Kia EV6: Motor and Reduction Gear System / Motor and Reduction Gear Control System
Contents:
Motor Position and Temperature Sensor Description and Operation. Motor Position and Temperature Sensor Components and Components Location
Motor Position and Temperature Sensor Description and Operation
Motor position sensor
Accurate motor rotor absolute position detection is required for motor control.
The MCU can control the motor under optimal conditions using the position and speed of the rotor transmitted from
the resolver. The resolver is mounted on a rear plate and consists of the rotor connected with motor rotor, and stator
connected with housing. This locates the position of the rotor inside the motor, like the CMP sensor of the ICE
vehicle.
Motor temperature sensor
The motor temperature sensor is assembled on the motor coil and is responsible for sensing motor temperature
information for torque compensation and motor over-temperature protection according to temperature.
Motor Position and Temperature Sensor Components and Components Location
| Components and Components Location |
Front Motor
1. Motor Position and Temperature Sensor
Connector 1-a. 9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)
|
Rear Motor
1. Motor Position and Temperature Sensor
Connector 1-a. 9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)
|
Motor Position and Temperature Sensor Removal and Installation - Front Motor
|
•
|
When working on high voltage system, the work should be performed by technicians who have completed
the relevant training. It is because that lack of knowledge of the high voltage system can lead to
serious accidents due to electric shock or electric leakage.
|
|
•
|
When working a high-voltage system, the technician must recognized and observe "General Safety
Information and Caution". If not follow, serious accidents like electric shocks and short circuit
may be caused.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedures.
|
|
|
•
|
Use a fender cover to protect the painted surface.
|
|
•
|
Be careful not to damage the connector when disconnecting.
|
|
|
Mark all wiring and hoses to prevent incorrect connections.
|
| 1. |
Shut off the high voltage circuit.
(Refer to Motor and Reduction Gear System - "High Voltage Shut-off
Procedures")
|
| 2. |
Remove the front trunk.
(Refer to Body - "Front Trunk")
|
| 3. |
Disconnect the motor position and temperature sensor connector (A).
|
| 4. |
Slightly pull out the motor position and temperature sensor connector (A) after removing the mounting bolt.
Tightening torque :
9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)
|
|
| 5. |
Remove the motor position and temperature sensor connector (A) after disconnecting the connector.
|
| 1. |
Install in the reverse order of removal.
|
Motor Position and Temperature Sensor Removal and Installation - Rear Motor
|
•
|
When working on high voltage system, the work should be performed by technicians who have completed
the relevant training. It is because that lack of knowledge of the high voltage system can lead to
serious accidents due to electric shock or electric leakage.
|
|
•
|
When working a high-voltage system, the technician must recognize and observe "General Safety
Information and Caution". If not, serious accidents like electric shocks and short circuits may
be caused.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedures.
|
|
|
•
|
Use a fender cover to protect the painted surface.
|
|
•
|
Be careful not to damage the connector when disconnecting.
|
|
|
Mark all wiring and hoses to prevent incorrect connections.
|
| 1. |
Shut off the high voltage circuit.
(Refer to Motor and Reduction Gear System - "High Voltage Shut-off
Procedures")
|
| 2. |
Remove the rear motor and reduction gear assembly.
(Refer to Motor and Reduction Gear System - "Rear Motor and Reduction
Gear Assembly")
|
| 3. |
Disconnect the motor position and temperature sensor connector (A).
|
| 4. |
Slightly pull out the motor position and temperature sensor connector (A) after removing the mounting bolt.
Tightening torque :
9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)
|
|
| 5. |
Remove the motor position and temperature sensor connector (A) after disconnecting the connector.
|
| 1. |
Install in the reverse order of removal.
|
Motor Position and Temperature Sensor Inspection
| Front Motor Position and Temperature Sensor Inspection |
|
•
|
When working on high voltage system, the work should be performed by technicians who have completed
the relevant training. It is because that lack of knowledge of the high voltage system can lead to
serious accidents due to electric shock or electric leakage.
|
|
•
|
When working on the high-voltage system or related system, make sure that you are familiar with and
comply with the "Safety Precautions, Cautions, and Warnings." If you do not comply with the
instructions, serious accidents may occur due to electric shock or leakage.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedures.
|
|
| 1. |
Shut off the high voltage circuit.
(Refer to Motor and Reduction Gear System - "High Voltage Shut-off
Procedures")
|
| 2. |
Remove the front trunk.
(Refer to Body - "Front Trunk")
|
| 3. |
Remove the inverter assembly.
