Kia EV6: Battery Control System (Long Range) / Electric Power Conversion System

Contents:

Components and Components Location

Component

Battery Control System (Long Range) — Electric Power Conversion System / Components and Components Location / Component illustration

1. Integrated Charging Control Unit (ICCU)
2. Multi Inverter Assembly
3. Inverter Assembly

Description and Operation

Description
Definition
•
The electric power conversion system is a system that converts power (AC/DC ↔ DC/AC) according to the usage requirements, using power generated externally or within a vehicle.
•
It converts the power from the vehicle's battery into power for driving the motor. The main components of a electric power conversion system include inverters and converters.
•
It converts more than one of the voltage, current frequency or phrase without loss of power.
Composition

Battery Control System (Long Range) — Electric Power Conversion System / Description and Operation / Description illustration

Inverter
•
It is a device that converts the DC power from the high-voltage battery in the vehicle into AC power for driving the motor.
•
Power conversion within the inverter is achieved by the MOSFET power modules, which switch according to control signals. Single-phase power is converted into 3-phase power, supplies the drive motor to enable rotation.
•
In addition to electric vehicles, hybrid vehicles also utilize power conversion to operate in electric drive mode. In this case, the reverse conversion process supplies voltage to the drive motor (reverse conversion device: a power device that converts the DC power from the high-voltage battery into AC power for use by the drive motor).
•
The inverter performs all the functions of both forward and reverse conversion devices.
[Inverter power conversion flow chart]

Battery Control System (Long Range) — Electric Power Conversion System / Description and Operation / Description illustration

Converter
AC/DC Converter
•
When the vehicle decelerates or brakes during operation, the drive motor acts as a generator, producing power. The generated power is then converted back into electrical energy for charge the high-voltage battery.
•
The AC/DC converter is also used when charging the vehicle besides during driving. During external slow charging, the On-Board Charger (OBC) within the Integrated Charging Control Unit (ICCU) converts the AC to DC, charging the high-voltage battery with the converted voltage.
DC/DC converter within the Low Voltage DC/DC Converter (LDC)
•
The Low Voltage DC/DC Converter (LDC) converts the voltage to low voltage to charge the low voltage (12 V) battery. The DC/DC converter within the LDC steps down the power supplied from the high-voltage battery to 12 V, providing power to the vehicle's auxiliary systems.
•
The LDC is comprised of a switching part, a transformer part. for power conversion, and a rectifier part. In the switching part, power is converted, and then in the transformer part, the voltage is stepped down. After that in the rectifier part, the voltage is rectified, and 12 V is output to the battery.
Information
Switching action: It is a device that converts power input from DC or AC into the desired output power through switching action.
DC/DC converter within the On-Board Charger (OBC)
•
The On-Board Charger (OBC) consists of an AC/DC converter and a DC/DC converter. The AC/DC converter comprises an EMI filter and a PFC converter.
Information
•
EMI Filter : It is a filter designed to remove high-frequency noise caused by input voltage.
•
PFC Converter : It is a converter used to compensate for power factor when converting AC voltage to DC.
•
During battery charging, the DC/DC converter within the On-Board Charger (OBC) is converted to DC by the AC/DC converter, and the output voltage of the high-voltage battery is controlled through the DC/DC converter within the OBC.
•
When the V2L connector is attached to the charging port or when AC 220V is used through the indoor V2L connector, the AC/DC converter and DC/DC converter inside the OBC perform bidirectional power conversion.

Battery Control System (Long Range) — Electric Power Conversion System / Description and Operation / Description illustration

Battery (12 V) Specification

Specification
Item
Specification
Type
eAGM60L-DIN
Capacity [20HR/5HR] (AH)
60 / 48
Cold cranking amperage (A)
500
Reserve capacity (Min)
100
Specific gravity
1.30 - 1.32 [25°C (77°F)]
Voltage (V)
12

Information
Battery Size
Type
Width
Length
Height
Total Height
mm (in.)
eAGM60L-DIN
239 - 243 (9.40 - 9.56)
173 - 175 (6.81 - 6.89)
164.5 - 167.5 (6.48 - 6.60)
187 - 190 (7.36 - 7.48)

Battery Control System (Long Range) — Electric Power Conversion System / Battery (12 V) / Specification illustration

