Kia EV6: Brake System

Contents:

Single-Use Parts

Single-Use Parts
Non-reusable parts (Single-Use Parts)
Workshop manual provides “Components and Components Location� which can be used to identify “Non-reusable parts�. When repairing a vehicle, Non-reusable parts such as fasteners, gaskets, washers, clips and garnishes must be replaced. Kia Non-reusable parts are designed to be installed only once.
Before working on a vehicle, check “Components and Components Location� to find the non-reusable parts in a system.
※ Symbol of Non-reusable parts
Symbol
Meaning

Brake System — Single-Use Parts illustration

Do not reuse the part. Replace with a new one.

※ Example of “Components and Components Location�

Brake System — Single-Use Parts illustration

High Voltage System General Safety Information and Caution ➤

High Voltage Shut-off Procedures

High Voltage Shut-off Procedures

High Voltage Shut-off Procedures
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Information
High Voltage Component : Battery System Assembly (BSA), motor assembly, inverter assembly, high voltage junction box, power cable, etc.
1.
Check the Battery Management Unit (BMU) weld flag with the KDS.
(Data Analysis → Battery Management System (BMS) → BMU Weld Flag)

Specified value : NO

Information
Refer to the KDS screen for operating conditions and details.
2.
Open the front trunk (A).

Brake System — High Voltage Shut-off Procedures illustration

3.
Open the low voltage (12 V) battery service cover (A).

Brake System — High Voltage Shut-off Procedures illustration

4.
Turn the POWER OFF, separate the low voltage (12 V) battery ( - ) terminal (A).

Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)

Brake System — High Voltage Shut-off Procedures illustration

5.
Disconnect the service interlock connector (A).

Brake System — High Voltage Shut-off Procedures illustration

Warning
•
Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
•
When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
Note
The service interlock connector cannot be completely removed.

Brake System — High Voltage Shut-off Procedures illustration

6.
Remove the front under cover.
(Refer to Motor and Reduction Gear System - "Front Under Cover")
7.
Remove the high voltage battery cover (A).

Tightening torque :
7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)

Brake System — High Voltage Shut-off Procedures illustration

8.
Disconnect the front high voltage junction box power cable (A).

Brake System — High Voltage Shut-off Procedures illustration

Note
How to disconnect the connector
1)
Release the locking clip (A) by pulling it.
2)
Disconnect the connector by pushing the lever (A) in the direction of the arrow while pressing the locking clip (B).

Brake System — High Voltage Shut-off Procedures illustration

9.
Remove the center floor rear under cover.
(Refer to Motor and Reduction Gear System - "Rear Under Cover")
10.
Disconnect the Integrated Charge Control Unit (ICCU) connector (A).

Brake System — High Voltage Shut-off Procedures illustration

Note
How to disconnect the connector
1)
Release the locking clip (A) by pulling it.
2)
Disconnect the connector while pressing the locking clip (B).

Brake System — High Voltage Shut-off Procedures illustration

11.
Disconnect the rear high voltage junction box power cable (A).

Brake System — High Voltage Shut-off Procedures illustration

Note
How to disconnect the connector
1)
Release the locking clip (A) by pulling it.
2)
Disconnect the connector by pushing the lever (A) in the direction of the arrow while pressing the locking clip (B).

Brake System — High Voltage Shut-off Procedures illustration

12.
Measure the voltage between the high voltage power connector and high voltage battery terminal to check whether the high voltage is shut-off.

30 V or less : Normal cut off high voltage circuit
Above 30 V : Fault on high voltage circuit

(1)
Measure the voltage between the high voltage power connector positive ( + ) terminal and negative ( - ) terminal.

Brake System — High Voltage Shut-off Procedures illustration

(2)
Measure the voltage between the high voltage battery positive ( + ) and negative ( - ) terminal.

Brake System — High Voltage Shut-off Procedures illustration

(3)
Measure the voltage between the high voltage battery positive ( + ) terminal and ground.

Brake System — High Voltage Shut-off Procedures illustration

(4)
Measure the voltage between the high voltage battery negative ( - ) terminal and ground.

Brake System — High Voltage Shut-off Procedures illustration

(5)
Measure the voltage between the rear high voltage battery positive ( + ) and negative ( - ) terminal.

Brake System — High Voltage Shut-off Procedures illustration

(6)
Measure the voltage between the rear high voltage battery positive ( + ) terminal and ground.

Brake System — High Voltage Shut-off Procedures illustration

(7)
Measure the voltage between the rear high voltage battery negative ( - ) terminal and ground.

Brake System — High Voltage Shut-off Procedures illustration

Warning
1)
Check for insulation breakdown via KDS and physical leakage current before working on EV.
2)
Remove the main fuse if insulation breakdown or leakage current is suspected. (Remove the main fuse even when DTC CODE ON such as PRA malfunction)
(Refer to High Voltage Battery Control System - "Main Fuse")
※ If there is no insulation breakdown or leakage current and it is normal, work without removing the main fuse.

