Kia EV6: Brake System / Brake System

Contents:

Inspection. Brake Line Components and Components Location

Inspection

Operation and Leakage Check
Component
Procedure
Integrated Electronic Brake [IEB](A)
Check brake operation by applying the brakes during a test drive. If the brakes do not work properly, check the IEB. Replace the IEB as an assembly if it does not work properly or if there are signs of leakage.
Brake hose (B)
Observe damage or fluid leakage.
Replace the brake hose with a new one if it is damaged or leaking.
Caliper piston seal and piston boots (C)
Check brake operation by applying the brakes. and look for damage or signs of fluid leakage.
If the pedal does not work properly, the brakes drag, or there is damage or signs of fluid leakage, disassemble and inspect the brake caliper. Replace the boots and seals with new ones whenever the brake caliper is disassembled.

Brake System — Brake System / Inspection / Operation and Leakage Check illustration

Brake Line Components and Components Location

Component

Brake System — Brake System / Brake Line / Components and Components Location / Component illustration

1. Integrated Electronic Brake (IEB) Flare Nuts 12.7 - 16.7 N·m (1.3 - 1.7 kgf·m, 9.4 - 12.3 lb·ft)
2. Engine Room Brake Line Flare Nut 12.7 - 16.7 N·m (1.3 - 1.7 kgf·m, 9.4 - 12.3 lb·ft)
3. Engine Room Brake Line Bracket Bolt 7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)
4. Front Brake Hose Bolt 24.5 - 29.4 N·m (2.5 - 3.0 kgf·m, 18.1 - 21.7 lb·ft)
5. Front Brake Line Flare Nut 13.7 - 16.7 N·m (1.4 - 1.7 kgf·m, 10.1 - 12.3 lb·ft)
6. Rear Brake Hose Bolt 24.5 - 29.4 N·m (2.5 - 3.0 kgf·m, 18.1 - 21.7 lb·ft)
7. Rear Brake Line Flare Nut 13.7 - 16.7 N·m (1.4 - 1.7 kgf·m, 10.1 - 12.3 lb·ft)

Brake Line Removal and Installation

Removal
Front brake line
1.
Disconnect the battery negative ( - ) terminal and the service interlock connector.
(Refer to Battery Control System - "Auxiliary 12 V Battery - 2WD")
(Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
2.
Remove the reservoir cap (A) and then remove brake fluid from the reservoir tank using a suitable tool.

Brake System — Brake System / Brake Line / Removal and Installation / Removal illustration

Note
Be careful not to spill brake fluid onto the vehicle or body. If brake fluid leaks, wash off with water and remove with a clean cloth as soon as possible.
Caution
When opening the tank cap, make sure there is no dust or other foreign substances to contaminate the brake fluid.
3.
Remove the front wheel and tires.
(Refer to Suspension System - "Wheel")
4.
Separate the front wheel speed sensor harness (A) from the brake line bracket.

Brake System — Brake System / Brake Line / Removal and Installation / Removal illustration

5.
Remove the brake line bracket (A) after removing the bolt.

Tightening torque :
19.6 - 29.4 N·m (2.0 - 3.0 kgf·m, 14.5 - 21.7 lb·ft)

Brake System — Brake System / Brake Line / Removal and Installation / Removal illustration

6.
Remove the brake line flare nut (B) to separate the brake line after removing the brake hose clip (A).

Tightening torque :
13.7 - 16.7 N·m (1.4 - 1.7 kgf·m, 10.1 - 12.3 lb·ft)

Brake System — Brake System / Brake Line / Removal and Installation / Removal illustration

Information
•
If the extension wrench (A) is used to tighten the flare nut, refer to the below formula and calculate the true torque.

Brake System — Brake System / Brake Line / Removal and Installation / Removal illustration

•
True torque = Torque wrench dial reading

Brake System — Brake System / Brake Line / Removal and Installation / Removal illustration

•
True torque = [(A + B) / A] × Torque wrench reading

Brake System — Brake System / Brake Line / Removal and Installation / Removal illustration

7.
Remove the brake hose (A) after removing the bolt.

Tightening torque :
24.5 - 29.4 N·m (2.5 - 3.0 kgf·m, 18.1 - 21.7 lb·ft)

Brake System — Brake System / Brake Line / Removal and Installation / Removal illustration

Note
Do not reuse the washer (B) when installing the brake hose.
Rear Brake Line
1.
Disconnect the battery negative ( - ) terminal and the service interlock connector.
(Refer to Battery Control System - "Auxiliary 12 V Battery - 2WD")
(Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
2.
Remove the reservoir cap (A) and then clean brake fluid from the reservoir tank using a suitable tool.

Brake System — Brake System / Brake Line / Removal and Installation / Removal illustration

Note
Be careful not to spill brake fluid onto the vehicle or body. If brake fluid leaks, wash off with water and remove with a clean cloth as soon as possible.
Caution
When opening the tank cap, make sure there is no dust or other foreign substances to contaminate the brake fluid.
3.
Remove the rear wheel and tires.
(Refer to Suspension System - "Wheel")
4.
Remove the brake line flare nut (B) to separate the brake line after removing the brake hose clip (A).

Tightening torque :
13.7 - 16.7 N·m (1.4 - 1.7 kgf·m, 10.1 - 12.3 lb·ft)

Brake System — Brake System / Brake Line / Removal and Installation / Removal illustration

Information
•
If the extension wrench (A) is used to tighten the flare nut, refer to the below formula and calculate the true torque.

