 166.7 - 186.3 N·m (17.0 - 19.0 kgf·m, 123.0 - 137.4 lb·ft)
4. Front Lower Arm
4-a. 117.7 - 137.3 N·m (12.0 - 14.0 kgf·m, 86.8 - 101.3 lb·ft)
4-b. 156.9 - 176.5 N·m (16.0 - 18.0 kgf·m, 115.7 - 130.2 lb·ft)
5. Front Stabilizer Bar Link
5-a. 98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)
6. Front Stabilizer Bar
6-a. 53.9 - 63.7 N·m (5.5 - 6.5 kgf·m, 39.8 - 47.0 lb·ft)
7. Front Lower Arm Ball Joint
7-a. 98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)


Front Strut Assembly Components and Components Location

Components and Components Location

Suspension System — Front Suspension System / Front Strut Assembly / Components and Components Location illustration

1. Insulator Cap
2. Insulator Assembly
2-a. 53.9 - 73.5 N·m (5.5 - 7.5 kgf·m, 39.8 - 54.2 lb·ft)
3. Strut Bearing
4. Bumper Stopper
5. Dust Cover
6. Coil Spring
7. Spring Lower Pad
8. Strut Assembly
8-a. 117.7 - 127.5 N·m (12.0 - 13.0 kgf·m, 86.8 - 94.0 lb·ft)

Front Strut Assembly Removal and Installation

Removal
1.
Remove the front strut upper mounting nuts (A).

Tightening torque :
53.9 - 73.5 N·m (5.5 - 7.5 kgf·m, 39.8 - 54.2 lb·ft)

Suspension System — Front Suspension System / Front Strut Assembly / Removal and Installation / Removal illustration

2.
Remove the front wheel and tires.
(Refer to Wheel and Tire - "Wheel")
3.
Remove the brake hose bracket (A) after removing the bolt.

Tightening torque :
19.6 - 29.4 N·m (2.0 - 3.0 kgf·m, 14.5 - 21.7 lb·ft)

Suspension System — Front Suspension System / Front Strut Assembly / Removal and Installation / Removal illustration

4.
Remove the stabilizer bar link (A) from the front strut assembly after removing the nut.

Tightening torque :
98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)

Suspension System — Front Suspension System / Front Strut Assembly / Removal and Installation / Removal illustration

Note
•
Hold the outer hex (A) when removing or installing the nut (B).

Suspension System — Front Suspension System / Front Strut Assembly / Removal and Installation / Removal illustration

•
Be careful not to damage the boot of the link.
•
Use a hand tool when removing or installing the stabilizer bar link nut.
5.
Remove the front strut assembly (A) from the front axle after removing the bolts and nuts.

Tightening torque :
156.9 - 176.5 N·m (16.0 - 18.0 kgf·m, 115.7 - 130.2 lb·ft)

Suspension System — Front Suspension System / Front Strut Assembly / Removal and Installation / Removal illustration

Installation
1.
Install in the reverse order of removal.
Note
Pre-tighten the front strut upper nuts and put the vehicle down on the ground and tighten the front strut upper nuts to tightening torque value.

Front Strut Assembly Disassembly

Special Service Tool
Tool Name / Number
Illustration
Description
Shock absorber lock nut remover.
0K546 - F6100

Suspension System — Front Suspension System / Front Strut Assembly / Disassembly / Special Service Tool illustration

Used for removal or installing of front strut lock nut.

Disassembly
1.
Remove the front strut assembly.
(Refer to Front Suspension System - "Front Strut Assembly")
2.
Install the front strut assembly (A) to the spring compressor.

Suspension System — Front Suspension System / Front Strut Assembly / Disassembly illustration

3.
Remove the insulator cap (A).

Suspension System — Front Suspension System / Front Strut Assembly / Disassembly illustration

4.
Compress the coil spring (A) slightly until it is tensioned using the spring compressor.

Suspension System — Front Suspension System / Front Strut Assembly / Disassembly illustration

Information
Protect the coil spring when compressing using rubber such as plastic hose, etc to prevent the damage.

Suspension System — Front Suspension System / Front Strut Assembly / Disassembly illustration

5.
Remove the nut using the SST (0K546 - F6100).

Tightening torque :
117.7 - 127.5 N·m (12.0 - 13.0 kgf·m, 86.8 - 94.0 lb·ft)

Suspension System — Front Suspension System / Front Strut Assembly / Disassembly illustration

6.
Disassemble insulator (A), strut bearing (B), bumper stopper (C), dust cover (D), coil spring (E), spring lower pad (F) from the strut (G).

