Kia EV6: Body (Interior / Exterior / Electrical) / Front & Rear Bumper
Contents:
Bumper Mounting Bracket Removal and Installation
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedure.
|
|
Rear Bumper Mounting Bracket [Standard]
| 1. |
Remove the rear bumper assembly.
(Refer to Front & Rear Bumper - "Rear Bumper
Assembly")
|
| 2. |
Remove the bracket (A) after removing the screws.
|
Rear Bumper Mounting Bracket [Option]
| 1. |
Remove the rear bumper assembly.
(Refer to Front & Rear Bumper - "Rear Bumper
Assembly")
|
| 2. |
Remove the bracket (A) after removing the screws.
|
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedure.
|
|
| 1. |
Install in the reverse order of removal.
|
Front Bumper Assembly Components and Components Location
| Component and Component Location |
Front Bumper [Removal]
Front Bumper [Disassembly]
1. Front Bumper Harness 2. Front Bumper Energy
Absorber 3. Front Bumper Active Air Flap 4. Ultra Wide Band Unit 5. Front Ultrasonic Sensor 6. Front
Corner Radar 7. Front Corner Ultrasonic Sensor
|
8. Front Bumper Radiator Grille 9. License
Plate 10. Front Bumper Grille Piece 11. Front Bumper Molding 12. Front Bumper Lower Cover 13. Front
Bumper Upper Cover
|
Front Bumper Assembly Removal and Installation
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
Front Bumper Assembly
| 1. |
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage
service interlock connector.
| (1)
|
Open the front trunk (A).
|
| (2)
|
Open the auxiliary 12 V battery service cover (A).
|
| (3)
|
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).
Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)
|
|
| (4)
|
Disconnect the service interlock connector (A).
|
•
|
Wait more than 5 minutes for capacitor of the high voltage battery system to be
discharged completely.
|
|
•
|
When working on a vehicle during discharging the capacitor, it can cause an
electrical shock or injury, so follow the manual.
|
|
|
The service interlock connector cannot be completely removed.
|
|
|
| 2. |
Remove the fender garnish.
(Refer to Body Side Molding - "Fender Garnish")
|
| 3. |
Remove the fasteners (A).
|
| 4. |
Remove the screw (A) and fasteners (B).
|
| 5. |
Separate the front bumper assembly (A).
|
| 6. |
Remove the front bumper assembly after disconnecting the front bumper main connector (A).
|
Radiator Upper Cover
| 1. |
Remove the radiator upper cover (A) after removing the fasteners.
|
Clip position :
|
|
Radiator Upper Grille
| 1. |
Remove the front bumper assembly.
|
| 2. |
Remove the radiator upper cover.
|
| 3. |
Remove the radiator upper grille (A) after removing the bolts.
Tightening torque :
7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)
|
|
| 4. |
Disconnect the wide angle front camera connector (A).
|
| 5. |
Disconnect the front center lamp connector (A). [Option type only]
|
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
| 1. |
Install in the reverse order of removal.
|
Front Bumper Assembly Disassembly and Reassembly
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
| 1. |
Remove the front corner radar.
(Refer to Advanced Driver Assistance Systems (ADAS) - "Front Corner
Radar")
|
| 2. |
Remove the front bumper wiring harness (A) after removing the fasteners.
|
Clip position :
|
|
| 3. |
Remove the front bumper energy absorber (A).
|
Clip position :
|
|
| 4. |
Remove the active air flap.
(Refer to Cooling System - "Active Air Flap (AAF)")
|
| 5. |
Remove the radiator grille (A) after removing the screws.
|
Clip position :
|
|
| 6. |
Remove the radiator grille (A) after removing the screws.
|
| 7. |
Remove the front bumper grille piece (A) after removing the screws.
|
Clip position :
|
|
| 8. |
Remove the front bumper molding (A).
|
Clip position :
|
|
| 9. |
Separate the front bumper upper cover (A) and lower cover (B) after removing the screw.
|
Clip position :
|
|
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
| 1. |
Install in the reverse order of removal.
|
Rear Bumper Assembly Components and Components Location
| Component and Component Location |
Rear Bumper [Removal]
1. Rear Bumper Under Cover 1-a. 15.7 - 23.5 N·m (1.6
- 2.4 kgf·m, 11.6 - 17.4 lb·ft) 2. Rear Bumper Rail Assembly 2-a. 15.7 - 23.5 N·m (1.6 - 2.4 kgf·m, 11.6 -
17.4 lb·ft)
|
3. Rear Bumper Assembly 3-a. 15.7 - 23.5 N·m (1.6 -
2.4 kgf·m, 11.6 - 17.4 lb·ft) 4. Rear Bumper Mounting Bracket 4-a. 6.9 - 10.2 N·m (0.7 - 1.04 kgf·m, 5.1 -
7.5 lb·ft)
|
Rear Bumper [Disassembly]
1. Rear Bumper Harness 2. Rear Bumper Rail
Assembly 3. Rear Bumper Reflector 4. Back Up Lamp 5. Rear Ultrasonic Sensor 6. Ultra Wide Band
Unit
|
7. Rear Corner Radar 8. Rear Corner Ultrasonic
Sensor 9. Rear Bumper Skid Plate 10. Rear Bumper Side Cover 11. Rear Bumper Cover
|
Rear Bumper Assembly Removal and Installation
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
| 1. |
Remove the outside rear combination lamp.