(Refer to Battery Control System - "Inverter Assembly -
4WD")
|
| 4. |
Disconnect the motor position and temperature sensor connector (A).
|
| 5. |
Check the phase resistance using a multi tester.
Item
|
Inspection area
|
Specifications
|
Remark
|
Motor temperature sensor
|
Phase resistance
|
Pin 5 - Pin 10
|
18.1 - 20.8 kΩ
|
Reference temperature : 20°C (68°F )
|
Insulation resistance
|
Pin 5 - Motor housing
|
100 MΩ or more
|
Apply DC 500 V for 5 seconds
|
Pin 5 - Motor U/ V/ W
|
Dielectric strength
|
Pin 5 - Motor housing
|
0.5 mA or less
|
Apply AC 1,800v for 1 second
|
Motor position sensor
|
Phase resistance
|
Pin 2 - Pin 7
|
16.6 Ω ±7%
|
Reference temperature : 20°C (68°F )
|
Pin 3 - Pin 8
|
58.6 Ω ±7%
|
Pin 4 - Pin 9
|
49.8 Ω ±7%
|
Insulation resistance
|
Pin 2 - Motor housing
|
100 MΩ or more
|
Apply DC 500 V for 5 seconds
|
Pin 3 - Motor housing
|
Pin 4 - Motor housing
|
|
| Initialization of Front Motor Resolver Offset Automatic Calibration
|
| 1. |
POWER "OFF" and connect the KDS to the Data Link Connector.
|
| 2. |
P range & POWER "ON" (Power button LED "Red"), Select "Vehicle S/W
Management"
|
| 3. |
Perform the "Motor Control Unit-Front" and "Initialization of Automatic Resolver Offset
Calibration" using the KDS.
|
| Rear Motor Position and Temperature Sensor Inspection |
|
•
|
When working on high voltage system, the work should be performed by technicians who have completed
the relevant training. It is because that lack of knowledge of the high voltage system can lead to
serious accidents due to electric shock or electric leakage.
|
|
•
|
When working a high-voltage system, the technician must recognize and observe "General Safety
Information and Caution". If not, serious accidents like electric shocks and short circuits may
be caused.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedures.
|
|
| 1. |
Shut off the high voltage circuit.
(Refer to Motor and Reduction Gear System - "High Voltage Shut-off
Procedures")
|
| 2. |
Remove the rear motor and reduction gear assembly.
(Refer to Motor and Reduction Gear System - "Rear Motor and Reduction
Gear Assembly")
|
| 3. |
Remove the multi inverter assembly.
(Refer to Battery Control System - "Multi Inverter
Assembly")
|
| 4. |
Disconnect the motor position and temperature sensor connector (A).
|
| 5. |
Check the phase resistance using a multi tester.
Item
|
Inspection area
|
Specifications
|
Remark
|
Motor temperature sensor
|
Phase resistance
|
Pin 5 - Pin 10
|
18.1 - 20.8 kΩ
|
Reference temperature : 20°C (68°F )
|
Insulation resistance
|
Pin 5 - Motor housing
|
100 MΩ or more
|
Apply DC 500 V for 5 seconds
|
Pin 5 - Motor U/ V/ W
|
Dielectric strength
|
Pin 5 - Motor housing
|
0.5 mA or less
|
Apply AC 1,800 V for 1 second
|
Motor position sensor
|
Phase resistance
|
Pin 2 - Pin 7
|
16.6 Ω ±7%
|
Reference temperature : 20°C (68°F )
|
Pin 3 - Pin 8
|
58.6 Ω ±7%
|
Pin 4 - Pin 9
|
49.8 Ω ±7%
|
Insulation resistance
|
Pin 2 - Motor housing
|
100 MΩ or more
|
Apply DC 500 V for 5 seconds
|
Pin 3 - Motor housing
|
Pin 4 - Motor housing
|
|
| Initialization of Rear Motor Resolver Offset Automatic Calibration
|
| 1. |
POWER "OFF" and connect the KDS to the Data Link Connector.
|
| 2. |
P range & POWER "ON" (Power button LED "Red"), Select "Vehicle S/W
Management"
|
| 3. |
Perform the "Motor Control Unit-Rear" and "Initialization of Automatic Resolver Offset
Calibration" using the KDS.
|
SBW(Shift By Wire) Actuator Components and Components Location
1. SBW (Shift By Wire) Actuator 1-a. 20.6 - 27.5 N·m
(2.1 - 2.8 kgf·m, 15.2 - 20.3 lb·ft) 2. O-ring
|
|
SBW(Shift By Wire) Actuator Removal and Installation
|
•
|
When working on high voltage system, the work should be performed by technicians who have completed
the relevant training. It is because that lack of knowledge of the high voltage system can lead to
serious accidents due to electric shock or electric leakage.
|
|
•
|
When working on the high-voltage system or related system, make sure that you are familiar with and
comply with the "Safety Precautions, Cautions, and Warnings." If you do not comply with the
instructions, serious accidents may occur due to electric shock or leakage.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedures.
|
|
| 1. |
Shut off the high voltage circuit.