Battery (12 V) Components and Components Location

Component

Battery Control System (Long Range) — Electric Power Conversion System / Battery (12 V) / Components and Components Location / Component illustration

1. Low Voltage (12 V) Battery Negative ( - ) Cable
1-a. 7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)
2. Low Voltage (12 V) Battery Positive ( + ) Cable
2-a. 7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)
3. Battery Clamp
3-a. 9.8 - 13.7 N·m (1.0 - 1.4 kgf·m, 7.2 - 10.1 lb·ft)
4. Low Voltage (12 V) Battery
5. Vehicle Control Unit (VCU)
5-a. 9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)
6. Battery Tray
6-a. 9.8 - 13.7 N·m (1.0 - 1.4 kgf·m, 7.2 - 10.1 lb·ft)

Battery (12 V) Description and Operation

Description
•
The low voltage (12 V) battery supplies power to electronic components excluding high voltage components.
•
The high voltage of a high voltage battery is converted into a low voltage (DC 12 V) through the LDC to charge the low voltage (12 V) battery.
Battery Label Information

Battery Control System (Long Range) — Electric Power Conversion System / Battery (12 V) / Description and Operation / Description illustration

1.
Battery specifications
–
AGM : Absorbent Glass Material
–
CMF : Closed Maintenance Free
–
MF : Maintenance Free
2.
Battery capacity (20 Ah)
3.
Terminal location
–
L : battery positive ( + ) terminal on the left.
–
R : battery positive ( + ) terminal on the right.
4.
Battery type
–
BCI (Battery Council International) : Intruding terminal
–
DIN (Deutsche Industric Normen) : Recessed terminal
5.
Cold Cranking Ampere (CCA)
Information
CCA : The amount of current that can be supplied for 30 seconds while maintaining a voltage of more than 7.2 V at -18°C (-0.4°F).
6.
Part number
7.
Reserve Capacity (RC)
Information
RC : The amount of time that can be supplied 25 A while maintaining the minimum voltage of 10.5 V at 26.7°C (80°F).

Battery (12 V) Removal and Installation - 2WD

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Low Voltage (12 V) Battery
1.
Open the front trunk (A).

Battery Control System (Long Range) — Electric Power Conversion System / Battery (12 V) / Removal and Installation - 2WD / Removal illustration

2.
Open the service cover (A).

Battery Control System (Long Range) — Electric Power Conversion System / Battery (12 V) / Removal and Installation - 2WD / Removal illustration

3.
Disconnect the low voltage (12 V) battery negative ( - ) terminal (A).

Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)

Battery Control System (Long Range) — Electric Power Conversion System / Battery (12 V) / Removal and Installation - 2WD / Removal illustration

4.
Disconnect the service interlock connector (A).

Battery Control System (Long Range) — Electric Power Conversion System / Battery (12 V) / Removal and Installation - 2WD / Removal illustration

Warning
Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
Note
The service interlock connector cannot be completely removed.

Battery Control System (Long Range) — Electric Power Conversion System / Battery (12 V) / Removal and Installation - 2WD / Removal illustration

5.
Open the low voltage (12 V) battery positive ( + ) terminal cover (A).

Battery Control System (Long Range) — Electric Power Conversion System / Battery (12 V) / Removal and Installation - 2WD / Removal illustration

6.
Disconnect the low voltage (12 V) battery positive ( + ) terminal (A).

Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)

Battery Control System (Long Range) — Electric Power Conversion System / Battery (12 V) / Removal and Installation - 2WD / Removal illustration

7.
Remove the low voltage (12 V) battery (A) after removing the clamp (B).

Tightening torque :
9.8 - 13.7 N·m (1.0 - 1.4 kgf·m, 7.2 - 10.1 lb·ft)

Battery Control System (Long Range) — Electric Power Conversion System / Battery (12 V) / Removal and Installation - 2WD / Removal illustration

Low Voltage (12 V) Battery Tray
1.
Remove the low voltage (12 V) battery.
(Refer to low voltage (12 V) Battery - "Removal and Installation - 2WD")
2.
Remove the Vehicle Control Unit (VCU).
(Refer to Motor & Reduction Gear System - "Vehicle Control Unit (VCU)")
3.
Separate the wiring (A) from the tray.