Brake System — Brake System / Brake Line / Removal and Installation / Removal illustration

•
True torque = Torque wrench dial reading

Brake System — Brake System / Brake Line / Removal and Installation / Removal illustration

•
True torque = [(A + B) / A] × Torque wrench reading

Brake System — Brake System / Brake Line / Removal and Installation / Removal illustration

5.
Remove the brake hose (A) after removing the bolt.

Tightening torque :
24.5 - 29.4 N·m (2.5 - 3.0 kgf·m, 18.1 - 21.7 lb·ft)

Brake System — Brake System / Brake Line / Removal and Installation / Removal illustration

Note
Do not reuse the washer (B) when installing the brake hose.
Installation
1.
Install in the reverse order of removal.
Note
Check the brake fluid level sensor connector (A) is securely installed. Incorrect installation may cause the brake warning lamp to illuminate.
2.
Fill the brake reservoir with brake fluid and perform air bleeding.
(Refer to Brake System - "Brake Bleeding")

Brake Line Inspection. Brake Pedal Components and Components Location

Brake Line Inspection

Inspection
1.
Check the brake line and hose for crack or corrosion.
2.
Check the line flare nuts for damage.

Brake Pedal Components and Components Location

Component

Brake System — Brake System / Brake Pedal / Components and Components Location / Component illustration

1. Brake Pedal Arm
1-a. 24.5 - 34.3 N·m (2.5 - 3.5 kgf·m, 18.1 - 25.3 lb·ft)
2. Brake Pedal Pad
3. Return Spring
4. Stopper

5. Stop Lamp Switch
6. Brake Pedal Member Assembly
6-a. 16.7 - 25.5 N·m (1.7 - 2.6 kgf·m, 12.3 - 18.8 lb·ft)
6-b. 16.7 - 25.5 N·m (1.7 - 2.6 kgf·m, 12.3 - 18.8 lb·ft)
7. Pedal Stroke Sensor
7-a. 2.0 - 3.9 N·m (0.2 - 0.4 kgf·m, 1.4 - 2.9 lb·ft, 17.4 - 34.7 lb·in)

Brake Pedal Removal and Installation

Removal
Warning
•
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
•
When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
1.
Disconnect the battery negative ( - ) terminal and the service interlock connector.
(Refer to Battery Control System - "Auxiliary 12 V Battery - 2WD")
(Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
2.
Remove the crash pad lower panel.
(Refer to Body - "Crash Pad Panel" )
3.
Disconnect the stop lamp switch connector (A).

Brake System — Brake System / Brake Pedal / Removal and Installation / Removal illustration

4.
Disconnect the duct sensor connector (A).

Brake System — Brake System / Brake Pedal / Removal and Installation / Removal illustration

5.
Disconnect the shower duct connector (A).

Brake System — Brake System / Brake Pedal / Removal and Installation / Removal illustration

6.
Remove the shower duct (A) after removing the screw.

Brake System — Brake System / Brake Pedal / Removal and Installation / Removal illustration

7.
Remove the pedal support bracket after removing the nuts (A).

Tightening torque :
6.9 - 10.8 N·m (0.7 - 1.1 kgf·m, 5.1 - 8.0 lb·ft, 60.8 - 95.5 lb·in)

Brake System — Brake System / Brake Pedal / Removal and Installation / Removal illustration

8.
Remove the brake pedal arm mounting clevis pin (A) and split pin (B).

Brake System — Brake System / Brake Pedal / Removal and Installation / Removal illustration

Note
Do not reuse the split pin (B).
9.
Remove the Integrated Electronic Brake (IEB) assembly nuts (A).

Tightening torque :
16.7 - 25.5 N·m (1.7 - 2.6 kgf·m, 12.3 - 18.8 lb·ft)

Brake System — Brake System / Brake Pedal / Removal and Installation / Removal illustration

10.
Remove the front trunk.
(Refer to Body - "Front Trunk")
11.
Move IEB (A) in the direction of the arrow and make a workspace.

Brake System — Brake System / Brake Pedal / Removal and Installation / Removal illustration

12.
Remove the brake pedal assembly after removing the nut (A).

Tightening torque :
16.7 - 25.5 N·m (1.7 - 2.6 kgf·m, 12.3 - 18.8 lb·ft)

Brake System — Brake System / Brake Pedal / Removal and Installation / Removal illustration

Installation
Warning
•
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
•
When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
1.
Install in the reverse order of removal.
Note
•
Apply the grease when installing the brake pedal arm clevis pin (Grease type : GREASE PDLV-1)
•
Be careful not to change the mounting position of the clevis pin and split pin.
Information
To minimize damage to the thread and brake member assembly during installation, tighten all nuts with hands and then tighten them to the tightening torque values in the order shown below.

Brake System — Brake System / Brake Pedal / Removal and Installation / Installation illustration

2.
Check the brake pedal operating normally after installation.
3.
Perform the order below with the KDS.
(S/W Management → ABSESP - Braking Control → Brake Pedal Travel Sensor (PTS) Calibration)
Information
Refer to the KDS screen for operating conditions and details

Brake Pedal Disassembly and Reassembly

Disassembly
1.
Remove the brake pedal return spring (A).

Brake System — Brake System / Brake Pedal / Disassembly and Reassembly / Disassembly illustration

2.
Pull the locking plate (A) in the direction of the arrow.

Brake System — Brake System / Brake Pedal / Disassembly and Reassembly / Disassembly illustration

3.
Remove the stop lamp switch (A) by turning counterclockwise.

Brake System — Brake System / Brake Pedal / Disassembly and Reassembly / Disassembly illustration

Brake System — Brake System / Brake Pedal / Disassembly and Reassembly / Disassembly illustration

4.
Remove the brake pedal stroke sensor (A) after removing the bolts.

Tightening torque :
2.0 - 3.9 N·m (0.2 - 0.4 kgf·m, 1.4 - 2.9 lb·ft, 17.4 - 34.7 lb·in)

Brake System — Brake System / Brake Pedal / Disassembly and Reassembly / Disassembly illustration

Note
Handle the brake pedal stroke sensor (A) carefully as it is impact sensitive.
5.
Disassemble the brake pedal arm (A) after removing the bolt and nut.