Suspension System — Front Suspension System / Front Strut Assembly / Disassembly illustration

Front Strut Assembly Inspection

Inspection
1.
Check the strut insulator bearing for wear and damage.
2.
Check the rubber parts for damage and deterioration.
3.
Compress and extend the piston rod (A) and check that there is no abnormal resistance or unusual sound during operation.

Suspension System — Front Suspension System / Front Strut Assembly / Inspection illustration

Disposal
1.
Fully extend the strut rod.
2.
Drill a hole in the (A) area of the cylinder to deflate gas.

Suspension System — Front Suspension System / Front Strut Assembly / Inspection / Disposal illustration

Information
The gas coming out is harmless, but be careful of debris that may fly when drilling.

Front Strut Assembly Reassembly

Special Service Tool
Tool Name / Number
Illustration
Description
Shock absorber lock nut remover.
0K546 - F6100

Suspension System — Front Suspension System / Front Strut Assembly / Reassembly / Special Service Tool illustration

Used for removal or installing of front strut lock nut

Reassembly
1.
Assemble the insulator (A), strut bearing (B), bumper stopper (C), dust cover (D), coil spring (E), and spring lower pad (F) on the strut (G).

Suspension System — Front Suspension System / Front Strut Assembly / Reassembly illustration

Note
•
Align the protrusions of the strut bearing upper housing and the lower housing when reassembling.

Suspension System — Front Suspension System / Front Strut Assembly / Reassembly illustration

•
Align the protrusion of the insulator (A) and groove of the bearing (B) when assembling.

Suspension System — Front Suspension System / Front Strut Assembly / Reassembly illustration

•
When installing insulator assembly to the front strut assembly, align the protrusion (A) of the strut bearing and knuckle mounting parts (B).

Suspension System — Front Suspension System / Front Strut Assembly / Reassembly illustration

•
When installing the coil spring, make sure that the gap (A) between the spring top start and 180° past point (B) and the spring upper pad is within the allowable value.

Allowable clearance (A) :
3 mm (0.1181 in.)

Suspension System — Front Suspension System / Front Strut Assembly / Reassembly illustration

2.
Install the front strut assembly (A) to the spring compressor.

Suspension System — Front Suspension System / Front Strut Assembly / Reassembly illustration

3.
Compress the coil spring (A) slightly until it is tensioned using the spring compressor.

Suspension System — Front Suspension System / Front Strut Assembly / Reassembly illustration

Information
Protect the coil spring when compressing using rubber such as plastic hose, etc to prevent the damage.

Suspension System — Front Suspension System / Front Strut Assembly / Reassembly illustration

4.
Install the self locking nut using SST (0K546 - F6100).

Tightening torque :
117.7 - 127.5 N·m (12.0 - 13.0 kgf·m, 86.8 - 94.0 lb·ft)

Suspension System — Front Suspension System / Front Strut Assembly / Reassembly illustration

Note
Do not reuse the self locking nut.
5.
Install the insulator cap (A).

Suspension System — Front Suspension System / Front Strut Assembly / Reassembly illustration

6.
Install the front strut assembly.
(Refer to Front Suspension System - "Front Strut Assembly")

Front Lower Arm Removal and Installation

Special Service Tool
Tool Name / Number
Illustration
Description
Lower arm ball joint remover
0K545 - A9100

Suspension System — Front Suspension System / Front Lower Arm / Removal and Installation / Special Service Tool illustration

Used for removal of front lower arm ball joint

Removal
[Front Lower Arm Ball Joint]
1.
Remove the front wheel and tires.
(Refer to Wheel and Tire - "Wheel")
2.
Remove the front under cover.
(Refer to Motor and Reduction Gear System - "Front Under Cover")
3.
Separate the lower arm ball joint from the front axle using SST (0K545 - A9100).
(1)
Remove the split pin (D).
(2)
Remove the lower arm bolt (A), washer (B), and nut (C).

Tightening torque :
98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)

Suspension System — Front Suspension System / Front Lower Arm / Removal and Installation / Removal illustration

Information
Hold the lower arm ball joint bolt and remove or install the nut.
Note
•
Do not reuse the split pin.
•
Be careful not to change the position of the bolt, nut, and washer when installing.
(3)
Place the support bolts (A) to the lower arm ball joint mounting hole, and then rotate them to install the SST.

Suspension System — Front Suspension System / Front Lower Arm / Removal and Installation / Removal illustration

Information
Use the support body (A) of the SST (0K545 - A9100).