(Refer to Light & Vision System - "Rear Combination
Lamp")
|
| 2. |
Remove the quarter garnish.
(Refer to Body Side Molding - "Quarter Garnish")
|
| 3. |
Remove the rear bumper under cover (A) after removing the nuts and fasteners.
Tightening torque :
15.7 - 23.5 N·m (1.6 - 2.4 kgf·m, 11.6 - 17.4 lb·ft)
|
|
| 4. |
Remove the screw (A) and fasteners (B).
|
| 5. |
Remove the bolts (A).
Tightening torque :
15.7 - 23.5 N·m (1.6 - 2.4 kgf·m, 11.6 - 17.4 lb·ft)
|
[Driver's Side]
[Passenger's Side]
|
| 6. |
Remove the rear bumper (A) screws and fasteners.
[Driver's Side]
[Passenger's Side]
|
| 7. |
Separate the rear bumper assembly (A).
|
| 8. |
Disconnect the rear bumper main connector (A).
|
| 9. |
Remove the rear bumper assembly after disconnecting the rear bumper main connector (A).
|
Clip position :
|
|
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
| 1. |
Install in the reverse order of removal.
|
Rear Corner Radar Type
|
•
|
Use only genuine part for the bumper containing the rear corner radar.
|
|
•
|
Do not apply license plate molding or foreign objects such as a bumper sticker or a bumper
guard near the radar sensor. Doing so may adversely affect the sensing performance of the
radar.
|
|
•
|
The system may not work properly if paint repair is performed near the rear corner radar.
Be careful not to use a Polyester putty which has iron content.
|
|
•
|
The system may not work properly if the rear corner radar is covered with foreign matters,
such as snow, rain or dirt, etc.
|
|
•
|
The system may not work properly if the bumper around the rear corner radar is damaged or
sensor is out of position caused by the impact.
|
|
•
|
When installing the rear bumper, remove the foreign matter attached on the
exterior/interior label of the rear bumper.
(There must be no mechanical damage near the rear corner radar)
|
|
|
Rear Bumper Assembly Disassembly and Reassembly
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
| 1. |
Remove the rear bumper beam assembly.
(Refer to Front & Rear Bumper - "Rear Bumper Beam")
|
| 2. |
Remove the reflector (A) after removing the screws.
|
| 3. |
Remove the rear bumper skid plate (A) after removing the screws.
|
Clip position :
|
|
| 4. |
Remove the rear bumper side cover (A) after removing the screws..
|
Clip position :
|
|
| 5. |
Remove the rear bumper cover.
|
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
| 1. |
Install in the reverse order of removal.
|
Rear Bumper Beam Removal and Installation
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
| 1. |
Remove the rear bumper assembly.
(Refer to Front & Rear Bumper - "Rear Bumper
Assembly")
|
| 2. |
Remove the rear bumper wiring harness (A) after removing the fastener.
|
Clip position :
|
|
| 3. |
Remove the rear bumper beam assembly (A) after removing the fasteners.
|
Clip position :
|
|
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
| 1. |
Install in the reverse order of removal.
|
Other information:
Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Seat
The following section explains the names, functions, adjustment methods, and comfort features of each Kia EV6
seat.
The Kia EV6 seating system is designed to provide improved driving comfort, ergonomic support, passenger safety,
and
long-distance convenience for both the driver and passengers.
Seatback angle adjustment
Seat cushion height adjustment
Forward and backward seat movement
Seat cushion tilt adjustment
Lumbar support adjustment: (if equipped)
Seatback angle adjustment / folding function
Integrated memory seat system: (if equipped)
Rear seatback folding operation
Front headrest
Center armrest
Rear headrest
WARNING
Loose Objects
Do not place objects inside the Kia EV6 driver’s footwell area or underneath the front seats.
Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Highway Driving Assist settings
Driver Assistance
Driving Convenience
Highway Driving Assist
When the Kia EV6 is in DRIVE READY mode, tap Setup > Vehicle
>
Driver Assistance > Driving Convenience on the infotainment system screen
to
set the available options for each related function.
When Highway Driving Assist is selected, the system helps maintain distance from the vehicle ahead,
maintain
the set speed, and keep the Kia EV6 centered in the lane while driving on supported highways.

Contents
Categories