Tightening torque :
24.5 - 34.3 N·m (2.5 - 3.5 kgf·m, 18.1 - 25.3 lb·ft)

Brake System — Brake System / Brake Pedal / Disassembly and Reassembly / Disassembly illustration

Reassembly
1.
Reassemble in the reverse order of disassembly.
Note
Apply the grease when installing the brake pedal arm clevis pin (Grease type : GREASE PDLV-1)
2.
Check the stop lamp switch clearance.
(Refer to Stop Lamp Switch - "Inspection")

Stop Lamp Switch Components and Components Location. Stop Lamp Switch Description and Operation

Stop Lamp Switch Components and Components Location

Component

Brake System — Brake System / Stop Lamp Switch / Components and Components Location / Component illustration

1. Brake Pedal Arm
1-a. 24.5 - 34.3 N·m (2.5 - 3.5 kgf·m, 18.1 - 25.3 lb·ft)
2. Brake Pedal Pad
3. Return Spring
4. Stopper

5. Stop Lamp Switch
6. Brake Pedal Member Assembly
6-a. 16.7 - 25.5 N·m (1.7 - 2.6 kgf·m, 12.3 - 18.8 lb·ft)
6-b. 16.7 - 25.5 N·m (1.7 - 2.6 kgf·m, 12.3 - 18.8 lb·ft)
7. Pedal Stroke Sensor
7-a. 2.0 - 3.9 N·m (0.2 - 0.4 kgf·m, 1.4 - 2.9 lb·ft, 17.4 - 34.7 lb·in)

Stop Lamp Switch Description and Operation

Description and Operation

Brake System — Brake System / Stop Lamp Switch / Description and Operation illustration

Operation principle of inductive non-contact switch
1.
Use the high frequency magnetic field and the induced current that are generated by oscillation (to approved voltage) of coil in switch.
2.
The eddy current is generated on surface of metal by self inductance effect if there is metal in high frequency magnetic field.
3.
The eddy current that is generated decreases the high frequency magnetic field as much as amount of generated by disturbing the switch's magnetic flux.
4.
ON-OFF by determining whether high voltage magnetic field decreases or not(calculate the voltage difference by length between metal and coil).

Stop Lamp Switch Circuit Diagram

Schematic Diagram

Brake System — Brake System / Stop Lamp Switch / Circuit Diagram / Schematic Diagram illustration

System Diagram

Brake System — Brake System / Stop Lamp Switch / Circuit Diagram / System Diagram illustration

Stop Lamp Switch Troubleshooting

Troubleshooting
1.
Part diagnosis
Name
Suspected Cause
Symptom
Correction
Switch fuse
Faulty fuse connection, Damaged fuse
–
DTC code : (Refer to "DTC guide")
–
Symptom : Starting failure, Cruise control function cancelation trouble, EPB function cancelation trouble, Stop lamp lighting trouble, ESC OFF light illuminated.
Brake System — Brake System / Stop Lamp Switch / Troubleshooting illustration A waveform inspection is performed using an oscilloscope on each part during vehicle acceleration/braking. (Refer to stop lamp switch circuit inspection procedures)

Brake System — Brake System / Stop Lamp Switch / Troubleshooting illustration Refer to the relevant repair procedures of the part when something abnormal is discovered in the waveform (Refer to the repair procedures of the relevant part and if necessary replace it)
Relay fuse
Faulty fuse connection, Damaged fuse
–
DTC code : (Refer to "DTC guide")
–
Symptom : Starting failure, Cruise control function cancelation trouble, EPB function cancelation trouble, Stop lamp lighting trouble, ESC OFF light illuminated.
Stop lamp switch
•
Damaged wiring of each part
•
Faulty connection to connector
•
Each part is defective
–
DTC code : (Refer to "DTC guide")
–
Symptom : Starting failure, Cruise control function cancelation trouble, EPB function cancelation trouble, Stop lamp lighting trouble , ESC OFF light illuminated.
Stop signal electronic module (If it applies)
–
DTC code : (Refer to "DTC guide")
–
Symptom : Starting failure, Cruise control function cancelation trouble, EPB function cancelation trouble, Stop lamp lighting trouble , ESC OFF light illuminated.
Vehicle Control Unit (VCU)
–
DTC code : (Refer to "DTC guide")
–
Symptom : Cruise control function cancelation trouble
Body Domain Control Unit (BDC)
–
Poor acceleration
Smart Key Unit (SMK)
–
Faulty engine start
Electronic Parking Brake (EPB)
–
Electronic Parking Brake (EPB)
Integrated Electronic Brake (IEB)
(Pressure sensor)
–
ESC OFF light illuminated.

