Kia EV6: Brake System / Brake bleeding

Special Service Tool
Tool Name / Number
Illustration
Description
Air bleeding tool
0K580 - 3D100

Brake System — Brake bleeding / Special Service Tool illustration

Used for brake bleeding (regulating pressure)
(Used with 0K585 - E8100)
Air bleeding tool adaptor
0K585 - E8100

Brake System — Brake bleeding / Special Service Tool illustration

Used for brake bleeding (reservoir cap adapter)
(Used with 0K580 - 3D100)

Integrated Electronic Brake (IEB) System Air Bleeding procedures
Note
•
Do not reuse the drained brake fluid.
•
Always use genuine DOT4 brake Fluid, Using a non-genuine DOT4 brake fluid can cause corrosion and decrease the life of the system.
•
Before opening the reservoir tank cap, clean any debris or material around.
•
Make sure that no dirt or other foreign matter is allowed to contaminate the brake fluid.
•
Be careful not to get brake fluid on the body or vehicle and, if so, wipe immediately with a clean cloth.
•
Fill the brake fluid during air bleeding to prevent the brake fluid level from falling below the 'MIN' line.
•
Close the SST's air shut-off valve first before opening the brake reservoir cap to fill the brake fluid.
1.
Disconnect the battery negative ( - ) terminal and the service interlock connector.
(Refer to Battery Control System - "Auxiliary 12 V Battery - 2WD")
(Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
2.
Close the air shut-off valve (A) and install the plug (B) before installing the SST (09580 - 3D100).

Brake System — Brake bleeding / Special Service Tool illustration

Note
•
Make sure that the plug (B) is securely installed for accurate setting of the pressure regulator and safety.
•
To avoid damaging the brake reservoir, and to ensure safety, set the pressure regulator (B) to 2 - 3 bar.
3.
Connect the air hose (A), and open the air shut-off valve slowly to set the pressure gauge (B) to specified value.

Pressure : 2 - 3 bar

Brake System — Brake bleeding / Special Service Tool illustration

4.
Close the air shut-off valve (A), and then remove the plug (B).

Brake System — Brake bleeding / Special Service Tool illustration

Caution
If the plug (B) is removed while the air shut-off valve (A) is open, injury can occur by the hose.
5.
Remove the brake reservoir cap (A).

Brake System — Brake bleeding / Special Service Tool illustration

6.
Fill the brake fluid to the 'MAX' line.

Specification : DOT 4
Capacity :
As required [About (339 - 379 cc)]

7.
Install the SST (0K585 - E8100) to the reservoir tank.

Brake System — Brake bleeding / Special Service Tool illustration

8.
Install the SST (09580 - 3D100) to the adapter.

Brake System — Brake bleeding / Special Service Tool illustration

9.
Install the air hose (A) to the SST (09580 - 3D100), and then pressurize to the specified pressure.

Specification : 2 - 3 bar

Brake System — Brake bleeding / Special Service Tool illustration

10.
Open each brake bleed screw (A), drain the brake fluid for about 20 seconds,and then close the bleed screw.

Tightening torque :
Front : 6.9 - 12.7 N·m (0.7 - 1.3 kgf·m, 5.1 - 9.4 lb·ft, 60.8 - 112.8 lb·in)
Rear : 13.7 - 19.6 N·m (1.4 - 2.0 kgf·m, 10.1 - 14.5 lb·ft)

Note
•
Following order : RR → RL → FL → FR
•
If the brake fluid level falls below the 'MIN' line during air bleed, remove the pressurizing equipment and refill with brake fluid. Then reinstall the pressurizing equipment and continue air bleeding.
•
Bleed the air until there is no air in the brake fluid.
•
Be careful not to open the bleed screw too much. Air backflow may occur.
•
Do not press the brake pedal without entering IEB air bleeding mode. The IEB may be damaged.
[Front]

Brake System — Brake bleeding / Special Service Tool illustration

[Rear]

Brake System — Brake bleeding / Special Service Tool illustration

11.
Close the air shut-off valve (A), remove the air hose (B), and open the valve slowly to drain the air.

Brake System — Brake bleeding / Special Service Tool illustration

12.
Remove the air hose (A) from the SST (09580 - 3D100).

Brake System — Brake bleeding / Special Service Tool illustration

13.
Remove the SST (09580 - 3D100).00).

Brake System — Brake bleeding / Special Service Tool illustration

14.
Remove the SST (0K585 - E8100).

Brake System — Brake bleeding / Special Service Tool illustration

15.
Fill the brake fluid to the 'MAX' line.

Specification : DOT 4
Capacity :
As required [About (339 - 379 cc)]

