Kia EV6: Body (Interior / Exterior / Electrical) / Front Door

Contents:

Components and Components Location

Component and Component Location
Front Door [Trim]

Body (Interior / Exterior / Electrical) — Front Door / Components and Components Location / Component and Component Location illustration

1. Front Door Trim
2. Front Door Inside Handle
3. Main Power Window Switch
4. Sub Power Window Switch
5. Front Door Belt Inside Weatherstrip
6. Front Door Belt Outside Weatherstrip
7. Front Door Frame Molding
8. Front Door Frame Garnish
9. Front Door Body Side Weatherstrip
10. Front Door Side Weatherstrip.

Front Door [Mechanism]

Body (Interior / Exterior / Electrical) — Front Door / Components and Components Location / Component and Component Location illustration

1. Front Door Module
1-a. 8.8 - 11.8 N·m (0.9 - 1.2 kgf·m, 6.5 - 8.7 lb·ft)
2. Front Door Latch
2-a. 6.9 - 10.8 N·m (0.7 - 1.1 kgf·m, 5.1 - 8.0 lb·ft)
3. Front Door Speaker
4. Front Door Window Glass
4-a. 8.8 - 11.8 N·m (0.9 - 1.2 kgf·m, 6.5 - 8.7 lb·ft)
5. Front Door Glass Run
6. Front Door Latch
6-a. 6.9 - 10.8 N·m (0.7 - 1.1 kgf·m, 5.1 - 8 lb·ft)
7. Front Door Outside Handle
7-a. 3.4 - 5.7 N·m (0.35 - 0.58 kgf·m, 2.5 - 4.2 lb·ft, 30.4 - 50.3 lb·in)

Adjustment

Adjustment
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Door Adjustment
1.
Check that the gap between the door and the body is even after parking in a flat level.

Body (Interior / Exterior / Electrical) — Front Door / Adjustment illustration

2.
Loosen the door hinge (A) bolts (B), adjust the door (C) by moving it back and forth, left and right, and then tighten the bolts.

Tightening torque :
21.6 - 26.5 N·m (2.2 - 2.7 kgf·m, 15.9 - 19.5 lb·ft)

Body (Interior / Exterior / Electrical) — Front Door / Adjustment illustration

Body (Interior / Exterior / Electrical) — Front Door / Adjustment illustration

3.
Check that the gap between the door and the body is even.
Striker Adjustment
1.
Loosen the screws (B) and adjust the striker (A) by moving it back and forth, left and right, and then tighten the screws.

Tightening torque :
18.6 - 33.3 N·m (1.9 - 3.4 kgf·m, 13.7 - 24.6 lb·ft)

Body (Interior / Exterior / Electrical) — Front Door / Adjustment illustration

2.
Check that the door opens and closes properly.
Glass Adjustment
Note
Check the damage of the glass run and channel and replace them if necessary.
1.
Remove the front door trim.
(Refer to Front Door - "Front Door Trim")
2.
Adjust the gap by moving the window glass (A) up, down, left and right, and then tighten the bolts.

Tightening torque :
8.8 - 11.8 N·m (0.9 - 1.2 kgf·m, 6.5 - 8.7 lb·ft)

Body (Interior / Exterior / Electrical) — Front Door / Adjustment illustration

3.
Check the window glass for normal operation.
Window Motor Reset
1.
With the window open, use the auto/manual up switch to completely close the window and keep it closed for more than 0.2 seconds.
(If you operate the up switch while the window is completely closed, it will not be initialized)

On Vehicle Inspection

On Vehicle Inspection
Diagnostic with KDS
1.
The front door can quickly diagnosed for problems with the KDS. (Refer to "DTC guide")
(1)
Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS.
(Refer to DTC guide when fault code is found.)
Information
Refer to the KDS screen for operating conditions and details
Protection of Window Motor Overheating
1.
The motor can continuously operate at least 15 strokes, and it can be operated again 30 to 40 seconds after the motor stops due to the overheat protection function.

Front Door Garnish and Molding Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Door Frame Molding
1.
Remove the molding (A).

Body (Interior / Exterior / Electrical) — Front Door / Front Door Garnish and Molding / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Front Door / Front Door Garnish and Molding / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Front Door / Front Door Garnish and Molding / Removal and Installation / Removal illustration

Door Frame Garnish
1.
Remove the garnish (A).