2.
Symptom diagnosis
Symptom
Suspected causes
Correction
Faulty engine start
Switch fuse, Relay fuse, Stop lamp switch, Stop signal electronic module, IEB, Each wire, Connector
Brake System — Brake System / Stop Lamp Switch / Troubleshooting illustration Inspect waveform using an oscilloscope on each part during vehicle acceleration/braking. (Refer to stop lamp switch circuit inspection Procedures)

Brake System — Brake System / Stop Lamp Switch / Troubleshooting illustration Refer to the relevant repair procedures of the part when something abnormal is discovered in the waveform (Refer to the repair procedures of the relevant part and if necessary replace it)
ESC OFF light illuminated
Switch fuse, Relay fuse, Stop lamp switch, Stop signal electronic module, IEB, Each wire, Connector
P0504
Switch fuse, Relay fuse, Stop lamp switch, Stop signal electronic module, VCU, Each wire, Connector
Stop lamp does not working
Switch fuse, Relay fuse, Stop lamp switch, Stop signal electronic module, ECM, Each wire, Connector
Stop lamp always turns on
Stop lamp switch, Stop signal electronic module, Wiring short circuit, Damaged fuse

3.
Refer to DTC guide when the related DTC codes are displayed.

Stop Lamp Switch Removal and Installation

Removal
Warning
•
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
•
When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
1.
Disconnect the battery negative ( - ) terminal and the service interlock connector.
(Refer to Battery Control System - "Auxiliary 12 V Battery - 2WD")
(Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
2.
Remove the crash pad lower panel.
(Refer to Body - "Crash Pad Panel")
3.
Disconnect the stop lamp switch connector (A).

Brake System — Brake System / Stop Lamp Switch / Removal and Installation / Removal illustration

4.
Pull the locking plate (A) in the direction of the arrow.

Brake System — Brake System / Stop Lamp Switch / Removal and Installation / Removal illustration

5.
Turn the stop lamp switch (A) counterclockwise about 45 degrees and remove it.

Brake System — Brake System / Stop Lamp Switch / Removal and Installation / Removal illustration

Brake System — Brake System / Stop Lamp Switch / Removal and Installation / Removal illustration

Installation
Warning
•
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
•
When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
1.
Install in the reverse order of removal.
2.
Check the stop lamp switch clearance.
(Refer to Stop Lamp Switch - "Inspection")

Stop Lamp Switch Inspection. Front Brake Caliper Components and Components Location

Stop Lamp Switch Inspection

Clearance inspection
1.
Check the stop lamp switch clearance (A).

Stop lamp switch clearance (A) : 1.0 - 2.0 mm (0.04 - 0.08 in.)

Brake System — Brake System / Stop Lamp Switch / Inspection / Clearance inspection illustration

2.
If the clearance exceeds the standard, remove the stop lamp switch and check for damage to surrounding parts such as mounting clips.
(Refer to Brake System - "Stop Lamp Switch")
3.
If there is no damage, install the stop lamp switch and recheck the clearance.

Front Brake Caliper Components and Components Location

Component

Brake System — Brake System / Front Brake Caliper / Components and Components Location / Component illustration

1. Brake Pad Liner
2. Brake Pad
3. Torque Member
3-a. 98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)
4. Air Bleeder Screw Cap
4-a. 6.9 - 12.7 N·m (0.7 - 1.3 kgf·m, 5.1 - 9.4 lb·ft, 60.8 - 112.8 lb·in)
5. Caliper Body
5-a. 21.6 - 31.4 N·m (2.2 - 3.2 kgf·m, 15.9 - 23.1 lb·ft)

Front Brake Caliper Removal and Installation

Special Service Tool
Tool Name / Number
Illustration
Description
Piston expander
09581 - 11000

Brake System — Brake System / Front Brake Caliper / Removal and Installation / Special Service Tool illustration

Spreading the front brake caliper piston.

Removal
1.
Remove the front wheel and tires.
(Refer to Suspension System - "Wheel")
2.
Disconnect the front brake hose (A) after removing the bolt.

Tightening torque :
24.5 - 29.4 N·m (2.5 - 3.0 kgf·m, 18.1 - 21.7 lb·ft)

Brake System — Brake System / Front Brake Caliper / Removal and Installation / Removal illustration

Note
Do not reuse the washer (B) when installing the brake hose.
3.
Open the front brake caliper body (A) upwards after removing the bolt.

Tightening torque :
21.6 - 31.4 N·m (2.2 - 3.2 kgf·m, 15.9 - 23.1 lb·ft)

Brake System — Brake System / Front Brake Caliper / Removal and Installation / Removal illustration

4.
Remove the brake pads (A).

Brake System — Brake System / Front Brake Caliper / Removal and Installation / Removal illustration

5.
Remove the brake pad slider shims (A).

Brake System — Brake System / Front Brake Caliper / Removal and Installation / Removal illustration

6.
Remove the front caliper assembly (A) after removing the bolts and washers.

Tightening torque :
98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)

Brake System — Brake System / Front Brake Caliper / Removal and Installation / Removal illustration

Note
Do not reuse the torque member mounting bolt.
Installation
1.
Install in the reverse order of removal.
Note
•
Be careful not to damage the piston when pressing it.
•
Be careful not to touch the piston when installing the caliper body to the torque member.
•
Press the brake piston using SST (09581 - 11000) when installing the caliper body.

Brake System — Brake System / Front Brake Caliper / Removal and Installation / Installation illustration

2.
Fill the brake reservoir with brake fluid and perform air bleeding.
(Refer to Brake System - "Brake Bleeding")
3.
Check the brake fluid leakage and pedal operating condition.
4.
Depress the brake pedal several times to ensure that the brake pads are correctly positioned, then check operation.

Front Brake Disc Components and Components Location

Component

Brake System — Brake System / Front Brake Disc / Components and Components Location / Component illustration

1. Front Brake Caliper
1-a. 98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)
2. Front Brake Disc
2-a. 4.9 - 5.9 N·m (0.5 - 0.6 kgf·m, 3.6 - 4.3 lb·ft, 43.4 - 52.1 lb·in)
3. Front Axle Assembly

Front Brake Disc On Vehicle inspection

On Vehicle Inspection
Disc cleaning before inspection
The rust generated on brake discs of long-term non-operating vehicles is naturally removed under normal driving conditions. However, it can affect the thickness and runout measurements, so for accurate measurements, remove them according to the procedure below.
1.
Check the brake disc for rust.
2.
Spray with cleaning solution on rusted disc surface.