Suspension System — Front Suspension System / Front Lower Arm / Removal and Installation / Removal illustration

(4)
Install the support body (B) in the front axle groove (A).

Suspension System — Front Suspension System / Front Lower Arm / Removal and Installation / Removal illustration

(5)
Rotate the bolt (A) to insert the support body (B) to release the front knuckle.

Suspension System — Front Suspension System / Front Lower Arm / Removal and Installation / Removal illustration

(6)
Install the main body (A) between the front strut assembly and front lower arm.

Suspension System — Front Suspension System / Front Lower Arm / Removal and Installation / Removal illustration

Information
Use the main body (A) of the SST (0K545 - A9100).

Suspension System — Front Suspension System / Front Lower Arm / Removal and Installation / Removal illustration

(7)
Secure the main body with the wire (A) to prevent it from falling.

Suspension System — Front Suspension System / Front Lower Arm / Removal and Installation / Removal illustration

(8)
Install the c-clamp (A) by rotating the handle (B) to prevent the main body from slipping.

Suspension System — Front Suspension System / Front Lower Arm / Removal and Installation / Removal illustration

Information
Use the C-clamp (A) of the SST (0K545 - A9100).

Suspension System — Front Suspension System / Front Lower Arm / Removal and Installation / Removal illustration

(9)
Tighten the bolt (A) to widen the gap of the main body so that the front lower arm can be removed from the front knuckle.

Suspension System — Front Suspension System / Front Lower Arm / Removal and Installation / Removal illustration

4.
Remove the lower arm ball joint (A) after removing the nuts.

Tightening torque :
98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)

Suspension System — Front Suspension System / Front Lower Arm / Removal and Installation / Removal illustration

[Front Lower Arm Assembly]
1.
Remove the front wheel and tires.
(Refer to Wheel and Tire - "Wheel")
2.
Separate the lower arm ball joint from the front axle using SST (0K545 - A9100).
(1)
Remove the split pin (D).
(2)
Remove the lower arm bolt (A), washer (B), and nut (C).

Tightening torque :
98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)

Suspension System — Front Suspension System / Front Lower Arm / Removal and Installation / Removal illustration

Information
Hold the lower arm ball joint bolt and remove or install the nut.
Note
•
Do not reuse the split pin.
•
Be careful not to change the position of the bolt, nut, and washer when installing.
(3)
Place the support bolts (A) to the lower arm ball joint mounting hole, and then rotate them to install the SST.

Suspension System — Front Suspension System / Front Lower Arm / Removal and Installation / Removal illustration

Information
Use the support body (A) of the SST (0K545 - A9100).

Suspension System — Front Suspension System / Front Lower Arm / Removal and Installation / Removal illustration

(4)
Install the support body (B) in the front axle groove (A).

Suspension System — Front Suspension System / Front Lower Arm / Removal and Installation / Removal illustration

(5)
Rotate the bolt (A) to insert the support body (B) to release the front knuckle.

Suspension System — Front Suspension System / Front Lower Arm / Removal and Installation / Removal illustration

(6)
Install the main body (A) between the front strut assembly and front lower arm.

Suspension System — Front Suspension System / Front Lower Arm / Removal and Installation / Removal illustration

Information
Use the main body (A) of the SST (0K545 - A9100).

Suspension System — Front Suspension System / Front Lower Arm / Removal and Installation / Removal illustration

(7)
Secure the main body with the wire (A) to prevent it from falling.

Suspension System — Front Suspension System / Front Lower Arm / Removal and Installation / Removal illustration

(8)
Install the c-clamp (A) by rotating the handle (B) to prevent the main body from slipping.

Suspension System — Front Suspension System / Front Lower Arm / Removal and Installation / Removal illustration

Information
Use the C-clamp (A) of the SST (0K545 - A9100).

Suspension System — Front Suspension System / Front Lower Arm / Removal and Installation / Removal illustration

(9)
Tighten the bolt (A) to widen the gap of the main body so that the front lower arm can be removed from the front knuckle.

Suspension System — Front Suspension System / Front Lower Arm / Removal and Installation / Removal illustration

3.
Remove the front lower arm (C) after removing the bolts, nut, and washer.

Tightening torque :
(A) :117.7 - 137.3 N·m (12.0 - 14.0 kgf·m, 86.8 - 101.3 lb·ft)
(B) :156.9 - 176.5 N·m (16.0 - 18.0 kgf·m, 115.7 - 130.2 lb·ft)

Suspension System — Front Suspension System / Front Lower Arm / Removal and Installation / Removal illustration

Installation
1.
Install in the reverse order of removal.
2.
Check the alignment.
(Refer to Alignment - "Repair Procedures")

Front Lower Arm Inspection

Inspection
1.
Check the bushing for wear or aging.
2.
Check the lower arm for bent or damaged.
3.
Check all bolts.

