Contents:
| Removal |
|
| 1. |
Remove the floor console upper cover.
(Refer to Floor Console - "Floor Console Upper Cover")
|
| 2. |
Remove the console tray cover (A).
|
| 3. |
Remove the bolts (A).
[Console Mounting Bracket's Side]
[Console Rear Mounting Bracket's Side]
[Driver's Side]
[Passenger's Side]
|
| 4. |
Remove the floor console assembly (A).
|
| Installation |
|
| 1. |
Install in the reverse order of removal.
|
| Disassembly |
|
| 1. |
Remove the rear console upper garnish (A).
|
| 2. |
Remove the cover (A) after removing the screws.
|
| 1. |
Remove the rear console cover.
|
| 2. |
Remove the console armrest (A) after removing the screws.
|
| 1. |
Remove the console armrest.
|
| 2. |
Remove the floor console assembly.
(Refer to Floor Console - "Floor Console Assembly")
|
| 3. |
Remove the floor console storage box (A) after removing the screws.
|
| 4. |
Remove the floor console lower garnish (A) after removing the screws.
|
| 5. |
Remove the floor console wiring (A) after removing the fasteners.
|
| 6. |
Remove the tray (A) after removing the screws.
|
| Reassembly |
|
| 1. |
Reassemble in the reverse order of disassembly.
|
| Removal |
|
| 1. |
Remove the floor console switch.
(Refer to Floor Console - "Floor Console Upper Cover")
|
| Installation |
|
| 1. |
Install in the reverse order of removal.
|
| Removal |
| 1. |
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage
service interlock connector.
|
| 2. |
Remove the rear console upper garnish (A).
|
| 3. |
Remove the storage box garnish (A).
|
| 4. |
Remove the console upper cover (A).
|
| 5. |
Disconnect the floor console extension wiring (A) after removing the fastener.
|
| 6. |
Disconnect the connector (A, B, C, D ,E ,F ,G ,H).
A : WPC connector
B : WPC lamp connector
C : Driver parking assistance switch connector
D : SBW connector
E : SBW lamp connector
F : Fingerprint recognition unit connector
G : Floor console switch
H : SSB connector
|
| Installation |
| 1. |
Install in the reverse order of removal.
|
| Disassembly |
|
| 1. |
Remove the dial type SBW.
(Refer to Motor and Reduction Gear System - "SBW(Shift By Wire)
Lever")
|
| 2. |
Remove the console upper center cover (A).
|
| 3. |
Remove the passenger side garnish after removing the screws.
|
| 4. |
Disconnect the button engine start switch connector (A).
|
| 5. |
Remove the button start switch garnish (A) after removing the screws.
|
| 6. |
Remove the button start switch (A) after removing the screws.
|
| 7. |
Remove the driver side garnish (A) after removing the screws.
|
| 8. |
Remove the console switch (A) after removing the screws.
|
| 9. |
Remove the fingerprint recognition unit (A) after removing the screws.
|
| 10. |
Remove the wireless charging unit (WPC) (A) after removing the screws.
|
| Reassembly |
|
| 1. |
Reassemble in the reverse order of disassembly.
|
| Removal |
| 1. |
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage
service interlock connector.
|
| 2. |
Separate the front console cover (A) after removing the fasteners.
|
| 3. |
Remove the front console cover (A) after disconnecting the connectors (B).
|
| Installation |
| 1. |
Install in the reverse order of removal.
|
Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Change of distance to empty when 100% charging
If the estimated distance to empty decreases because the Kia EV6 has adapted to your driving style or environmental conditions, the estimated range may increase again when the vehicle is driven according to efficient driving practices. The distance-to-empty value can be reset by a workshop, but this does not increase the actual battery range.Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Front seat adjustment for power seat: (if equipped)
Seat cushion tilt adjustment Forward/backward seat adjustment Seat cushion height adjustment Seatback angle adjustment The Kia EV6 power front seats can be adjusted using the electronic control switches located on the outside of the seat cushion.