Kia EV6: Suspension System / Wheel and Tire

Contents:

Tire Inspection

Tire Wear
1.
Measure the tread depth of the tires.

Tread depth [Limit] :
1.6 mm (0.062 in.) (High Speed Vehicle : 2.4 mm (0.09 in.)

2.
If the remaining tread depth (A) is less than the limit, replace the tire.

Suspension System — Wheel and Tire / Tire / Inspection / Tire Wear illustration

Note
If the tread depth is less than 1.6 mm (High Speed Vehicle: 2.4 mm (0.09 in.) the wear indicator (B) appears.

Tire Removal

Removal
1.
Remove the wheels and tires.
(Refer to Wheel and Tire - "Wheel")
2.
Deflate the tires.
3.
Remove the tire from the wheel using the tire replacing equipment.

Suspension System — Wheel and Tire / Tire / Removal illustration

Note
•
Make sure the bead breaker is sufficiently separated from the TPMS sensor.
•
Remove the bead at away 90º, 180º, and 270º from the valve.
4.
Remove the tire by levering it and rotating the wheel clockwise.

Suspension System — Wheel and Tire / Tire / Removal illustration

Suspension System — Wheel and Tire / Tire / Removal illustration

Note
•
Set the TPMS sensor at 12 o'clock from the head of the tire changer.
•
When lifting the bead with the lever, make sure that the sensor is not impacted.

Tire Installation

Installation
1.
Lubricate the tire bead side using tire mounting lubricant.

Lubricant :
Soapy water or YH 100 (Tire Lubricants)

Suspension System — Wheel and Tire / Tire / Installation illustration

2.
Place the TPMS sensor at 5 o'clock position from the tire replacing machine head for installing the bottom bead.

Suspension System — Wheel and Tire / Tire / Installation illustration

3.
Rotate the rim clockwise, and push down on the tire at the 3 o’clock position to install the bottom bead.

Suspension System — Wheel and Tire / Tire / Installation illustration

Note
Install the tire on the wheel so that the bead touches the rim edge (6 o'clock direction) behind the sensor.
4.
Push down the tire at 3 o'clock position and then rotate the rim clockwise to install the upper bead.

Suspension System — Wheel and Tire / Tire / Installation illustration

5.
Inflate the tire until the beads fit.

Suspension System — Wheel and Tire / Tire / Installation illustration

Tire Pressure
Tire
Front
Rear
235/55 R19
250 - 255 kPa (36 - 37 psi)
255/45 R20

6.
Install the wheels and tires.
(Refer to Wheel and Tire - "Wheel")

Tire Replacement

Tire Rotation
Note
Changing directional or asymmetric tires left/right and diagonally may result in poor driving and braking performance.
Replace the tire in the direction shown by the arrow in the figure below.

Suspension System — Wheel and Tire / Tire / Replacement / Tire Rotation illustration

Rotating For Pull And Wander
If the vehicle is pulled to one side without any particular symptoms of failure, tire wear may be the cause.
In this case, the following tire replacement procedures shall be performed out.
1.
Rotate the front right and front left tires, and perform a road test in order to confirm vehicle stability.

Suspension System — Wheel and Tire / Tire / Replacement / Tire Rotation illustration

2.
If the steering pulls to the opposite side, rotate the front and rear tires, and perform a road test again.

Suspension System — Wheel and Tire / Tire / Replacement / Tire Rotation illustration

3.
If the steering continues to pull to one side, rotate the front right and left tires again, and perform a road test.

Suspension System — Wheel and Tire / Tire / Replacement / Tire Rotation illustration

4.
If the steering continues to pull to the opposite side, replace the front wheels with new ones.

Suspension System — Wheel and Tire / Tire / Replacement / Tire Rotation illustration

Wheel Removal and Installation

Removal
1.
Remove the wheel and tire (A) after removing the nuts.

Tightening torque :
107.9 - 127.5 N·m (11.0 - 13.0 kgf·m, 79.6 - 94.0 lb·ft)

[Front]

Suspension System — Wheel and Tire / Wheel / Removal and Installation / Removal illustration

[Rear]

Suspension System — Wheel and Tire / Wheel / Removal and Installation / Removal illustration

Note
Be careful not to damage the hub bolts (A) when removing the wheel and tires.
[Front]

Suspension System — Wheel and Tire / Wheel / Removal and Installation / Removal illustration

[Rear]

Suspension System — Wheel and Tire / Wheel / Removal and Installation / Removal illustration

Installation
1.
Install the wheel and tire (A) after tightening the nuts.

Tightening torque :
107.9 - 127.5 N·m (11.0 - 13.0 kgf·m, 79.6 - 94.0 lb·ft)

[Front]

Suspension System — Wheel and Tire / Wheel / Removal and Installation / Installation illustration

[Rear]

Suspension System — Wheel and Tire / Wheel / Removal and Installation / Installation illustration

Note
•
Be careful not to damage the hub bolts (A) when installing the wheel and tires.
[Front]

Suspension System — Wheel and Tire / Wheel / Removal and Installation / Installation illustration

[Rear]

Suspension System — Wheel and Tire / Wheel / Removal and Installation / Installation illustration

•
Tighten the hub nuts as follows.

Suspension System — Wheel and Tire / Wheel / Removal and Installation / Installation illustration

•
Clean the wheel side (A) and hub side (B) rust or debris prior to installing the wheels and tires.

Suspension System — Wheel and Tire / Wheel / Removal and Installation / Installation illustration

[Front]

Suspension System — Wheel and Tire / Wheel / Removal and Installation / Installation illustration

[Rear]

Suspension System — Wheel and Tire / Wheel / Removal and Installation / Installation illustration

Wheel Inspection. Wheel Balance Inspection

Wheel Inspection

Wheel Run-out Inspection
1.
Jack up the vehicle and support with a jack securely.
2.
Measure the wheel Run-out by using a dial indicator as illustration below.
Standard
Radial direction
Axial direction
Run-out
Aluminium Wheel
0.3 mm (0.0118 in.)
0.3 mm (0.0118 in.)

Suspension System — Wheel and Tire / Wheel / Inspection / Wheel Run-out Inspection illustration

3.
If measured value exceeds the standard value, replace the wheel.

Wheel Balance Inspection

Inspection
Wheel balance needs to be adjusted if the tires are unbalanced or after tire replacement or maintenance work has been performed.

Maximum rim unbalance weight : 2.12 oz (60 g)

Suspension System — Wheel and Tire / Wheel Balance / Inspection illustration

Note
•
If the maximum unbalance weight over than 3.53 oz (100g), reassemble the wheel and tire, then perform the wheel balance adjustment.
•
Make sure that the wheel and tire install in the balancer securely.
•
For details, refer to the instructions of each balancer.
•
Use flange type balance lead (A) or flat type balance lead (B) depending on wheel flange type.

Suspension System — Wheel and Tire / Wheel Balance / Inspection illustration

Other information:

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: A Guide to Storage, Transport and Disposal of Old Battery Systems

Used high voltage battery system storage, transportation, disposal guide • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training.

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Towing

Towing Service Wheel dollies If the Kia EV6 requires towing, the procedure should be performed by an authorized Kia dealer or a professional towing service equipped to handle electric vehicles. Following the correct lifting and transportation procedures is essential to prevent damage to the electric powertrain, suspension, battery system, and drivetrain components.

Contents

Categories

 
Copyright © 2026 Kia EV6 Manuals � 0.0225