Cleaning Solution :
Water-Detergent [Water : 0.08 gal (300 ml) Detergent : 0.004 gal (15 ml)]

Warning
Do not use lubricating, oil-based cleaning agents (wax, rust inhibitors). Poor braking performance and risk of fire due to pad friction during braking may occur.
3.
Turn the vehicle ON, and then pull down the RH paddle shift (A) to enter the regenerative braking mode '0'.
Information
The rust of the brake disc can not be removed when in regenerative braking mode 1 or more.
4.
Drive the vehicle up to 30 mph (48 km/h) and depress the brake up to stop for complete repeat more than 5 cycles.
5.
Clean the brake disc with clean water.
6.
Check the brake disc for rust.
7.
If rust is not removed, repeat the above procedure again.
Front brake disc thickness check
1.
Remove the front wheel and tires.
(Refer to Suspension System - "Wheel")
2.
Check the brake disc for damage.
3.
Measure the brake disc thickness (A) and run-out using the micro meter and dial gauge at least 24 locations on the same column along the lines shown in the figure below.

Front brake disc thickness (A)
Disc standard : 30 mm (1.18 in.)
Disc service limit : 28 mm (1.10 in.)
The difference between each measured thickness
less than 0.015 mm (Column and Radial direction)

Brake System — Brake System / Front Brake Disc / On Vehicle inspection / On Vehicle Inspection illustration

4.
If the thickness difference between each measuring part is greater than standard, resurface or replace the brake disc.
Note
•
Resurface the brake disc according to the procedure based on the available machining equipment.
•
If the brake disc is less than or equal to the limit, replace the brake disc with a new one.
5.
Install the front wheel and tires.
(Refer to Suspension System - "Wheel")
Front Brake Disc Runout Inspection
1.
Remove the front wheel and tires.
(Refer to Suspension System - "Wheel")
2.
Install the dial gauge perpendicular to the brake disc's external diameter of 10 mm (0.40 in.) and rotate the disc to measure the run-out.

Brake Disc Runout :
Service limit : less than 0.050 mm (0.0019 in.)

Brake System — Brake System / Front Brake Disc / On Vehicle inspection / On Vehicle Inspection illustration

3.
If the brake disc run-out exceeds the limit, resurface or replace the brake disc.
Note
•
Resurface the brake disc according to the procedure based on the available machining equipment.
•
If the brake disc is less than or equal to the limit, replace the brake disc with a new one.
4.
Install the front wheel and tires.
(Refer to Suspension System - "Wheel")

Front Brake Disc Removal and Installation

Special Service Tool
Tool Name / Number
Illustration
Description
Piston Expander
09581 - 11000

Brake System — Brake System / Front Brake Disc / Removal and Installation / Special Service Tool illustration

Spreading the front brake caliper piston.

Removal
1.
Remove the front wheel and tires.
(Refer to Suspension System - "Wheel")
2.
Open the front brake caliper body (A) upwards after removing the bolt.

Tightening torque :
21.6 - 31.4 N·m (2.2 - 3.2 kgf·m, 15.9 - 23.1 lb·ft)

Brake System — Brake System / Front Brake Disc / Removal and Installation / Removal illustration

3.
Remove the brake pads (A).

Brake System — Brake System / Front Brake Disc / Removal and Installation / Removal illustration

4.
Remove the brake pad slider shims (A).

Brake System — Brake System / Front Brake Disc / Removal and Installation / Removal illustration

5.
Remove the front brake caliper (A) after removing the bolt and washer.

Tightening torque :
98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)

Brake System — Brake System / Front Brake Disc / Removal and Installation / Removal illustration

Note
•
Secrue the removed brake caliper (A) using a wire such as cable tie.

Brake System — Brake System / Front Brake Disc / Removal and Installation / Removal illustration

•
Do not reuse the front brake caliper mounting bolts.
6.
Remove the brake disc (A) after removing the screws.

Tightening torque :
4.9 - 5.9 N·m (0.5 - 0.6 kgf·m, 3.6 - 4.3 lb·ft, 43.4 - 52.1 lb·in)

Brake System — Brake System / Front Brake Disc / Removal and Installation / Removal illustration

Note
Be careful not to damage the hub bolts (A) when removing or installing the brake disc.

Brake System — Brake System / Front Brake Disc / Removal and Installation / Removal illustration

Information
If the brake disc screw is fixed, place the driver (A) and hit it with a hammer (B).

Brake System — Brake System / Front Brake Disc / Removal and Installation / Removal illustration

Installation
1.
Install in the reverse order of removal.
Note
•
Be careful not to damage the piston when pressing it.
•
Be careful not to touch the piston when installing the caliper body to the torque member.
•
Press the brake piston using SST (09581 - 11000) when installing the caliper body.