16.
Connect the battery negative ( - ) terminal and connect the service interlock connector.
(Refer to Battery Control System - "Auxiliary 12 V Battery - 2WD")
(Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
Information
If all of the conditions below are satisfied, the subsequent steps can be omitted.
•
If there is no air in the brake line.
•
If the IEB unit is not replaced.
•
If the reservoir tank is not replaced.
1.
Enter the IEB air bleeding mode.
(1)
Before entering the IEB air bleeding mode, check the vehicle for ABS/ESC-related DTCs.
Note
If DTCs are present, it is not possible to enter the IEB air bleeding mode.
(2)
Turn on the vehicle, align the steering wheel, then set the gear knob to "P".
Note
Press the brake pedal as little as possible for turning on the vehicle.
(3)
Press and release the brake pedal 10 times while pushing ESC OFF switch (A).
Note
•
Make sure to press the brake pdal more than 40 mm (1.57 in.) and release it fully to be pressed less than 10 mm (0.39 in.).
•
IEB may make an operation sound while entering IEB air bleeding mode.
(4)
Turn off and on the vehicle, then press the ESC OFF switch (A) once.

Brake System — Brake bleeding / Special Service Tool illustration

Note
Press the brake pedal as little as possible for turning on the vehicle.
(5)
If the entry into the air bleeding mode is successful, the 3 lights below are turned on.

Illuminated :
ABS warning light (A), Parking brake/brake warning light (B), ESC OFF warning light (C)

Brake System — Brake bleeding / Special Service Tool illustration

Note
•
If the warning light does not turn on, go back to the step (1) and retry it again.
•
Entering air bleed mode must be done whithin 30 seconds.
•
If warning light turns off during air bleeding, stop the air bleeding immediately. and enter the air bleeding mode again.
•
The air bleeding mode is cancelled in each following condition.
1. IG OFF or shift lever knob in D/R/N
2. Detecting DTC
3. Turn off the ESC OFF mode
2.
Fill the brake fluid to the 'MAX' line.

Specification : DOT 4
Capacity :
As required [About (339 - 379 cc)]

3.
Press the brake pedal hard twice and open the bleed screw (A) while the brake pedal is pressed to drain the brake fluid. Repeat this procedure 10 times on each caliper.

Tightening torque :
Front : 6.9 - 12.7 N·m (0.7 - 1.3 kgf·m, 5.1 - 9.4 lb·ft, 60.8 - 112.8 lb·in)
Rear : 13.7 - 19.6 N·m (1.4 - 2.0 kgf·m, 10.1 - 14.5 lb·ft)

Note
•
Following order : RR → RL → FL → FR
•
If the brake fluid level falls below the 'MIN' line during air bleed, refill with brake fluid. Then continue the air bleeding.
•
Bleed the air until there is no air in the brake fluid.
•
Be careful not to open the bleed screw too much, air backflow may occur.
[Front]

Brake System — Brake bleeding / Special Service Tool illustration

[Rear]

Brake System — Brake bleeding / Special Service Tool illustration

4.
Turn off the vehicle to exit the IEB air bleeding mode and turn on the vehicle again to check for warning lights in the cluster.
Note
If the warning light illuminates, inspect the related system.
5.
Fill the brake fluid to the 'MAX' line.

Specification : DOT 4
Capacity :
As required [About (339 - 379 cc)]

6.
Install the brake reservoir cap (A).

Brake System — Brake bleeding / Special Service Tool illustration

7.
If the air is still in the brake fluid, re-try the above procedures.

Other information:

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Tilt and telescopic steering wheel

The Kia EV6 is equipped with a tilt and telescopic steering wheel system that allows the driver to customize the steering wheel position before driving for improved comfort, visibility, and control. You can also raise or reposition the steering wheel to create additional legroom when entering or exiting the Kia EV6, making everyday use more convenient and comfortable.

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Brake Fluid Repair procedures

Inspection 1. Check the brake fluid level. Be careful as brake fluid can hurt your hands and eyes and damage painted surfaces.

Categories

 
Copyright © 2026 Kia EV6 Manuals ⏱ 0.0095