(Refer to Motor and Reduction Gear System - "High Voltage Shut-off
Procedures")
|
| 2. |
Remove the rear motor and reduction gear assembly.
(Refer to Motor and Reduction Gear System - "Rear Motor and Reduction
Gear Assembly")
|
| 3. |
Separate the main wiring protector (A) after removing the bolts.
Tightening torque :
6.9 - 9.8 N·m (0.7 - 1.0 kgf·m, 5.1 - 7.2 lb·ft)
|
|
| 4. |
Disconnect the SBW (Shift By Wire) actuator connector (A).
|
| 5. |
Remove the SBW actuator (A) after removing the bolts.
Tightening torque :
20.6 - 27.5 N·m (2.1 - 2.8 kgf·m, 15.2 - 20.3 lb·ft)
|
|
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedure.
|
|
| 1. |
Install in reverse order of removal.
|
•
|
Install to the specified torque.
|
|
•
|
When installed, align the new output shaft (A) in the same position as the old output shaft
(B) of the equipment.
|
|
•
|
Do not rotate the SBW actuator output shaft under excessive force when assembling, as this
may cause damage to internal parts.limit value : -25° to +25°
|
|
|
| 2. |
Perform the order below with the KDS.
(S/W Management → SCU - SBW Control Unit (SCU) → SCU Actuator Reducer Position Learning)
|
Refer to the KDS screen for operating conditions and details
|
|
| 3. |
Perform Over The Air (OTA) controller S/W update with KDS.
(Refer to Body - "Over The Air (OTA)")
|
SBW(Shift By Wire) Lever Components and Components Location. SBW(Shift By Wire) Lever Removal and Installation
SBW(Shift By Wire) Lever Components and Components Location
1. Rear Console Cover 2. Floor Console Upper
Cover
|
3. SBW Lever
|
SBW(Shift By Wire) Lever Removal and Installation
|
When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent
damage to components.
|
| 1. |
Disconnect the battery negative ( - ) terminal and the service interlock connector.
(Refer to Battery Control System - "Auxiliary 12 V Battery -
2WD")
(Refer to Battery Control System - "Auxiliary 12 V Battery -
4WD")
|
| 2. |
Remove the floor console upper cover.
(Refer to body - "Floor Console Upper Cover")
|
| 3. |
Disconnect the dial type SBW connector (A).
|
| 4. |
Remove the dial type SBW (A) after removing the screws.
|
| 1. |
Install in the reverse order of removal.
|
Oil Temperature Sensor Specification
Item
|
Specification
|
Sensor Type
|
NTC thermistor
|
Operation Voltage (V)
|
4.75 - 5.25
|
Max current (mA)
|
100
|
Response time
|
Test medium : Coolant
|
MAX. 5 sec
|
Oil temperature [°C (°F)]
|
-40 to 150 (-40 to 302)
|
| Oil Temperature Sensor Table |
Temperature [°C (°F)]
|
Resistance (kΩ)
|
Minimum
|
Normal
|
Maximum
|
-40 (-40)
|
41.74
|
48.14
|
54.54
|
-30 (-22)
|
23.54
|
26.74
|
29.94
|
-20 (-4)
|
14.13
|
15.48
|
16.83
|
-10 (14)
|
8.393
|
9.308
|
10.223
|
0 (32)
|
5.281
|
5.790
|
6.299
|
10 (50)
|
3.422
|
3.714
|
4.007
|
20 (68)
|
2.310
|
2.450
|
2.590
|
30 (86)
|
1.554
|
1.658
|
1.762
|
40 (104)
|
1.084
|
1.148
|
1.212
|
50 (122)
|
0.7729
|
0.8126
|
0.8524
|
60 (140)
|
0.5615
|
0.5865
|
0.6115
|
70 (158)
|
0.4154
|
0.4311
|
0.4469
|
80 (176)
|
0.3122
|
0.3222
|
0.3322
|
90 (194)
|
0.2382
|
0.2446
|
0.2510
|
100 (212)
|
0.1844
|
0.1884
|
0.1924
|
110 (230)
|
0.1451
|
0.1471
|
0.1491
|
120 (248)
|
0.1139
|
0.1163
|
0.1187
|
130 (266)
|
0.0908
|
0.0930
|
0.0953
|
140 (284)
|
0.0731
|
0.0752
|
0.0773
|
150 (302)
|
0.0594
|
0.0614
|
0.0634
|
Oil Temperature Sensor Components and Components Location
1. Oil Temperature Sensor 1-a. 9.8 - 11.8 N·m (1.0 -
1.2 kgf·m, 7.2 - 8.7 lb·ft)
|
2. O-ring
|
1. Oil Temperature Sensor 1-a. 9.8 - 11.8 N·m (1.0 -
1.2 kgf·m, 7.2 - 8.7 lb·ft)
|
2. O-ring
|
Oil Temperature Sensor Removal and Installation - Front Motor
|
•
|
When working on high voltage system, the work should be performed by technicians who have completed
the relevant training. It is because that lack of knowledge of the high voltage system can lead to
serious accidents due to electric shock or electric leakage.