Front Lower Arm Replacement - Lower Arm 'G' Bushing

Special Service Tool
Tool Name / Number
Illustration
Description
Lower arm 'G' bushing replacement tool
09545 - AL100

Suspension System — Front Suspension System / Front Lower Arm / Replacement - Lower Arm 'G' Bushing / Special Service Tool illustration

Used for replacement of the lower arm 'G' bushing

Replacement - Lower Arm 'G' Bushing
Information
Replace the lower arm 'G' bushing if it only has a crack, noise from bushing without cracks can be improved by applying silicone oil.
1.
Replace the lower arm 'G' bushing by using the SST (09545 - AL100).

Suspension System — Front Suspension System / Front Lower Arm / Replacement - Lower Arm 'G' Bushing illustration

Suspension System — Front Suspension System / Front Lower Arm / Replacement - Lower Arm 'G' Bushing illustration

Information
Refer to the enclosed manual for detailed usage instructions.
Caution
•
Wear personal protective equipment during press operation.
•
When the press is in operation, ensure that no part of the body comes into contact within the operating range.
•
Due to the risk of injury from falling tools and parts, before operating the press, ensure that all tools and components are securely positioned in their proper places.
Note
•
Lubricate the bushings and mounting surface with grease during the operation.
•
Measure the void spacing (A), (B) to ensure that the bushing can be properly installed in the correct direction.

(A) : Ball joint side
(B) : Opposite side

Suspension System — Front Suspension System / Front Lower Arm / Replacement - Lower Arm 'G' Bushing illustration

Information
•
Refer to the enclosed manual for void spacing specifications for each vehicle model.
•
There may be no difference in void spacing for used bushing due to wear.
•
Be careful not to install the bushing at the incorrect angle.

Installaion angle (A) : Angle formed counterclockwise from 'A' bushing (B) and 'G' bushing (C) reference

Suspension System — Front Suspension System / Front Lower Arm / Replacement - Lower Arm 'G' Bushing illustration

Information
Refer to the enclosed manual for installation angle specifications for each vehicle model.
•
Clean the bushing mounting surface (A) from any foreign substances using a clean cloth or similar material when installing.

Suspension System — Front Suspension System / Front Lower Arm / Replacement - Lower Arm 'G' Bushing illustration

•
Ensure that the marking angle (A) of the bushing and the lower arm does not deviate from the reference value.

Reference Value : ± 3°

Suspension System — Front Suspension System / Front Lower Arm / Replacement - Lower Arm 'G' Bushing illustration

•
If excessive pressure is applied after installation is complete, it may result in damage to the components and tools.

Front Stabilizer Bar Removal and Installation

Removal
[Front Stabilizer Bar Link]
1.
Remove the front wheel and tires.
(Refer to Wheel and Tire - "Wheel")
2.
Remove the stabilizer bar link (A) from the front strut assembly after removing the nut.

Tightening torque :
98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)

Suspension System — Front Suspension System / Front Stabilizer Bar / Removal and Installation / Removal illustration

Note
•
Hold the outer hex (A) when removing or installing the nut (B).

Suspension System — Front Suspension System / Front Stabilizer Bar / Removal and Installation / Removal illustration

•
Be careful not to damage the boot of the link.
•
Use a hand tool when removing or installing the stabilizer bar link nut.
3.
Remove the stabilizer bar link (A) from the stabilizer bar after removing the nut.

Tightening torque :
98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)

Suspension System — Front Suspension System / Front Stabilizer Bar / Removal and Installation / Removal illustration

Note
•
Hold the outer hex (A) when removing or installing the nut (B).

Suspension System — Front Suspension System / Front Stabilizer Bar / Removal and Installation / Removal illustration

•
Be careful not to damage the boot of the link.
•
Use a hand tool when removing or installing the stabilizer bar link nut.
[Front Stabilizer Bar]
1.
Remove the front wheel and tires.
(Refer to Wheel and Tire - "Wheel")
2.
Remove the front under cover.
(Refer to Motor and Reduction Gear System - "Front Under Cover")
3.
Remove the stabilizer bar link (A) from the stabilizer bar after removing the nut.