Brake System — Brake System / Front Brake Disc / Removal and Installation / Installation illustration

2.
Depress the brake pedal several times to ensure that the brake pads are correctly positioned, then check operation.

Rear Brake Caliper Components and Components Location

Component

Brake System — Brake System / Rear Brake Caliper / Components and Components Location / Component illustration

1. Brake Pad
2. Brake Pad Liner
3. Torque Member
3-a. 78.5 - 98.1 N·m (8.0 - 10.0 kgf·m, 57.9 - 72.3 lb·ft)

4. Air Bleeder Screw Cap
4-a. 13.7 - 19.6 N·m (1.4 - 2.0 kgf·m, 10.1 - 14.5 lb·ft)
5. Caliper Body
5-a. 21.6 - 31.4 N·m (2.2 - 3.2 kgf·m, 15.9 - 23.1 lb·ft)

Rear Brake Caliper Removal and Installation

Special Service Tool
Tool Name / Number
Illustration
Description
Rear Brake Piston Adjuster
09580 - 0U000

Brake System — Brake System / Rear Brake Caliper / Removal and Installation / Special Service Tool illustration

Used for compressing rear caliper piston

Removal
Warning
•
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
•
When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
1.
Perform the order below with the KDS.
(S/W Management → ABSESP - Braking Control → Brake Pad Change Mode)
Information
Refer to the KDS screen for operating conditions and details
2.
Disconnect the battery negative ( - ) terminal and the service interlock connector.
(Refer to Battery Control System - "Auxiliary 12 V Battery - 2WD")
(Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
3.
Remove the rear wheel and tires.
(Refer to Suspension System - "Wheel")
4.
Disconnect the Electronic Parking Brake (EPB) actuator connector (A).

Brake System — Brake System / Rear Brake Caliper / Removal and Installation / Removal illustration

5.
Separate the brake hose (A) after removing the bolt.

Tightening torque :
24.5 - 29.4 N·m (2.5 - 3.0 kgf·m, 18.1 - 21.7 lb·ft)

Brake System — Brake System / Rear Brake Caliper / Removal and Installation / Removal illustration

Note
Do not reuse the washer (B) when installing the brake hose.
6.
Open the rear brake caliper body (A) upwards after removing the bolt.

Tightening torque :
21.6 - 31.4 N·m (2.2 - 3.2 kgf·m, 15.9 - 23.1 lb·ft)

Brake System — Brake System / Rear Brake Caliper / Removal and Installation / Removal illustration

7.
Remove the brake pads (A).

Brake System — Brake System / Rear Brake Caliper / Removal and Installation / Removal illustration

8.
Remove the brake pad slider shims (A).

Brake System — Brake System / Rear Brake Caliper / Removal and Installation / Removal illustration

9.
Remove the rear torque member (A) after removing the bolts and washers.

Tightening torque :
78.5 - 98.1 N·m (8.0 - 10.0 kgf·m, 57.9 - 72.3 lb·ft)

Brake System — Brake System / Rear Brake Caliper / Removal and Installation / Removal illustration

Note
Do not reuse the torque member mounting bolt.
Installation
Warning
•
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
•
When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
1.
Install in the reverse order of removal.
Note
•
Be careful not to interfere with the torque member when assembling the caliper body.
•
Turn the brake piston clockwise using SST (09580 - 0U000) to press the brake piston when installing the brake caliper body to torque member.

Brake System — Brake System / Rear Brake Caliper / Removal and Installation / Installation illustration

•
Before installing the caliper body, check the position of the piston groove. If the location is fault, press it with the SST.
[Normal]

Brake System — Brake System / Rear Brake Caliper / Removal and Installation / Installation illustration

[Fault]

Brake System — Brake System / Rear Brake Caliper / Removal and Installation / Installation illustration

2.
Fill the brake reservoir with brake fluid and perform air bleeding.
(Refer to Brake System - "Brake Bleeding")
3.
Perform the order below with the KDS.
(S/W Management → ABSESP - Braking Control → Brake Pad Change Mode)
Information
Refer to the KDS screen for operating conditions and details
4.
Depress the brake pedal several times to ensure that the brake pads are correctly positioned, then check operation.
5.
Check the brake fluid leakage and pedal operating condition.
6.
Check if the parking brake is operating normally.

Rear Brake Disc Components and Components Location

Component

Brake System — Brake System / Rear Brake Disc / Components and Components Location / Component illustration

1. Rear Brake Caliper
1-a. 78.5 - 98.1 N·m (8.0 - 10.0 kgf·m, 57.9 - 72.3 lb·ft)
2. Rear Brake Disc
2-a. 4.9 - 5.9 N·m (0.5 - 0.6 kgf·m, 3.6 - 4.3 lb·ft, 43.4 - 52.1 lb·in)
3. Integrated Drive Axle (IDA)

Rear Brake Disc On Vehicle inspection

On Vehicle Inspection
Disc cleaning before inspection
The rust generated on brake discs of long-term non-operating vehicles is naturally removed under normal driving conditions. However, it can affect the thickness and runout measurements, so for accurate measurements, remove them according to the procedure below.
1.
Check the brake disc for rust.
2.
Spray with cleaning solution on rusted disc surface.

Cleaning Solution :
Water-Detergent [Water : 0.08 gal (300 ml) Detergent : 0.004 gal (15 ml)]

Warning
Do not use lubricating, oil-based cleaning agents (wax, rust inhibitors). Poor braking performance and risk of fire due to pad friction during braking may occur.
3.
Turn the vehicle ON, and then pull down the RH paddle shift (A) to enter the regenerative braking mode '0'.
Information
The rust of the brake disc can not be removed when in regenerative braking mode 1 or more.
4.
Drive the vehicle up to 30 MPH and depress the brake up to stop for complete repeat more than 5 cycles.
5.
Clean the brake disc with clean water.
6.
Check the brake disc for rust.
7.
If rust is not removed, repeat the above procedure again.
Rear brake thickness check
1.
Remove the rear wheel and tires.
(Refer to Suspension System - "Wheel")
2.
Check the brake disc for damage.
3.
Measure the brake disc thickness (A) and run-out using the micro meter and dial gauge at least 24 locations on the same column along the lines shown in the figure below.