|
|
•
|
When working on the high-voltage system or related system, make sure that you are familiar with and
comply with the "Safety Precautions, Caution, and Warnings." If you do not comply with the
instructions, serious accidents may occur due to electric shock or leakage.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedures.
|
|
| 1. |
Disconnect the battery negative ( - ) terminal and the service interlock connector.
(Refer to Battery Control System - "Auxiliary 12 V
Battery")
|
| 2. |
Remove the front under cover.
(Refer to Front Motor and Reduction Gear System - "Front Under
Cover")
|
| 3. |
Drain the front motor and reduction gear oil.
(Refer to Front Motor and Reduction Gear System - "Front Motor and
Reduction Gear Oil")
|
| 4. |
Disconnect the oil temperature sensor connector (A).
|
| 5. |
Remove the oil temperature sensor (A) after removing the bolt.
Tightening torque :
9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)
|
|
|
•
|
When working on high voltage system, the work should be performed by technicians who have completed
the relevant training. It is because that lack of knowledge of the high voltage system can lead to
serious accidents due to electric shock or electric leakage.
|
|
•
|
When working on the high-voltage system or related system, make sure that you are familiar with and
comply with the "Safety Precautions, Cautions, and Warnings." If you do not comply with the
instructions, serious accidents may occur due to electric shock or leakage.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedures.
|
|
| 1. |
Install in the reverse order of removal.
|
The existing oil temperature sensor O-ring (A) must be replaced with a new one (do not reuse).
|
|
| 2. |
Refill the front motor and reduction gear oil.
(Refer to Front Motor and Reduction Gear System - "Front Motor and
Reduction Gear Oil")
|
Oil Temperature Sensor Removal and Installation - Rear Motor
|
•
|
When working on high voltage system, the work should be performed by technicians who have completed
the relevant training. It is because that lack of knowledge of the high voltage system can lead to
serious accidents due to electric shock or electric leakage.
|
|
•
|
When working on the high-voltage system or related system, make sure that you are familiar with and
comply with the "Safety Precautions, Cautions, and Warnings." If you do not comply with the
instructions, serious accidents may occur due to electric shock or leakage.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedures.
|
|
| 1. |
Disconnect the battery negative ( - ) terminal and the service interlock connector.
(Refer to Battery Control System - "Auxiliary 12 V Battery -
2WD")
(Refer to Battery Control System - "Auxiliary 12 V Battery -
4WD")
|
| 2. |
Remove the rear under cover.
(Refer to Motor and Reduction Gear System - "Rear Under
Cover")
|
| 3. |
Drain the rear motor and reduction gear oil.
(Refer to Rear Motor and Reduction Gear System - "Rear Motor and
Reduction Gear Oil")
|
| 4. |
Disconnect the oil temperature sensor connector (A).
|
| 5. |
Remove the oil temperature sensor (A) after removing the bolt.
Tightening torque :
9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)
|
|
|
•
|
When working on the high-voltage system, the work should be performed by technicians who have
completed the relevant training. It is because that lack of knowledge of the high voltage system can
lead to serious accidents due to electric shock or electric leakage.
|
|
•
|
When working on the high-voltage system or related system, make sure that you are familiar with and
comply with the "Safety Precautions, Caution, and Warnings." If you do not comply with the
instructions, serious accidents may occur due to electric shock or leakage.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedures.
|
|
| 1. |
Install in the reverse order of removal.
|
The existing oil temperature sensor O-ring (A) must be replaced with a new one (do not reuse).
|
|
| 2. |
Refill the rear motor and reduction gear oil.