Battery Control System (Long Range) — Electric Power Conversion System / Battery (12 V) / Removal and Installation - 2WD / Removal illustration

4.
Remove the low voltage (12 V) battery tray (A).

Tightening torque :
9.8 - 13.7 N·m (1.0 - 1.4 kgf·m, 7.2 - 10.1 lb·ft)

Battery Control System (Long Range) — Electric Power Conversion System / Battery (12 V) / Removal and Installation - 2WD / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.
Note
•
Install the low voltage (12 V) battery and the tray to the specified torque.
•
If the low voltage (12 V) battery is dropped, it may cause internal damage. (Do not reuse)
•
When installing the low voltage (12 V) battery, install the clamp correctly.
•
When replacing the low voltage (12 V) battery, be sure to replace it with the same specification(capacity, manufacturer, etc.) as the battery installed originally. When the different specification is installed, it may be determined that the battery performance is abnormal by the battery sensor.

Battery (12 V) Removal and Installation - 4WD

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Low Voltage (12 V) Battery
1.
Open the front trunk (A).

Battery Control System (Long Range) — Electric Power Conversion System / Battery (12 V) / Removal and Installation - 4WD / Removal illustration

2.
Open the service cover (A).

Battery Control System (Long Range) — Electric Power Conversion System / Battery (12 V) / Removal and Installation - 4WD / Removal illustration

3.
Disconnect the low voltage (12 V) battery negative ( - ) terminal (A).

Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)

Battery Control System (Long Range) — Electric Power Conversion System / Battery (12 V) / Removal and Installation - 4WD / Removal illustration

4.
Disconnect the service interlock connector (A).

Battery Control System (Long Range) — Electric Power Conversion System / Battery (12 V) / Removal and Installation - 4WD / Removal illustration

Warning
Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
Note
The service interlock connector cannot be completely removed.

Battery Control System (Long Range) — Electric Power Conversion System / Battery (12 V) / Removal and Installation - 4WD / Removal illustration

5.
Open the low voltage (12 V) battery positive ( + ) terminal cover (A).

Battery Control System (Long Range) — Electric Power Conversion System / Battery (12 V) / Removal and Installation - 4WD / Removal illustration

6.
Disconnect the low voltage (12 V) battery positive ( + ) terminal (A).

Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)

Battery Control System (Long Range) — Electric Power Conversion System / Battery (12 V) / Removal and Installation - 4WD / Removal illustration

7.
Remove the low voltage (12 V) battery (A) after removing the clamp (B).

Tightening torque :
9.8 - 13.7 N·m (1.0 - 1.4 kgf·m, 7.2 - 10.1 lb·ft)

Battery Control System (Long Range) — Electric Power Conversion System / Battery (12 V) / Removal and Installation - 4WD / Removal illustration

Low Voltage (12 V) Battery Tray
1.
Remove the low voltage (12 V) battery.
(Refer to low voltage (12 V) Battery - "Removal and Installation - 4WD")
2.
Remove the Vehicle Control Unit (VCU).
(Refer to Motor & Reduction Gear System - "Vehicle Control Unit (VCU)")
3.
Separate the wiring (A, B) from the tray.

Battery Control System (Long Range) — Electric Power Conversion System / Battery (12 V) / Removal and Installation - 4WD / Removal illustration

4.
Remove the low voltage (12 V) battery tray (A).

Tightening torque :
9.8 - 13.7 N·m (1.0 - 1.4 kgf·m, 7.2 - 10.1 lb·ft)

Battery Control System (Long Range) — Electric Power Conversion System / Battery (12 V) / Removal and Installation - 4WD / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.
Note
•
Install the low voltage (12 V) battery and the tray to the specified torque.
•
If the low voltage (12 V) battery is dropped, it may cause internal damage. (Do not reuse)
•
When installing the low voltage (12 V) battery, install the clamp correctly.
•
When replacing the low voltage (12 V) battery, be sure to replace it with the same specification(capacity, manufacturer, etc.) as the battery installed originally. When the different specification is installed, it may be determined that the battery performance is abnormal by the battery sensor.