Body (Interior / Exterior / Electrical) — Front Door / Front Door Garnish and Molding / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Front Door / Front Door Garnish and Molding / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Front Door / Front Door Garnish and Molding / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Front Door Handle Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Door Inside Handle
1.
Remove the front door trim.
(Refer to Front Door - "Front Door Trim")
2.
Remove the handle (A) after removing the screws.

Body (Interior / Exterior / Electrical) — Front Door / Front Door Handle / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Front Door / Front Door Handle / Removal and Installation / Removal illustration

Door Outside Handle
1.
Remove the front door module.
(Refer to Front Door - "Front Door Module")
2.
Remove the bolt (A).

Tightening torque :
8.8 - 11.8 N·m (0.9 - 1.2 kgf·m, 6.5 - 8.7 lb·ft)

Body (Interior / Exterior / Electrical) — Front Door / Front Door Handle / Removal and Installation / Removal illustration

3.
Remove the door lock assembly (A) by pulling it in the direction of the arrow.

Body (Interior / Exterior / Electrical) — Front Door / Front Door Handle / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Front Door / Front Door Handle / Removal and Installation / Removal illustration

4.
Disconnect the handle connector (A).

Body (Interior / Exterior / Electrical) — Front Door / Front Door Handle / Removal and Installation / Removal illustration

5.
Separate the handle wiring (A).

Body (Interior / Exterior / Electrical) — Front Door / Front Door Handle / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Front Door / Front Door Handle / Removal and Installation / Removal illustration

6.
Separate the latch rod (A).

Body (Interior / Exterior / Electrical) — Front Door / Front Door Handle / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Front Door / Front Door Handle / Removal and Installation / Removal illustration

7.
Remove the handle (A) after removing the nuts.

Tightening torque :
3.4 - 5.7 N·m (0.35 - 0.58 kgf·m, 2.5 - 4.2 lb·ft)

Body (Interior / Exterior / Electrical) — Front Door / Front Door Handle / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Front Door / Front Door Handle / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Front Door Latch Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Remove the front door module.
(Refer to Front Door - "Front Door Module")
2.
Disconnect the outside handle connector (A).

Body (Interior / Exterior / Electrical) — Front Door / Front Door Latch / Removal and Installation / Removal illustration

3.
Separate the outside handle wiring (A).

Body (Interior / Exterior / Electrical) — Front Door / Front Door Latch / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Front Door / Front Door Latch / Removal and Installation / Removal illustration

4.
Remove the screws (A).

Tightening torque :
6.9 - 10.8 N·m (0.7 - 1.1 kgf·m, 5.1 - 8.0 lb·ft)

Body (Interior / Exterior / Electrical) — Front Door / Front Door Latch / Removal and Installation / Removal illustration

5.
Remove the latch (B) after separating the latch rod (A).

Body (Interior / Exterior / Electrical) — Front Door / Front Door Latch / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Front Door / Front Door Latch / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Front Door / Front Door Latch / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Front Door Latch Inspection

Inspection
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Remove the front door latch.
(Refer to Front Door - "Front Door Latch")
2.
Apply voltage to connector terminal and check that the door latch operates properly.

Body (Interior / Exterior / Electrical) — Front Door / Front Door Latch / Inspection illustration

Location
Terminal
Driver
7, 8
Passenger
1, 2

Front Door Module Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Remove the front door window glass.
(Refer to Front Door - "Front Door Window Glass")
2.
Disconnect the door main wiring connector (A).

Body (Interior / Exterior / Electrical) — Front Door / Front Door Module / Removal and Installation / Removal illustration

3.
Disconnect the outside mirror connector (A).

Body (Interior / Exterior / Electrical) — Front Door / Front Door Module / Removal and Installation / Removal illustration

4.
Separate the door module (A) after removing the bolts.

Tightening torque :
8.8 - 11.8 N·m (0.9 - 1.2 kgf·m, 6.5 - 8.7 lb·ft)

Body (Interior / Exterior / Electrical) — Front Door / Front Door Module / Removal and Installation / Removal illustration

5.
Remove the door module after disconnecting the wiring connectors (A).

Body (Interior / Exterior / Electrical) — Front Door / Front Door Module / Removal and Installation / Removal illustration

6.
Separate the wiring harness (A).

Body (Interior / Exterior / Electrical) — Front Door / Front Door Module / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Front Door Speaker Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Door Speaker
1.
Remove the front door trim.
(Refer to Front Door - "Front Door Trim")
2.
Separate the speaker connector (A).