(Refer to Rear Motor and Reduction Gear System - "Rear Motor and
Reduction Gear Oil")
|
Electronic Oil Pump (EOP) Components and Components Location
1. Electric Oil Pump (EOP) 1-a. 19.6 - 26.5 N·m (2.0
- 2.7 kgf·m, 14.5 - 19.5 lb·ft)
|
2. O-ring
|
1. Electric Oil Pump (EOP) 1-a. 19.6 - 26.5 N·m (2.0
- 2.7 kgf·m, 14.5 - 19.5 lb·ft)
|
2. O-ring
|
Electronic Oil Pump (EOP) Removal and Installation - Front Motor
|
•
|
When working on high voltage system, the work should be performed by technicians who have completed
the relevant training. It is because that lack of knowledge of the high voltage system can lead to
serious accidents due to electric shock or electric leakage.
|
|
•
|
When working on the high-voltage system or related system, make sure that you are familiar with and
comply with the "Safety Precautions, Cautions, and Warnings." If you do not comply with the
instructions, serious accidents may occur due to electric shock or leakage.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedures.
|
|
|
•
|
Use a fender cover to protect the painted surface.
|
|
•
|
Be careful not to damage the connector when disconnecting.
|
|
•
|
When disconnecting a quick connector, refer to the following according to the type of quick
connector.
- Remove while pressing the quick connector clamp (A) in the direction of the arrow.
- Do not touch the rubber seal (B) inside the hose.
|
|
| 1. |
Disconnect the battery negative ( - ) terminal and the service interlock connector.
(Refer to Battery Control System - "Auxiliary 12 V
Battery")
|
| 2. |
Remove the front under cover.
(Refer to Front Motor and Reduction Gear System - "Front Under
Cover")
|
| 3. |
Drain the coolant.
(Refer to Cooling System - "Coolant")
|
| 4. |
Drain the front motor and reduction gear oil.
(Refer to Front Motor and Reduction Gear System - "Front Motor and
Reduction Gear Oil")
|
| 5. |
Disconnect the Electronic Water Pump (EWP) quick connector hose (A).
|
| 6. |
Disconnect the Electronic Oil Pump (EOP) connector (A).
|
| 7. |
Remove the EOP (A) after removing the bolts.
Tightening torque :
19.6 - 26.5 N·m (2.0 - 2.7 kgf·m, 14.5 - 19.5 lb·ft)
|
|
|
•
|
When working on high voltage system, the work should be performed by technicians who have completed
the relevant training. It is because that lack of knowledge of the high voltage system can lead to
serious accidents due to electric shock or electric leakage.
|
|
•
|
When working on the high-voltage system or related system, make sure that you are familiar with and
comply with the "Safety Precautions, Cautions, and Warnings." If you do not comply with the
instructions, serious accidents may occur due to electric shock or leakage.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedures.
|
|
| 1. |
Install in the reverse order of removal.
|
•
|
The existing O-ring (A) must be replaced with a new one (do not reuse).
|
|
•
|
When reinstalling EOP, replace the O-ring (A) with a new one (do not reuse).
|
|
•
|
Make sure the quick connector is installed securely.
|
|
|
| 2. |
Refill the front motor and reduction gear oil.
(Refer to Front Motor and Reduction Gear System - "Front Motor and
Reduction Gear Oil")
|
| 3. |
Fill the coolant.
(Refer to Cooling System - "Coolant")
|
Electronic Oil Pump (EOP) Removal and Installation - Rear Motor
|
•
|
When working on high voltage system, the work should be performed by technicians who have completed
the relevant training. It is because that lack of knowledge of the high voltage system can lead to
serious accidents due to electric shock or electric leakage.
|
|
•
|
When working on the high-voltage system or related system, make sure that you are familiar with and
comply with the "Safety Precautions, Cautions, and Warnings." If you do not comply with the
instructions, serious accidents may occur due to electric shock or leakage.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedures.
|
|
| 1. |
Disconnect the battery negative ( - ) terminal and the service interlock connector.
(Refer to Battery Control System - "Auxiliary 12 V Battery -
2WD")
(Refer to Battery Control System - "Auxiliary 12 V Battery -
4WD")
|
| 2. |
Remove the rear under cover.
(Refer to Rear Motor and Reduction Gear System - "Rear Under
Cover")
|
| 3. |
Drain the rear motor and reduction gear oil.
