Kia EV6: Battery Control System (Long Range) / High Voltage Distributing System

Contents:

Components and Components Location

Component
2WD

Battery Control System (Long Range) — High Voltage Distributing System / Components and Components Location / Component illustration

1. Front High Voltage Junction Box
1-a. 4.9 - 7.8 N·m (0.5 - 0.8 kgf·m, 3.6 - 5.8 lb·ft, 43.4 - 69.4 lb·ft)
2. High Voltage Junction Box Service Cover
2-a. 3.9 - 5.9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)
2-b. 6.9 - 9.8 N·m (0.7 - 1.0 kgf·m, 5.1 - 7.2 lb·ft)
3. Rear High Voltage Junction Box
3-a. 15.7 - 23.5 N·m (1.6 - 2.4 kgf·m, 11.6 - 17.4 lb·ft)
3-b. 17.7 - 26.5 N·m (1.8 - 2.7 kgf·m, 13.0 - 19.5 lb·ft)

4WD

Battery Control System (Long Range) — High Voltage Distributing System / Components and Components Location / Component illustration

1. High Voltage Junction Box Service Cover
1-a. 3.9 - 5.9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)
1-b. 6.9 - 9.8 N·m (0.7 - 1.0 kgf·m, 5.1 - 7.2 lb·ft)
2. Front High Voltage Junction Box
2-a. 6.9 - 9.8 N·m (0.7 - 1.0 kgf·m, 5.1 - 7.2 lb·ft)
3. High Voltage Junction Box Service Cover
3-a. 3.9 - 5.9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)
3-b. 6.9 - 9.8 N·m (0.7 - 1.0 kgf·m, 5.1 - 7.2 lb·ft)
4. Rear High Voltage Junction Box
4-a. 15.7 - 23.5 N·m (1.6 - 2.4 kgf·m, 11.6 - 17.4 lb·ft)
4-b. 17.7 - 26.5 N·m (1.8 - 2.7 kgf·m, 13.0 - 19.5 lb·ft)

Front High Voltage Junction Box Description and Operation

Description
[2WD]
•
It works as the power distributor for connecting the high voltage battery power and high voltage components (A/C compressor, PTC heater, etc.).
•
It is installed in front cross member and includes bus bar, fuse and PTC relay ( + ).

Battery Control System (Long Range) — High Voltage Distributing System / Front High Voltage Junction Box / Description and Operation / Description illustration

NO
System
Possible Cause
1
Battery signal
-
2
Battery PTC relay
Battery Management Unit (BMU) relay control
3
Battery PTC fuse
20 A
4
PTC heater fuse
30 A
5
A/C compressor fuse
30 A

[4WD]
•
It works as the power distributor to connect the high voltage battery power to front high voltage components (inverter, A/C compressor, PTC heater, etc.).
•
It is installed in front inverter assembly and includes bus bar and quick charge relay (+, -).

Battery Control System (Long Range) — High Voltage Distributing System / Front High Voltage Junction Box / Description and Operation / Description illustration

NO
System
Possible Cause
1
Battery PTC relay
Battery Management Unit (BMU) relay control
2
PTC heater fuse
30 A
3
Battery PTC fuse
20 A
4
A/C compressor fuse
30 A

Front High Voltage Junction Box Removal and Installation - 2WD

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Perform the high voltage shut off procedure.
(Refer to Battery Control System (Long Range) - "High Voltage Shut-off Procedures")
2.
Remove the front trunk.
(Refer to Body - "Front Trunk")
3.
Remove the low voltage (12 V) battery tray.
(Refer to Electric Power Conversion System - "low voltage (12 V) Battery")
4.
Disconnect the front junction box connector (A).

Battery Control System (Long Range) — High Voltage Distributing System / Front High Voltage Junction Box / Removal and Installation - 2WD / Removal illustration

5.
Disconnect the high voltage power cable (A) and battery heater connector (B).

Battery Control System (Long Range) — High Voltage Distributing System / Front High Voltage Junction Box / Removal and Installation - 2WD / Removal illustration

6.
Disconnect the PTC heater connector (A).

Battery Control System (Long Range) — High Voltage Distributing System / Front High Voltage Junction Box / Removal and Installation - 2WD / Removal illustration

7.
Disconnect the electric A/C compressor (A).

Battery Control System (Long Range) — High Voltage Distributing System / Front High Voltage Junction Box / Removal and Installation - 2WD / Removal illustration

8.
Remove the front high voltage junction box (A) after removing the nuts.

Tightening torque :
4.9 - 7.8 N·m (0.5 - 0.8 kgf·m, 3.6 - 5.8 lb·ft, 43.4 - 69.4 lb·ft)

Battery Control System (Long Range) — High Voltage Distributing System / Front High Voltage Junction Box / Removal and Installation - 2WD / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.
Note
•
Install the front high voltage junction box to the specified torque.
•
If front high voltage junction box is dropped, it may cause internal damage. (Do not reuse)

Front High Voltage Junction Box Removal and Installation - 4WD

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Perform the high voltage shut off procedure.
(Refer to Battery Control System (Long Range) - "High Voltage Shut-off Procedures")
2.
Separate the power cable fastener (A) from the body frame.