Rear Brack Disc Thickness (A)
Disc standard : 12 mm (0.47 in.)
Disc limit : 10 mm (0.40 in.)
The difference between each measured thickness
less than 0.015 mm (Column and Radial direction)

Brake System — Brake System / Rear Brake Disc / On Vehicle inspection / On Vehicle Inspection illustration

4.
If the thickness difference between each measuring part is greater than standard, resurface or replace the brake disc.
Note
•
Resurface the brake disc according to the procedure based on the available machining equipment.
•
If the brake disc is less than or equal to the limit, replace the brake disc with a new one.
5.
Install the rear wheel and tires.
(Refer to Suspension System - "Wheel")
Rear Brake Disc Runout Inspection
1.
Remove the rear wheel and tires.
(Refer to Suspension System - "Wheel")
2.
Install the dial gauge perpendicular to the brake disc's external diameter of 10 mm (0.40 in.) and rotate the disc to measure the run-out.

Brake Disc Runout
Service limit : 0.055 mm (0.002 in.) or less.

Brake System — Brake System / Rear Brake Disc / On Vehicle inspection / On Vehicle Inspection illustration

3.
If the brake disc run-out exceeds the limit, resurface or replace the brake disc.
Note
•
Resurface the brake disc according to the procedure based on the available machining equipment.
•
If the brake disc is less than or equal to the limit, replace the brake disc with a new one.
4.
Install the rear wheel and tires.
(Refer to Suspension System - "Wheel")

Rear Brake Disc Removal and Installation

Special Service Tool
Tool Name / Number
Illustration
Description
Rear Brake Piston Adjuster
09580 - 0U000

Brake System — Brake System / Rear Brake Disc / Removal and Installation / Special Service Tool illustration

Used for compressing rear caliper piston

Removal
Warning
•
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
•
When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
1.
Perform the order below with the KDS.
(S/W Management → ABSESP - Braking Control → Brake Pad Change Mode)
Information
Refer to the KDS screen for operating conditions and details
2.
Disconnect the battery negative ( - ) terminal and the service interlock connector.
(Refer to Battery Control System - "Auxiliary 12 V Battery - 2WD")
(Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
3.
Remove the rear wheel and tires.
(Refer to Suspension System - "Wheel")
4.
Disconnect the Electronic Parking Brake (EPB) actuator connector (A).

Brake System — Brake System / Rear Brake Disc / Removal and Installation / Removal illustration

5.
Open the brake caliper body (A) upwards after removing the bolt.

Tightening torque :
21.6 - 31.4 N·m (2.2 - 3.2 kgf·m, 15.9 - 23.1 lb·ft)

Brake System — Brake System / Rear Brake Disc / Removal and Installation / Removal illustration

6.
Remove the brake pads (A).

Brake System — Brake System / Rear Brake Disc / Removal and Installation / Removal illustration

7.
Remove the brake pad slider shims (A).

Brake System — Brake System / Rear Brake Disc / Removal and Installation / Removal illustration

8.
Remove the rear brake caliper (A) after removing the bolts and washers.

Tightening torque :
78.5 - 98.1 N·m (8.0 - 10.0 kgf·m, 57.9 - 72.3 lb·ft)

Brake System — Brake System / Rear Brake Disc / Removal and Installation / Removal illustration

Note
•
Secrue the removed brake caliper (A) using a wire such as cable tie.

Brake System — Brake System / Rear Brake Disc / Removal and Installation / Removal illustration

•
Do not reuse the front brake caliper mounting bolts.
9.
Remove the brake disc (A) after removing the screws.

Tightening torque :
4.9 - 5.9 N·m (0.5 - 0.6 kgf·m, 3.6 - 4.3 lb·ft, 43.4 - 52.1 lb·in)

Brake System — Brake System / Rear Brake Disc / Removal and Installation / Removal illustration

Note
Be careful not to damage the hub bolts (A) when removing or installing the brake disc.

Brake System — Brake System / Rear Brake Disc / Removal and Installation / Removal illustration

Information
If the brake disc screw is fixed, place the driver (A) and hit it with a hammer (B).

Brake System — Brake System / Rear Brake Disc / Removal and Installation / Removal illustration

Installation
Warning
•
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
•
When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
1.
Install in the reverse order of removal.
Note
•
Be careful not to interfere with the torque member when assembling the caliper body.
•
Turn the brake piston clockwise using SST (09580 - 0U000) to press the brake piston when installing the brake caliper body to torque member.

Brake System — Brake System / Rear Brake Disc / Removal and Installation / Installation illustration

•
Before installing the caliper body, check the position of the piston groove. If the location is fault, press it with the SST.
[Normal]

Brake System — Brake System / Rear Brake Disc / Removal and Installation / Installation illustration

[Fault]

Brake System — Brake System / Rear Brake Disc / Removal and Installation / Installation illustration

2.
Perform the order below with the KDS.
(S/W Management → ABSESP - Braking Control → Brake Pad Change Mode)
Information
Refer to the KDS screen for operating conditions and details
3.
Depress the brake pedal several times to ensure that the brake pads are correctly positioned, then check operation.
4.
Check if the parking brake is operating normally.

Brake Pad Replacement

Replacement
Front brake pad
1.
Remove the front wheel and tires.
(Refer to Suspension System - "Wheel")
2.
Open the front brake caliper body (A) upwards after removing the bolt.

Tightening torque :
21.6 - 31.4 N·m (2.2 - 3.2 kgf·m, 15.9 - 23.1 lb·ft)

Brake System — Brake System / Brake Pad / Replacement illustration

3.
Remove the brake pads (A).

Brake System — Brake System / Brake Pad / Replacement illustration

4.
Remove the brake pad slider shims (A).

Brake System — Brake System / Brake Pad / Replacement illustration

Note
•
When replacing the brake pad, replace all brake pad parts (pad, slider shim, pad inner shim) together.
•
Note the direction when replacing the pad slider shim and inner pad inner shim.
•
Make sure that the pad slider shim fits securely when replacing the pad slider shim.
•
If the pad slider shim is deformed or not properly installed, the poor brake performance / drag / noise can occur.
•
Be careful not to deform the return spring (A) of the pad slider shim(retraction part).