(Refer to Rear Motor and Reduction Gear System - "Rear Motor and
Reduction Gear Oil")
|
| 4. |
Disconnect the Electronic Oil Pump (EOP) connector (A).
|
| 5. |
Remove the EOP (A) after removing the bolts.
Tightening torque :
19.6 - 26.5 N·m (2.0 - 2.7 kgf·m, 14.5 - 19.5 lb·ft)
|
|
|
•
|
When working on the high-voltage system, the work should be performed by technicians who have
completed the relevant training. It is because that lack of knowledge of the high voltage system can
lead to serious accidents due to electric shock or electric leakage.
|
|
•
|
When working on the high-voltage system or related system, make sure that you are familiar with and
comply with the "Safety Precautions, Cautions, and Warnings." If you do not comply with the
instructions, serious accidents may occur due to electric shock or leakage.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedures.
|
|
| 1. |
Install in the reverse order of removal.
|
•
|
The existing O-ring (A) must be replaced with a new one (do not reuse).
|
|
•
|
When reinstalling EOP, replace the O-ring (A) with a new one (do not reuse).
|
|
|
| 2. |
Refill the rear motor and reduction gear oil.
(Refer to Rear Motor and Reduction Gear System - "Rear Motor and
Reduction Gear Oil")
|
Disconnect Actuator System (DAS) Motor Components and Components Location. Disconnect Actuator System (DAS) Motor Description and Operation
Disconnect Actuator System (DAS) Motor Components and Components Location
| Components and Components Location |
1. Disconnect Actuator System (DAS) Motor 1-a. 4.9 -
5.9 N·m (0.5 - 0.6 kgf·m, 3.6 - 4.3 lb·ft, 43.4 - 52.1 lb·in)
|
2. O-ring
|
Disconnect Actuator System (DAS) Motor Description and Operation
The 4WD system improves driving performance but also reduce driving range.
To compensate for shortening range, 2WD drive (rear-wheel motor and reduction gear) is applied depending on driving
conditions and *DAS is applied to cut off the drive line to reduce front-wheel motor and reduction gear line
resistance.
The actuator (DAS motor) installed for controlling the DAS, The DAS motor takes the VCU signal and connects or
disconnects the deceleration gear and the driveshaft.
*DAS : Disconnect Actuator System
*VCU : Vehicle Control Unit
DAS Component
DAS Motor Operating Conditions by Driving Condition
Item
|
2WD → 4WD
|
4WD → 2WD
|
Drive mode
|
SNOW, SPORT MODE
|
※ If the conditions on the left are not met and the conditions below are met
| 1) |
ECO MODE
[However, if the vehicle speed is less than 9 mph (15 km/h), it will be connected]
|
|
Rapid steering
|
Steering angle more than 60° , and angular acceleration 40°/sec
|
Driving at gradient
|
Gradient more than 8%
|
Vehicle speed [kph (mph)]
|
15 (9.3) or slower, 120 (74.5) or faster (Normal mode only)
|
The driver's will for acceleration.
|
When the torque required by the driver is greater than the maximum torque of the rear wheels.
|
Electronic brake actuation.
|
When TCS, ESC operate.
|
Disconnect Actuator System (DAS) Motor Removal and Installation
|
•
|
When working on high voltage system, the work should be performed by technicians who have completed
the relevant training. It is because that lack of knowledge of the high voltage system can lead to
serious accidents due to electric shock or electric leakage.
|
|
•
|
When working on the high-voltage system or related system, make sure that you are familiar with and
comply with the "Safety Precautions, Cautions, and Warnings." If you do not comply with the
instructions, serious accidents may occur due to electric shock or leakage.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedures.
|
|
| 1. |
Disconnect the battery negative ( - ) terminal and the service interlock connector.
(Refer to Battery Control System - "Auxiliary 12 V
Battery")
|
| 2. |
Remove the front under cover.
(Refer to Front Motor and Reduction Gear System - "Front Under
Cover")
|
| 3. |
Disconnect the Disconnect Actuator System (DAS) motor connector (A).
|
| 4. |
Remove the DAS motor (A) after removing the hexagon socket head bolts.