Specification ➤

Special Service Tool

Special Service Tool
Tool Name / Number
Illustration
Description
Piston expander
09581 - 11000

Brake System — Special Service Tool illustration

Spreading the front brake caliper piston.
Rear brake piston adjuster
09580 - 0U000

Brake System — Special Service Tool illustration

Used for compressing rear caliper piston
Sensor cap remover
0K583 - R0400

Brake System — Special Service Tool illustration

Used for removal of wheel sensor cap
Sensor cap installer
09527 - AL500

Brake System — Special Service Tool illustration

Used for installing of wheel sensor cap (O.D : Φ86.6)
(Used with 09231 - 93100)
Handle
09231 - 93100

Brake System — Special Service Tool illustration

Handle
(Used with 09527 - AL500)
Air bleeding tool
0K580 - 3D100

Brake System — Special Service Tool illustration

Used for brake bleeding (regulating pressure)
(Used with 0K585 - E8100)
Air bleeding tool adaptor
0K585 - E8100

Brake System — Special Service Tool illustration

Used for brake bleeding (reservoir cap adapter)
(Used with 0K580 - 3D100)

Troubleshooting

Troubleshooting
1.
The brake system can be diagnosed quickly using the KDS (Refer to "DTC Diagnostic Guide").
(1)
Self diagnosis : Checking failure and code number (DTC)
(2)
Sensor data : Checking the system input/output data state
(3)
Forced operation : Checking the system operation condition
(4)
Additional function : Controlling other features including system option setting and zero point adjustment
The table below shows the most common defects and repair remedies in the brake system. Each number indicates the priority of the likely cause of the defects.
Brake warning lamp illuminates
Suspected Cause
Correction
1. Brake fluid level sensor (not connected securely)
Reconnect or replace
2. Low brake fluid level
Fill and leak check
3. Parking brake (Set)
Release
4. Integrated Electronic Brake (IEB)
Diagnosis Trouble Code (DTC) Inspection

Lower pedal or spongy pedal
Suspected Cause
Correction
1. Brake system (fluid leakage)
Repair
2. Brake system (air inflow)
Perform air bleeding procedure
3. Piston seal (Wear or damage)
Replacement
4. Integrated Electronic Brake (IEB)
Diagnosis Trouble Code (DTC) Inspection

Brake drag
Suspected Cause
Correction
1. Brake pedal free separation (minimum)
Adjustment
2. Pad (Crack or bent)
Replacement
3. Piston (stuck)
Replacement
4. Piston (frozen)
Replacement
5. Anchor or return spring (malfunction)
Replacement
6. Integrated Electronic Brake (IEB)
Diagnosis Trouble Code (DTC) Inspection

Uneven brake
Suspected Cause
Correction
1. Piston (stuck)
Replacement
2. Pad (Polluted)
Replacement
3. Piston (frozen)
Replacement
4. Disc (scratches)
Replacement
5. Pad (Crack or bent)
Replacement

Heavy pedal and brake trouble
Suspected Cause
Correction
1. Brake system (oil leakage)
Repair
2. Brake system (air inflow)
Perform air bleeding procedure
3. Pad (wear)
Replacement
4. Pad (Crack or bent)
Replacement
5. Pad (Polluted)
Replacement
6. Pad (Slippery)
Replacement
7. Disc (Dent or scratch)
Replacement
8. Integrated Electronic Brake (IEB)
Diagnosis Trouble Code (DTC) Inspection

Brake Noise
Suspected Cause
Correction
1. Pad (Crack or bent)
Replacement
2. Mounting bolt (Loose)
Retighten
3. Disc (Dent or scratch)
Replacement
4. Sliding pin (Wear)
Replacement
5. Pad (Polluted)
Cleaning
6. Pad (Slippery)
Replacement
7. Anchor or Return spring (Faulty)
Replacement
8. Brake pad shim (Damaged)
Replacement

Poor Braking Performance (at High Speed)
Suspected Cause
Correction
1. Pad (Wear)
Replacement
2. Integrated Electronic Brake (IEB)
Diagnosis Trouble Code (DTC) Inspection

Abnormal vibration when braking.
Suspected Cause
Correction
1. Excessive free play of the brake pedal
Adjustment
2. Integrated Electronic Brake (IEB)
Diagnosis Trouble Code (DTC) Inspection
3. Brake caliper
Replacement
4. Master cylinder cap seal
Replacement
5. Damaged brake line
Replacement
6. Disc juddering
Perform brake judder inspection and resurface or replace the disc

Brake bleeding ➤

Brake System ➤

Parking Brake System ➤

Integrated Electronic Brake (IEB) System ➤

ESC (Electronic Stability Control) System ➤

Other information:

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Precautions for accident vehicle

Precautions for accident vehicle Electric vehicle includes a high voltage battery, which can lead to serious accidents such as short circuits or electric shocks if touched incorrectly.

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: A Guide to Storage, Transport and Disposal of Old Battery Systems

Used high voltage battery system storage, transportation, disposal guide • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training.

Contents

Categories

 
Copyright © 2026 Kia EV6 Manuals � 0.0234