Tightening torque :
98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)

Suspension System — Front Suspension System / Front Stabilizer Bar / Removal and Installation / Removal illustration

Note
•
Hold the outer hex (A) when removing or installing the nut (B).

Suspension System — Front Suspension System / Front Stabilizer Bar / Removal and Installation / Removal illustration

•
Be careful not to damage the boot of the link.
•
Use a hand tool when removing or installing the stabilizer bar link nut.
4.
Remove the front wheel guard.
(Refer to Body - "Wheel Guard")
5.
Remove the front stabilizer bar (A) after removing the bolts.

Tightening torque :
53.9 - 63.7 N·m (5.5 - 6.5 kgf·m, 39.8 - 47.0 lb·ft)

[LH]

Suspension System — Front Suspension System / Front Stabilizer Bar / Removal and Installation / Removal illustration

[RH]

Suspension System — Front Suspension System / Front Stabilizer Bar / Removal and Installation / Removal illustration

Installation
1.
Install in the reverse order of removal.
2.
Check the alignment.
(Refer to Alignment - "Repair Procedures")

Front Stabilizer Bar Inspection. Front Stabilizer Bar Disassembly and Reassembly

Front Stabilizer Bar Inspection

Inspection
1.
Check the stabilizer bar bushing for damage.
2.
Check the stabilizer bar link ball joint for damage.

Front Stabilizer Bar Disassembly and Reassembly

Disassembly
1.
Remove the stabilizer bar bushing bracket (A) using a flat-head screwdriver or suitable tool.

Suspension System — Front Suspension System / Front Stabilizer Bar / Disassembly and Reassembly / Disassembly illustration

Note
Take care not to deform when removing and replace if deformed.
2.
Remove the stabilizer bar bushing (A).

Suspension System — Front Suspension System / Front Stabilizer Bar / Disassembly and Reassembly / Disassembly illustration

Note
Do not reuse the stabilizer bar bushing (A).
Reassembly
1.
Reassemble in the reverse order of disassembly.

Front Subframe Removal and Installation - 2WD ➤

Front Subframe Removal and Installation - 4WD

Removal
Warning
•
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
•
When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
1.
Remove the front motor and reduction gear assembly.
(Refer to Front Motor and Reduction Gear System - "Front Motor and Reduction Gear Assembly")
2.
Remove the mounting bracket (A) after removing the bolts.

Tightening torque :
63.7 - 83.4 N·m (6.5 - 8.5 kgf·m, 47.0 - 61.5 lb·ft)

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 4WD / Removal illustration

3.
Remove the steering gear box (A) after removing the bolts.

Tightening torque :
107.9 - 127.5 N·m (11.0 - 13.0 kgf·m, 79.6 - 94.0 lb·ft)

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 4WD / Removal illustration

Note
When installing the steering gear box, pre-tighten all bolts and tighten to the specified torque.
4.
Remove the front stabilizer bar (A) after removing the bolts.

Tightening torque :
53.9 - 63.7 N·m (5.5 - 6.5 kgf·m, 39.8 - 47.0 lb·ft)

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 4WD / Removal illustration

5.
Remove the front lower arm (A) after removing the bolts, nuts, and washers.

Tightening torque :
(B) : 117.7 - 137.3 N·m (12.0 - 14.0 kgf·m, 86.8 - 101.3 lb·ft)
(C) : 156.9 - 176.5 N·m (16.0 - 18.0 kgf·m, 115.7 - 130.2 lb·ft)

Suspension System — Front Suspension System / Front Subframe / Removal and Installation - 4WD / Removal illustration

Installation
Warning
•
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
•
When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
1.
Install in the reverse order of removal.
2.
Check the alignment.
(Refer to Alignment - "Repair Procedures")

Other information:

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Main components of the occupant detection system

A highly sensitive detection sensor is integrated into the front passenger seat cushion of the Kia EV6. An advanced electronic monitoring system continuously evaluates occupant conditions to determine whether the front passenger airbag should remain activated or be automatically deactivated. The overhead console indicator illuminates the message PASSENGER AIR BAG OFF ( ) whenever the front passenger airbag system has been deactivated by the Occupant Detection System.

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: How to remove ice from door handles

During severe winter weather conditions, ice may accumulate inside or around the retractable exterior door handles of the Kia EV6, preventing normal operation. In many cases, gently tapping around the handle area can help break the ice and restore movement. Remove accumulated ice by gently tapping around the perimeter of the Kia EV6 door handle using the bottom of your fist in a circular motion.

 
Copyright © 2026 Kia EV6 Manuals ⏱ 0.022