Tightening torque :
4.9 - 5.9 N·m (0.5 - 0.6 kgf·m, 3.6 - 4.3 lb·ft, 43.4 - 52.1 lb·in)
|
|
|
•
|
When working on high voltage system, the work should be performed by technicians who have completed
the relevant training. It is because that lack of knowledge of the high voltage system can lead to
serious accidents due to electric shock or electric leakage.
|
|
•
|
When working on the high-voltage system or related system, make sure that you are familiar with and
comply with the "Safety Precautions, Cautions, and Warnings." If you do not comply with the
instructions, serious accidents may occur due to electric shock or leakage.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedures.
|
|
| 1. |
Install in the reverse order of removal.
|
The existing O-ring (A) must be replaced with a new one (do not reuse).
|
|
Vehicle Control Unit (VCU) Description and Operation
|
•
|
Vehicle Control Unit (VCU) is the top-level controller of the vehicle that combines all the information to
meet the driver's needs.
|
|
•
|
VCU comprehensively controls Drive motor control, Air conditioning load control, 12 V electric load power
supply control, Disconnect Actuator System (DAS), and others.
|
Function
|
Detail
|
Drive Motor Control
|
|
•
|
Calculate usable battery power
|
|
•
|
Calculate usable motor toque
|
|
•
|
Order motor torque considering Driver demands (APS, Brake SW, Shift lever)
|
|
A/C Load Control
|
|
•
|
Order the final FATC permission power by using the battery information and FATC request power data.
|
|
12 V Electric Load Power Supply Control
|
|
•
|
LDC operation mode is determined according to 12 V battery information and vehicle status.
|
|
Disconnect Actuator System (DAS) Motor
|
|
•
|
As DAS is applied to 4WD vehicles, it controls the connection or disconnection between the front
wheel motor and drive shafts depending on the driving condition.
|
|
Cluster control
|
|
•
|
Command to indicate Drive Power, Energy Flow, Service lamp & various lamp lighting.
|
|
Distance to Empty (DTE)
|
|
•
|
Command to indicates usable battery energy and distance to empty based on prior drive pattern.
|
|
•
|
If drive path is set by using AVNT, DTE accuracy is improved by estimating the energy consumption
to destination.
|
|
Booking / Remote control
|
|
•
|
Remote control through a smartphone linked with Kia connect
|
|
•
|
Reservation Function through operation time setting by driver.
|
|
Regenerative braking control
|
|
•
|
Calculate motor charge torque command for regenerative braking.
|
|
•
|
Calculate regenerative brake force.
|
|
Vehicle Control Unit (VCU) Components and Components Location
1. Auxiliary 12 V Battery Negative ( - ) Cable 1-a.
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft) 2. Auxiliary 12 V Battery Positive ( + ) Cable 2-a. 7.8 -
9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft) 3. Battery Clamp 3-a. 9.8 - 13.7 N·m (1.0 - 1.4 kgf·m, 7.2 -
10.1 lb·ft)
|
4. Auxiliary 12 V Battery 5. Vehicle Control Unit
(VCU) 5-a. 9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft) 6. Battery Tray 6-a. 9.8 - 13.7 N·m (1.0 -
1.4 kgf·m, 7.2 - 10.1 lb·ft)
|
Vehicle Control Unit (VCU) Removal and Installation - 2WD
|
•
|
When working on high voltage system, the work should be performed by technicians who have completed
the relevant training. It is because that lack of knowledge of the high voltage system can lead to
serious accidents due to electric shock or electric leakage.
|
|
•
|
When working a high-voltage system, the technician must recognize and observe "General Safety
Information and Caution". If not, serious accidents like electric shocks and short circuits may
be caused.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedures.
|
|
| 1. |
Remove the auxiliary 12 V battery.
(Refer to Battery Control System - "Auxiliary 12 V
Battery")
|
| 2. |
Disconnect the Vehicle Control Unit (VCU) connector (A).
|
| 3. |
Remove the VCU assembly (A) after removing the bolts.
Tightening torque :
9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)
|
|
| 4. |
Separate the bracket from the VCU (A) by removing the bolts.
Tightening torque :
9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)
|
|
|
•
|
When working on high voltage system, the work should be performed by technicians who have completed
the relevant training. It is because that lack of knowledge of the high voltage system can lead to
serious accidents due to electric shock or electric leakage.
|
|
•
|
When working a high-voltage system, the technician must recognize and observe "General Safety
Information and Caution". If not, serious accidents like electric shocks and short circuits may
be caused.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedures.
|
|
| 1. |
Install in the reverse order of removal.
|
•
|
Install the Vehicle Control Unit (VCU) to the specified torque values.
|
|
•
|
If the VCU drops, it may cause internal damage. Replace it with a new one. (Don't
reuse)
|
|
|
| 2. |
Perform the Write VIN procedures with the KDS.