Brake System — Brake System / Brake Pad / Replacement illustration

Rear brake pad
1.
Perform the order below with the KDS.
(S/W Management → ABSESP - Braking Control → Brake Pad Change Mode)
Information
Refer to the KDS screen for operating conditions and details
2.
Disconnect the battery negative ( - ) terminal and the service interlock connector.
(Refer to Battery Control System - "Auxiliary 12 V Battery - 2WD")
(Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
3.
Remove the rear wheel and tires.
(Refer to Suspension System - "Wheel")
4.
Disconnect the Electronic Parking Brake (EPB) actuator connector (A).

Brake System — Brake System / Brake Pad / Replacement illustration

5.
Open the rear brake caliper body (A) upwards after removing the bolt.

Tightening torque :
21.6 - 31.4 N·m (2.2 - 3.2 kgf·m, 15.9 - 23.1 lb·ft)

Brake System — Brake System / Brake Pad / Replacement illustration

6.
Remove the brake pads (A).

Brake System — Brake System / Brake Pad / Replacement illustration

7.
Remove the brake pad slider shims (A).

Brake System — Brake System / Brake Pad / Replacement illustration

Note
•
When replacing the brake pad, replace all brake pad parts (pad, slider shim, pad inner shim) together.
•
Note the direction when replacing the pad slider shim and inner pad inner shim.
•
Make sure that the pad slider shim fits securely when replacing the pad slider shim.
•
If the pad slider shim is deformed or not properly installed, the poor brake performance / drag / noise can occur.
•
Be careful not to deform the return spring (A) of the pad slider shim(retraction part).

Brake System — Brake System / Brake Pad / Replacement illustration

Brake Pad Inspection

Inspection
Brake Pad Check
1.
Check brake pad thickness (A). If the thickness is thinner than the limit, replace the brake pads.

Front brake pad thickness
Standard : 11.0 mm (0.433 in.)
Service limit : 3.0 mm (0.118 in.)


Rear brake disc pad thickness
Standard : 10.0 mm (0.393 in.)
Service Limit : 2.0 mm (0.078 in.)

Brake System — Brake System / Brake Pad / Inspection illustration

2.
Check that grease is applied to sliding contact points and check the pad and backing metal for damage.

Brake Pad Installation

Special Service Tool
Tool Name / Number
Illustration
Description
Piston Expander
09581 - 11000

Brake System — Brake System / Brake Pad / Installation / Special Service Tool illustration

Spreading the front brake caliper piston.
Rear Brake Piston Adjuster
09580 - 0U000

Brake System — Brake System / Brake Pad / Installation / Special Service Tool illustration

Used for compressing rear caliper piston

Installation
Front brake pad
1.
Install in the reverse order of removal.
Note
•
Observe the following precautions when installing the inner brake pads, incorrect installation may cause noise or compromise brake performance.
- Make sure that the inner brake pad wear indicator (A) is facing up on the brake caliper.

Brake System — Brake System / Brake Pad / Installation illustration

- Make sure that the inner brake pad L (LH caliper) or R (RH caliper) marks are facing up on the brake caliper.
•
Be careful not to damage the piston when pressing it.
•
Be careful not to interfere with the torque member when assembling the caliper body.
•
Press the brake piston using SST (09581 - 11000) when installing the caliper body.

Brake System — Brake System / Brake Pad / Installation illustration

2.
Depress the brake pedal several times to ensure that the brake pads are correctly positioned, then check operation.
Rear brake pad
1.
Install in the reverse order of removal.
Note
•
Observe the following precautions when installing the inner brake pads, incorrect installation may cause noise or compromise brake performance.
- Make sure that the inner brake pad wear indicator (A) is facing up on the brake caliper.

Brake System — Brake System / Brake Pad / Installation illustration

- Make sure that the inner brake pad L (LH caliper) or R (RH caliper) marks are facing up on the brake caliper.
•
Be careful not to interfere with the torque member when assembling the caliper body.
•
Turn the brake piston clockwise using SST (09580 - 0U000) to press the brake piston when installing the brake caliper body to torque member.

Brake System — Brake System / Brake Pad / Installation illustration

•
Before installing the caliper body, check the position of the piston groove. If the location is fault, press it with the SST.
[Normal]

Brake System — Brake System / Brake Pad / Installation illustration

[Fault]

Brake System — Brake System / Brake Pad / Installation illustration

2.
Perform the order below with the KDS.
(S/W Management → ABSESP - Braking Control → Brake Pad Change Mode)
Information
Refer to the KDS screen for operating conditions and details
3.
Depress the brake pedal several times to ensure that the brake pads are correctly positioned, then check operation.
4.
Check if the parking brake is operating normally.

Other information:

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Navigation-based Smart Cruise Control limitations

Navigation-based Smart Cruise Control in the Kia EV6 may operate abnormally, pause unexpectedly, or provide delayed speed assistance under the following circumstances. Because this system depends on navigation data, GPS positioning, map accuracy, road recognition, and Smart Cruise Control operation, the driver must always monitor the road and remain ready to control speed manually.

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Precautions for accident vehicle

Precautions for accident vehicle Electric vehicle includes a high voltage battery, which can lead to serious accidents such as short circuits or electric shocks if touched incorrectly.

 
Copyright © 2026 Kia EV6 Manuals ⏱ 0.0273