Battery Sensor Specification. Battery Sensor Components and Components Location

Battery Sensor Specification

Specification
Item
Specification
Rated voltage (V)
12 - 14
Operating voltage (V)
6 - 18
Operating temperature [°C (°F)]
-40 to 105 (-40 to 221)
Parasitic current (uA)
Maximum 300

Battery Sensor Components and Components Location

Component

Battery Control System (Long Range) — Electric Power Conversion System / Battery Sensor / Components and Components Location / Component illustration

1. Battery Sensor Connector
2. Battery Sensor
2-a. 7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)
2-b. 26.5 - 32.4 N·m (2.7 - 3.3 kgf·m, 19.5 - 23.9 lb·ft)





Battery Sensor Description and Operation

Description
•
The battery sensor is installed on the low voltage (12 V) battery negative ( - ) terminal and is also known as Intelligent Battery Sensor (IBS).

Battery Control System (Long Range) — Electric Power Conversion System / Battery Sensor / Description and Operation / Description illustration

•
The IBS continuously monitors the State of Charge (SOC) of the battery to maintain a consistent level of charge.
•
It manages the battery system to ensure the battery is used under optimal conditions, predicts the timing for battery replacement, and detects faulty batteries in advance.
•
It detects voltage changes supplied to the electrical actuator and monitors input and output currents of the low voltage (12 V) battery.
•
If the air conditioning function is used for more than 5 minutes while driving, after powering off, 30 minutes later, the SOC of the low voltage (12 V) battery is checked. If the battery voltage over the reference value, this serves as a reference signal to provide data to the DATC to activate the after-blow function.
•
It operates in the entire network (CAN) sleep state based on signals detected by IBS to perform vehicle power shutdown and prevent battery discharge by the power domain controller's internal current interruption system.
•
When the low voltage (12 V) battery discharges, the signal is used to transmit the battery voltage to the Vehicle Control Unit (VCU) through the power domain controller, and after determining the possibility of charging by the VCU, the Low Voltage DC/DC Converter (LDC) conversion device charges the low voltage (12 V) battery.

Battery Control System (Long Range) — Electric Power Conversion System / Battery Sensor / Description and Operation / Description illustration

Battery Sensor Removal and Installation - 2WD

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Disconnect the service interlock connector (A).

Battery Control System (Long Range) — Electric Power Conversion System / Battery Sensor / Removal and Installation - 2WD / Removal illustration

Warning
Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
Note
The service interlock connector cannot be completely removed.

Battery Control System (Long Range) — Electric Power Conversion System / Battery Sensor / Removal and Installation - 2WD / Removal illustration

2.
Remove the front trunk.
(Refer to Body - "Front Trunk")
3.
Disconnect the low voltage (12 V) battery negative ( - ) terminal (A).

Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)

Battery Control System (Long Range) — Electric Power Conversion System / Battery Sensor / Removal and Installation - 2WD / Removal illustration

4.
Disconnect the battery sensor connector (A).

Battery Control System (Long Range) — Electric Power Conversion System / Battery Sensor / Removal and Installation - 2WD / Removal illustration

5.
Remove the battery sensor (A) after removing the bolt.

Tightening torque :
26.5 - 32.4 N·m (2.7 - 3.3 kgf·m, 19.5 - 23.9 lb·ft)

Battery Control System (Long Range) — Electric Power Conversion System / Battery Sensor / Removal and Installation - 2WD / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.
Note
•
Install the battery sensor to the specified torque.
•
If the battery sensor is dropped, it may cause internal damage. (Do not reuse)

Battery Sensor Removal and Installation - 4WD

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Disconnect the service interlock connector (A).

Battery Control System (Long Range) — Electric Power Conversion System / Battery Sensor / Removal and Installation - 4WD / Removal illustration

Warning
Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
Note
The service interlock connector cannot be completely removed.

Battery Control System (Long Range) — Electric Power Conversion System / Battery Sensor / Removal and Installation - 4WD / Removal illustration

2.
Remove the front trunk.
(Refer to Body - "Front Trunk")
3.
Disconnect the low voltage (12 V) battery negative ( - ) terminal (A).

Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)

Battery Control System (Long Range) — Electric Power Conversion System / Battery Sensor / Removal and Installation - 4WD / Removal illustration

4.
Disconnect the battery sensor connector (A).

Battery Control System (Long Range) — Electric Power Conversion System / Battery Sensor / Removal and Installation - 4WD / Removal illustration

5.
Remove the battery sensor (A) after removing the bolt.

Tightening torque :
26.5 - 32.4 N·m (2.7 - 3.3 kgf·m, 19.5 - 23.9 lb·ft)

Battery Control System (Long Range) — Electric Power Conversion System / Battery Sensor / Removal and Installation - 4WD / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.
Note
•
Install the battery sensor to the specified torque.
•
If the battery sensor is dropped, it may cause internal damage. (Do not reuse)

Inverter Assembly (4WD) Specification. Inverter Assembly (4WD) Components and Components Location

Inverter Assembly (4WD) Specification

Specification
Item
Specification
Input voltage (V)
452.5 - 778.3
Operating voltage (V)
9 - 16
Continuous current (A)
75 (@20 min.)
Maximum ampere (A)
190 (@15 sec.)

Inverter Assembly (4WD) Components and Components Location

Component

Battery Control System (Long Range) — Electric Power Conversion System / Inverter Assembly (4WD) / Components and Components Location / Component illustration

1. High Voltage Junction Box Service Cover
1-a. 3.9 - 5.9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)
2. Front High Voltage Junction Box
2-a. 6.9 - 9.8 N·m (0.7 - 1.0 kgf·m, 5.1 - 7.2 lb·ft)
2-b. 6.9 - 9.8 N·m (0.7 - 1.0 kgf·m, 5.1 - 7.2 lb·ft)
3. Inverter Assembly
3-a. 3.9 - 5.9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)

Inverter Assembly (4WD) Description and Operation

Description
•
The inverter assembly is installed on the front-wheel drive motor and converts DC power to AC power (variable frequency, variable voltage).
•
It controls the rotational speed and torque of the motor through the power control.
•
In the Power Electric (PE) system based on the E-GMP platform, the drive motor installed on the front wheel is configured with an integrated inverter and reducer.
•
By the power modules within the inverter, we control to maximize both the rotation speed of the drive motor and the amount of regenerative braking charging into the high-voltage battery.

Battery Control System (Long Range) — Electric Power Conversion System / Inverter Assembly (4WD) / Description and Operation / Description illustration

Inverter Assembly (4WD) Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Drain the motor coolant.
(Refer to Cooling System - "Motor Coolant")
2.
Remove the front high voltage junction box.
(Refer to High Voltage Distributing System - "Front High Voltage Junction Box")
3.
Separate the inverter cooling quick connector hose (A).

Battery Control System (Long Range) — Electric Power Conversion System / Inverter Assembly (4WD) / Removal and Installation / Removal illustration

Battery Control System (Long Range) — Electric Power Conversion System / Inverter Assembly (4WD) / Removal and Installation / Removal illustration

4.
Remove the inverter assembly (A) after removing the bolts.

Tightening torque :
3.9 - 5.9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)

Battery Control System (Long Range) — Electric Power Conversion System / Inverter Assembly (4WD) / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.
Note
•
Install the inverter assembly to the specified torque.
•
If inverter assembly is dropped, it may cause internal damage. (Do not reuse)
•
Replace the gasket (A) and check the installation before installing the inverter assembly.

Battery Control System (Long Range) — Electric Power Conversion System / Inverter Assembly (4WD) / Removal and Installation / Installation illustration

2.
Perform the PE system leak test with the KDS.
(Refer to High Voltage Distributing System - "Front High Voltage Junction Box")
3.
Fill the motor coolant.
(Refer to Cooling System - "Coolant")
4.
Perform the Initialization of Automatic Resolver Offset Calibration procedures with the KDS.
(S/W Management → Front Motor Control Unit (MCU) → Initialization of Automatic Resolver Offset Calibration)
Information
Refer to the KDS screen for operating conditions and details.

Low Voltage DC/DC Converter (LDC) Description and Operation

Description
•
There are the high voltage and low voltage (12 V) battery to supply and store the power related with driving an EV. The low voltage (12 V) battery that is as to power device supplied to electric devices and control units in the vehicle is required to extra charging device.
•
If the battery state of charge (SOC) is detected by the battery sensor, it is input into the Vehicle Control Unit (VCU) through the power domain controller. The VCU judges the charging possibility and charges the low voltage (12 V) battery through the cooperative control Battery Management Unit (BMU) and Integrated Charge Control Unit (ICCU) by operating the IG3 relay when charging is necessary. In addition, the related control units are activated.
•
If the low voltage (12 V) battery's voltage does not exceed the reference, the Low DC/DC Converter (LDC) lowers the high voltage to the voltage for charging the low voltage (12 V) battery and charges it. (High voltage DC → Low voltage DC)
•
The low voltage (12 V) battery charging stops when it exceeds the reference value by operating the burst mode on LDC to improve battery efficiency.
•
It has to monitoring the SOC of the low voltage (12 V) battery to control the LDC through the battery sensor. If the SOC is less than the reference value, the charging starts and maximum 90%.
•
The LDC is integrated with the On-Board Charger (OBC) in the Integrated Charge Control Unit (ICCU).