(S/W Management → Vehicle Control Unit → Write VIN)
|
Vehicle Control Unit (VCU) Removal and Installation - 4WD
|
•
|
When working on high voltage system, the work should be performed by technicians who have completed
the relevant training. It is because that lack of knowledge of the high voltage system can lead to
serious accidents due to electric shock or electric leakage.
|
|
•
|
When working a high-voltage system, the technician must recognize and observe "General Safety
Information and Caution". If not, serious accidents like electric shocks and short circuits may
be caused.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedures.
|
|
| 1. |
Remove the auxiliary 12 V battery.
(Refer to Battery Control System - "Auxiliary 12 V
Battery")
|
| 2. |
Disconnect the Vehicle Control Unit (VCU) connector (A).
|
| 3. |
Separate the wiring (A) fastened to the VCU bracket.
|
| 4. |
Remove the VCU assembly (A) after removing the bolts.
Tightening torque :
9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)
|
|
| 5. |
Separate the bracket from the VCU (A) by removing the bolts.
Tightening torque :
9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)
|
|
|
•
|
When working on high voltage system, the work should be performed by technicians who have completed
the relevant training. It is because that lack of knowledge of the high voltage system can lead to
serious accidents due to electric shock or electric leakage.
|
|
•
|
When working a high-voltage system, the technician must recognize and observe "General Safety
Information and Caution". If not, serious accidents like electric shocks and short circuits may
be caused.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedures.
|
|
| 1. |
Install in the reverse order of removal.
|
•
|
Install the Vehicle Control Unit (VCU) to comply with the specified torque values.
|
|
•
|
If the VCU drops, it may cause internal damage. Replace it with a new one. (Don't
reuse)
|
|
|
| 2. |
Perform the Write VIN procedures with the KDS.
(S/W Management → Vehicle Control Unit → Write VIN)
|
Accelerator Pedal Module Specification
Accelerator Pedal Position
|
Output Voltage (V)
|
APS 1
|
APS 2
|
Idle Stroke
|
0.7 - 0.8
|
0.33 - 0.43
|
Full Stroke
|
3.98 - 4.22
|
1.93 - 2.17
|
Accelerator Pedal Module On Vehicle Inspection
| 1. |
Diagnostic equipment (KDS) can be used to diagnose faulty parts quickly. (Refer to "DTC Diagnostic
Guide")
| (1)
|
Self diagnosis : Inspection and display failed code (DTC)
|
| (2)
|
Sensor data : Checking the system input/output values
|
| (3)
|
Forced operation : Checking the system operation condition
|
| (4)
|
Additional function : Controlling other features including system option setting and zero point
adjustment
|
|
| 1. |
Checks the output voltage of the sensor 1 and sensor 2 according to accelerator pedal state by using a KDS.
Accelerator Pedal Position
|
Output Voltage (V)
|
APS 1
|
APS 2
|
Idle Stroke
|
0.7 - 0.8
|
0.33 - 0.43
|
Full Stroke
|
3.98 - 4.22
|
1.93 - 2.17
|
|
Accelerator Pedal Module Removal and Installation
| 1. |
Disconnect the battery negative ( - ) terminal and the service interlock connector.
(Refer to Battery Control System - "Auxiliary 12 V Battery -
2WD")
(Refer to Battery Control System - "Auxiliary 12 V Battery -
4WD")
|
| 2. |
Disconnect the connector (A).
|
| 3. |
Remove the accelerator pedal module (A) after removing the nuts.
Tightening torque :
12.7 - 15.7 N·m (1.3 - 1.6 kgf·m, 9.4 - 11.6 lb·ft)
|
|
| 1. |
Install in the reverse order of removal.
|
•
|
Install the accelerator pedal module to comply with the specified torque values.
|
|
•
|
If the accelerator pedal module drops, it may cause internal damage. Replace it with a new
one. (Don't resue)
|
|
|
Other information:
Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Wiper Blades
When the windshield wipers no longer clean the windshield effectively, the wiper blades may be worn, hardened,
cracked, or damaged and should be replaced.
To prevent damage to the wiper mechanism, wiper arms, or related components, never move the wiper blades
manually.
The use of non-approved wiper blades on the Kia EV6 may lead to poor wiping performance, excessive noise, or
premature failure.
Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Linking and unlinking profile
How to link user profile
Open the infotainment settings menu and select Setup > User profile > Profile
setting > Link Digital Key (Smartphone) to begin the Kia EV6 profile
linking process.
After selecting Link, the digital key associated with the registered smartphone number and its [Group]
will
connect to the chosen user profile.