Battery Control System (Long Range) — High Voltage Distributing System / Front High Voltage Junction Box / Removal and Installation - 4WD / Removal illustration

3.
Remove the front trunk.
(Refer to Body - "Front Trunk")
4.
Disconnect the PTC heater connector (A) and battery heater connector (B).

Battery Control System (Long Range) — High Voltage Distributing System / Front High Voltage Junction Box / Removal and Installation - 4WD / Removal illustration

5.
Disconnect the high voltage junction box signal connector (A, B).

Battery Control System (Long Range) — High Voltage Distributing System / Front High Voltage Junction Box / Removal and Installation - 4WD / Removal illustration

6.
Separate the wiring protector (A) after removing the bolts.

Tightening torque :
6.9 - 9.8 N·m (0.7 - 1.0 kgf·m, 5.1 - 7.2 lb·ft)

Battery Control System (Long Range) — High Voltage Distributing System / Front High Voltage Junction Box / Removal and Installation - 4WD / Removal illustration

Battery Control System (Long Range) — High Voltage Distributing System / Front High Voltage Junction Box / Removal and Installation - 4WD / Removal illustration

7.
Remove the high voltage junction box service cover (A).

Tightening torque :
3.9 - 5.9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)

Battery Control System (Long Range) — High Voltage Distributing System / Front High Voltage Junction Box / Removal and Installation - 4WD / Removal illustration

8.
Remove the high voltage junction box ground bolts (A).

Tightening torque :
6.9 - 9.8 N·m (0.7 - 1.0 kgf·m, 5.1 - 7.2 lb·ft)

Battery Control System (Long Range) — High Voltage Distributing System / Front High Voltage Junction Box / Removal and Installation - 4WD / Removal illustration

9.
Separate the Electric A/C compressor connector (A) and fastener (B).

Battery Control System (Long Range) — High Voltage Distributing System / Front High Voltage Junction Box / Removal and Installation - 4WD / Removal illustration

10.
Separate the power cable after separating the fasteners (A).

Battery Control System (Long Range) — High Voltage Distributing System / Front High Voltage Junction Box / Removal and Installation - 4WD / Removal illustration

11.
Remove the front high voltage junction box (A).

Tightening torque :
6.9 - 9.8 N·m (0.7 - 1.0 kgf·m, 5.1 - 7.2 lb·ft)

Battery Control System (Long Range) — High Voltage Distributing System / Front High Voltage Junction Box / Removal and Installation - 4WD / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Perform the PE system leak test with the KDS.
(Refer to Front High Voltage Junction Box - "Air Tightness")
2.
Install in the reverse order of removal.
Note
•
Install the front high voltage junction box to the specified torque.
•
If front high voltage junction box is dropped, it may cause internal damage. (Do not reuse)

Front High Voltage Junction Box Air Tightness Inspection

Special Service Tool
Tool Name
Illustration
Description
EV battery pack Inspecting for air tightness tool
GIT air tightness test equipment

Battery Control System (Long Range) — High Voltage Distributing System / Front High Voltage Junction Box / Air Tightness Inspection / Special Service Tool illustration

Used for inspecting the air tightness of the Battery System Assembly (BSA) and PE system

Air Tightness Inspection
Note
•
During the high voltage junction box and multi inverter assembly (or inverter assembly (4WD)) airtightness inspection, perform it after the motor, inverter, and junction box are all assembled.
•
Perform the Power Electric (PE) system leak test procedure by using the EV battery pack tool that is for inspecting the air tightness , when working on the high voltage junction box or the inverter assembly.
•
Install in the vehicle after completing the PE system leak test procedure, when working in the motor assembly.
1.
Disconnect the PTC heater connector (A) and battery heater connector (B).