Battery Control System (Long Range) — Electric Power Conversion System / Low Voltage DC/DC Converter (LDC) / Description and Operation / Description illustration

[The flowchart when charge the low voltage (12 V) battery by Low DC/DC Converter (LDC)]

Battery Control System (Long Range) — Electric Power Conversion System / Low Voltage DC/DC Converter (LDC) / Description and Operation / Description illustration

Information
When the low voltage (12 V) battery is not charged
•
When the lever is not P
•
When the trunk is open
•
When the SOC of a high voltage battery is less than 35%
•
When the battery sensor or electric devices has trouble

Low Voltage DC/DC Converter (LDC) Troubleshooting

Troubleshooting
How to remedy when the fault code occurs
Item
Major Fault Code
Suspected Cause
Inspection
Low Voltage DC/DC Converter (LDC) inspection
• Output overvoltage fault
• LDC
• Replace the Integrated Charge Control Unit (ICCU) when the same problem occurs after the vehicle restarts
• LDC voltage control fault
• Sensors fault
- Current sensor offset calibration abnormality
- Temperature sensor open circuit/short circuit/performance abnormality fault
- Input / Output voltage sensor fault
• PWM output fault
Vehicle inspection
• Output terminal path fault
• Wiring and connectors between the LDC output terminal and the high voltage junction box
• Check the LDC output circuit and cable connection condition
Coolant system fault
• Coolant system
• Low coolant
• Electric Water Pump (EWP)
• Inspect the EWP
• Input over current fault
• Low voltage (12 V) Battery discharged
• 12 V electric component overload
• Check the low voltage (12 V) battery discharge condition
• Check abnormal operation or short circuit conditions of 12 V electric components

Low Voltage DC/DC Converter (LDC) Replacement. Multi Inverter Assembly Specification

Low Voltage DC/DC Converter (LDC) Replacement

Replacement
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Note
The Low Voltage DC/DC Converter (LDC) cannot be replaced individually due to included in the Integrated Charging Control Unit (ICCU). If necessary, replace the ICCU.
1.
Replace the Integrated Charge Control Unit (ICCU).
(Refer to High Voltage Charging System - "Integrated Charger and Converter Unit (ICCU)")

Multi Inverter Assembly Specification

Specification
Item
Specification
Input voltage (V)
452.5 - 778.3
Operating voltage (V)
9 - 16
Continuous current (A)
180 (@20 min.)
Maximum ampere (A)
245 (@15 sec.)

Multi Inverter Assembly Components and Components Location

Component

Battery Control System (Long Range) — Electric Power Conversion System / Multi Inverter Assembly / Components and Components Location / Component illustration

1. High Voltage Junction Box Service Cover
1-a. 3.9 - 5.9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)
2. Rear High Voltage Junction Box
2-a. 6.9 - 9.8 N·m (0.7 - 1.0 kgf·m, 5.1 - 7.2 lb·ft)
2-b. 15.7 - 23.5 N·m (1.6 - 2.4 kgf·m, 11.6 - 17.4 lb·ft)
2-c. 19.6 - 23.5 N·m (1.8 - 2.7 kgf·m, 14.5 - 17.4 lb·ft)
3. Multi Inverter Assembly
3-a. 3.9 - 5.9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)

Multi Inverter Assembly Description and Operation

Description
•
The Power Electric (PE) system based on the E-GMP is composed of a motor, gearbox, inverter, and battery.