Battery Control System (Long Range) — High Voltage Distributing System / Front High Voltage Junction Box / Air Tightness Inspection illustration

2.
Install the battery heater sealing connector (P008) (A).

Battery Control System (Long Range) — High Voltage Distributing System / Front High Voltage Junction Box / Air Tightness Inspection illustration

3.
Install the PTC heater sealing connector (P001) (A).

Battery Control System (Long Range) — High Voltage Distributing System / Front High Voltage Junction Box / Air Tightness Inspection illustration

4.
Disconnect the high voltage junction box connector (A).

Battery Control System (Long Range) — High Voltage Distributing System / Front High Voltage Junction Box / Air Tightness Inspection illustration

5.
Install the high voltage junction box sealing connector (P006) (A).

Battery Control System (Long Range) — High Voltage Distributing System / Front High Voltage Junction Box / Air Tightness Inspection illustration

6.
Disconnect the electric A/C compressor (A).

Battery Control System (Long Range) — High Voltage Distributing System / Front High Voltage Junction Box / Air Tightness Inspection illustration

7.
Install the Electric A/C compressor sealing connector (P007) (A).

Battery Control System (Long Range) — High Voltage Distributing System / Front High Voltage Junction Box / Air Tightness Inspection illustration

8.
Remove the front rear under cover.
(Refer to Motor and Reduction Gear System - "Front Under Cover")
9.
Install the sealing connector (P003) (A) in the high voltage cable.

Battery Control System (Long Range) — High Voltage Distributing System / Front High Voltage Junction Box / Air Tightness Inspection illustration

10.
Install the pressure regulator adapters (A) in the pressure regulator.

Battery Control System (Long Range) — High Voltage Distributing System / Front High Voltage Junction Box / Air Tightness Inspection illustration

Note
•
Maintain the pressure by pushing the adapter with hands until starting to inspect, when installing the pressure regulator adapter.
•
Be careful not to bend the EV battery pack inspection tool hose and the pressure regulator adapter hose.
11.
Perform the PE system leak test with the KDS.
(S/W Management → Motor Control Unit → PE System leak test)
Information
Refer to the KDS screen for operating conditions and details.
12.
Check the PE system leakage.
Information
Judgment standard for PE system leakage
PASS
FAIL

Battery Control System (Long Range) — High Voltage Distributing System / Front High Voltage Junction Box / Air Tightness Inspection illustration

Battery Control System (Long Range) — High Voltage Distributing System / Front High Voltage Junction Box / Air Tightness Inspection illustration


Power Cable Components and Components Location

Component Location

Battery Control System (Long Range) — High Voltage Distributing System / Power Cable / Components and Components Location / Component Location illustration

1. Power Cable [front high voltage junction box ↔ Battery System Assembly (BSA)]
3. Charger Inlet Assembly
2. Power Cable [Integrated Charging Control Unit (ICCU) ↔ BSA]

Power Cable Removal and Installation - 2WD

Remova7
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Power cable [front high voltage junction box - Battery System Assembly (BSA)]
1.
Perform the high voltage shut off procedure.
(Refer to Battery Control System (Long Range) - "High Voltage Shut-off Procedures")
2.
Remove the front under cover.
(Refer to Motor and Reduction Gear System - "Front Under Cover")
3.
Disconnect the power cable connector (A) on the front high voltage junction box side.

Battery Control System (Long Range) — High Voltage Distributing System / Power Cable / Removal and Installation - 2WD / Remova7 illustration

Power cable [rear high voltage junction box - Battery System Assembly (BSA)]
1.
Perform the high voltage shut off procedure.
(Refer to Battery Control System (Long Range) - "High Voltage Shut-off Procedures")
2.
Remove the rear seat assembly.
(Refer to Body - "Rear Seat Assembly")
3.
Remove the cable (A) after disconnecting the Integrated Charge Control Unit (ICCU) connector.

Battery Control System (Long Range) — High Voltage Distributing System / Power Cable / Removal and Installation - 2WD / Remova7 illustration

4.
Remove the rear under cover.
(Refer to Motor and Reduction Gear System - "Rear Under Cover")
5.
Separate the cable (A) from the body by disconnecting the ICCU connector.

Battery Control System (Long Range) — High Voltage Distributing System / Power Cable / Removal and Installation - 2WD / Remova7 illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.
Note
If power cable is dropped, it may cause internal damage. (Do not reuse)

Power Cable Removal and Installation - 4WD

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Power cable [front high voltage junction box - Battery System Assembly (BSA)]
1.
Remove the front high voltage junction box.
(Refer to High Voltage Distributing System - "Front High Voltage Junction Box")
Note
It cannot separate the power cable individually due to integrated with the front high voltage junction box.
Power cable [rear high voltage junction box - Battery System Assembly (BSA)]
1.
Perform the high voltage shut off procedure.
(Refer to Battery Control System (Long Range) - "High Voltage Shut-off Procedures")
2.
Remove the rear seat assembly.
(Refer to Body - "Rear Seat Assembly")
3.
Remove the cable (A) after disconnecting the Integrated Charge Control Unit (ICCU) connector.