Battery Control System (Long Range) — Electric Power Conversion System / Multi Inverter Assembly / Description and Operation / Description illustration

•
Unlike conventional electric vehicles, electric cars based on the E-GMP platform connect the motor and inverter internally, reducing weight caused by cables and decrease volume through integration.
•
It improves the driving distance of electric vehicles and maximizes driving efficiency.
•
The multi inverter assembly is installed on the rear-wheel drive motor and converts DC power to AC power (variable frequency, variable voltage).
•
In the case of driving and boost control for charging, it increases the voltage applied to the drive motor to obtain the appropriate driving force for the driving situation.
•
Inside the multi inverter assembly, it is divided into Inverter 1 and 2. During driving and charging, it maintains optimal conditions for both states through different controls (high-efficiency mode and high-power mode) suitable for each situation.
Information
The driving mode is determined by the motor system's torque or speed and the battery's available charge, but it can be changed based on the driver's acceleration intent.
–
High-Efficiency Mode: In typical driving situations, Inverter 1 operates to drive the vehicle at low or moderate speeds.
–
High-Power Mode: Both Inverter 1 and 2 operate simultaneously to drive the vehicle in situations requiring high speed or high torque.

Battery Control System (Long Range) — Electric Power Conversion System / Multi Inverter Assembly / Description and Operation / Description illustration

•
By appropriately controlling inverters 1 and 2 during charging, the 800v high-voltage battery can be charged with the existing 400 V quick charger, improving efficiency in this case.
•
The 400 V boosts to 800 V when quick charge.
•
It is a next generation charging system for 400 V and 800 V multi-charging. In 400 V charging infrastructure, a motor and inverter are used to charge the 800 V battery and in the 800 V charging infrastructure, the battery is charged by the high voltage input from the charger.

Battery Control System (Long Range) — Electric Power Conversion System / Multi Inverter Assembly / Description and Operation / Description illustration

Multi Inverter Assembly Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Remove the rear high voltage junction box.
(Refer to High Voltage Distributing System - "Rear High Voltage Junction Box")
2.
Separate the multi inverter cooling quick connector hoses (A).

Battery Control System (Long Range) — Electric Power Conversion System / Multi Inverter Assembly / Removal and Installation / Removal illustration

3.
Disconnect the multi inverter assembly connector (A).

Battery Control System (Long Range) — Electric Power Conversion System / Multi Inverter Assembly / Removal and Installation / Removal illustration

4.
Separate the wiring protector (A) from multi inverter assembly.

Tightening torque :
6.9 - 9.8 N·m (0.7 - 1.0 kgf·m, 5.1 - 7.2 lb·ft)

Battery Control System (Long Range) — Electric Power Conversion System / Multi Inverter Assembly / Removal and Installation / Removal illustration

5.
Remove the ground cable (A) after removing the bolt from the motor.

Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)

Battery Control System (Long Range) — Electric Power Conversion System / Multi Inverter Assembly / Removal and Installation / Removal illustration

6.
Remove the multi inverter assembly cover (A) after removing the fasteners.

Battery Control System (Long Range) — Electric Power Conversion System / Multi Inverter Assembly / Removal and Installation / Removal illustration

7.
Remove the multi inverter assembly (A) after removing the bolts.

Tightening torque :
3.9 - 5.9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)

Battery Control System (Long Range) — Electric Power Conversion System / Multi Inverter Assembly / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.
Note
•
Install the multi inverter assembly to the specified torque.
•
If multi inverter assembly is dropped, it may cause internal damage. (Do not reuse)
•
Replace the gasket (A) and check the installation before installing the multi inverter assembly.

Battery Control System (Long Range) — Electric Power Conversion System / Multi Inverter Assembly / Removal and Installation / Installation illustration

•
Perform the PE system leak test procedure before installing the multi-inverter assembly in the vehicle.
2.
Perform the Initialization of Automatic Resolver Offset Calibration procedures with the KDS.
(S/W Management → Rear Motor Control Unit (MCU) → Initialization of Automatic Resolver Offset Calibration)
Information
Refer to the KDS screen for operating conditions and details.

Other information:

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Linking and unlinking profile

How to link user profile Open the infotainment settings menu and select Setup > User profile > Profile setting > Link Digital Key (Smartphone) to begin the Kia EV6 profile linking process. After selecting Link, the digital key associated with the registered smartphone number and its [Group] will connect to the chosen user profile.

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Rain Sensor Removal and Installation

Removal • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training.

Contents

Categories

 
Copyright © 2026 Kia EV6 Manuals ⏱ 0.0237