Battery Control System (Long Range) — High Voltage Distributing System / Power Cable / Removal and Installation - 4WD / Removal illustration

4.
Remove the rear under cover.
(Refer to Motor and Reduction Gear System - "Rear Under Cover")
5.
Separate the cable (A) from the body by disconnecting the ICCU connector.

Battery Control System (Long Range) — High Voltage Distributing System / Power Cable / Removal and Installation - 4WD / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.
Note
If power cable is dropped, it may cause internal damage. (Do not reuse)

Rear High Voltage Junction Box Description and Operation

Description
•
It works as the power distributor that connects high voltage battery power to rear high voltage components.
•
It is installed on the top of the rear wheel motor and the front of the multi-inverter assembly, and has a built-in bus bar and quick charging relays (+, -).

Battery Control System (Long Range) — High Voltage Distributing System / Rear High Voltage Junction Box / Description and Operation / Description illustration

NO
System
Possible Cause
1
Quick charge relay ( + )
Battert Management Unit (BMU) relay control
2
Quick charge relay ( - )

Rear High Voltage Junction Box Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Perform the high voltage shut off procedure.
(Refer to Battery Control System - "High Voltage Shut-off Procedures")
2.
Remove the rear cross member.
(Refer to Motor and Reduction Gear System - "Rear Under Cover")
3.
Remove the rear high voltage junction box bolt (A).

Tightening torque :
15.7 - 23.5 N·m (1.6 - 2.4 kgf·m, 11.6 - 17.4 lb·ft)

Battery Control System (Long Range) — High Voltage Distributing System / Rear High Voltage Junction Box / Removal and Installation / Removal illustration

4.
Remove the rear motor and reduction gear assembly.
(Refer to Motor and Reduction Gear System - "Rear Motor and Reduction Gear Assembly")
5.
Disconnect the rear high voltage junction box connector (A).

Battery Control System (Long Range) — High Voltage Distributing System / Rear High Voltage Junction Box / Removal and Installation / Removal illustration

6.
Separate the high voltage cable (A) from the body after removing the bolts.

Tightening torque :
15.7 - 23.5 N·m (1.6 - 2.4 kgf·m, 11.6 - 17.4 lb·ft)

Battery Control System (Long Range) — High Voltage Distributing System / Rear High Voltage Junction Box / Removal and Installation / Removal illustration

7.
Remove the high voltage junction box service cover (A).

Tightening torque :
3.9 - 5.9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)

Battery Control System (Long Range) — High Voltage Distributing System / Rear High Voltage Junction Box / Removal and Installation / Removal illustration

8.
Remove the rear high voltage junction box and inverter bolts (A).

Tightening torque :
6.9 - 9.8 N·m (0.7 - 1.0 kgf·m, 5.1 - 7.2 lb·ft)

Battery Control System (Long Range) — High Voltage Distributing System / Rear High Voltage Junction Box / Removal and Installation / Removal illustration

9.
Remove the rear high voltage junction box (A) after removing the bolts and nut.

Tightening torque
Bolt : 15.7 - 23.5 N·m (1.6 - 2.4 kgf·m, 11.6 - 17.4 lb·ft)
Nut : 17.7 - 26.5 N·m (1.8 - 2.7 kgf·m, 13.0 - 19.5 lb·ft)

Battery Control System (Long Range) — High Voltage Distributing System / Rear High Voltage Junction Box / Removal and Installation / Removal illustration

Battery Control System (Long Range) — High Voltage Distributing System / Rear High Voltage Junction Box / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.
Note
•
Install the rear high voltage junction box to the specified torque.
•
If rear high voltage junction box is dropped, it may cause internal damage. (Do not reuse)

Other information:

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Precautions for accident vehicle

Precautions for accident vehicle Electric vehicle includes a high voltage battery, which can lead to serious accidents such as short circuits or electric shocks if touched incorrectly.

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Sub-Battery Pack Assembly (Sub-BPA) Removal and Installation

Special Service Tool Tool Name / Number Illustration Description High voltage Battery Module Assembly (BMA) transport hangerTKS - 2301 Used to transferring the high voltage Sub Battery Pack Assembly (Sub-BPA) and Battery Module Assembly (BMA) High voltage battery module surface pressure jig09375 - GI800

 
Copyright © 2026 Kia EV6 Manuals ⏱ 0.0275