Body (Interior / Exterior / Electrical) — Front Door / Front Door Speaker / Removal and Installation / Removal illustration

3.
Remove the speaker (A) after removing the bolts.

Tightening torque :
7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)

Body (Interior / Exterior / Electrical) — Front Door / Front Door Speaker / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Front Door Switch Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Power Window Main Switch
1.
Remove the front door trim. [Driver's side]
(Refer to Front Door - "Front Door Trim")
2.
Remove the switch (A) by pulling the hook in the direction of the arrow.

Body (Interior / Exterior / Electrical) — Front Door / Front Door Switch / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Front Door / Front Door Switch / Removal and Installation / Removal illustration

Power Window Sub Switch
1.
Remove the passenger's side front door trim.
(Refer to Front Door - "Front Door Trim")
2.
Remove the switch (A) by pulling the hook in the direction of the arrow.

Body (Interior / Exterior / Electrical) — Front Door / Front Door Switch / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Front Door / Front Door Switch / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Front Door Trim Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
(1)
Open the front trunk (A).

Body (Interior / Exterior / Electrical) — Front Door / Front Door Trim / Removal and Installation / Removal illustration

(2)
Open the auxiliary 12 V battery service cover (A).

Body (Interior / Exterior / Electrical) — Front Door / Front Door Trim / Removal and Installation / Removal illustration

(3)
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).

Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)

Body (Interior / Exterior / Electrical) — Front Door / Front Door Trim / Removal and Installation / Removal illustration

(4)
Disconnect the service interlock connector (A).

Body (Interior / Exterior / Electrical) — Front Door / Front Door Trim / Removal and Installation / Removal illustration

Warning
•
Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
•
When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
Note
The service interlock connector cannot be completely removed.

Body (Interior / Exterior / Electrical) — Front Door / Front Door Trim / Removal and Installation / Removal illustration

2.
Separate the quadrant inner cover (A).

Body (Interior / Exterior / Electrical) — Front Door / Front Door Trim / Removal and Installation / Removal illustration

3.
Remove the quadrant inner cover (A) after disconnecting the tweeter speaker connector.

Body (Interior / Exterior / Electrical) — Front Door / Front Door Trim / Removal and Installation / Removal illustration

4.
Separate the door trim (A) after removing the screw.

Body (Interior / Exterior / Electrical) — Front Door / Front Door Trim / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Front Door / Front Door Trim / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Front Door / Front Door Trim / Removal and Installation / Removal illustration

5.
Remove the door trim after disconnecting the connectors (A).

Body (Interior / Exterior / Electrical) — Front Door / Front Door Trim / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Front Door / Front Door Trim / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Front Door Weatherstrip Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Door Side Weatherstrip
1.
Separate the door checker (A) after removing the bolt.

Tightening torque :
21.6 - 32.4 N·m (2.2 - 3.3 kgf·m, 15.9 - 23.9 lb·ft)

Body (Interior / Exterior / Electrical) — Front Door / Front Door Weatherstrip / Removal and Installation / Removal illustration

2.
Remove the weatherstrip (A).

Body (Interior / Exterior / Electrical) — Front Door / Front Door Weatherstrip / Removal and Installation / Removal illustration

Door Body Side Weatherstrip
1.
Remove the weatherstrip (A).

Body (Interior / Exterior / Electrical) — Front Door / Front Door Weatherstrip / Removal and Installation / Removal illustration

Door Belt Outside Weatherstrip
1.
Remove the weatherstrip (A).

Body (Interior / Exterior / Electrical) — Front Door / Front Door Weatherstrip / Removal and Installation / Removal illustration

Door Belt Inside Weatherstrip
1.
Remove the front door trim.
(Refer to Front Door - "Front Door Trim")
2.
Remove the weatherstrip (A).

Body (Interior / Exterior / Electrical) — Front Door / Front Door Weatherstrip / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Front Door Window Glass Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Door Window Glass
1.
Remove the front door belt inside and outside weatherstrips.
(Refer to Front Door - "Front Door Weatherstrip")
2.
Lower it until window glass bolt is exposed in the hold plug by operating the power window switch.
3.
remove the window glass (A) after removing the bolts.

Tightening torque :
8.8 - 11.8 N·m (0.9 - 1.2 kgf·m, 6.5 - 8.7 lb·ft)

Body (Interior / Exterior / Electrical) — Front Door / Front Door Window Glass / Removal and Installation / Removal illustration

Door Window Glass Run
1.
Remove the door window glass.
2.
Remove the front door frame garnish and molding.
(Refer to Front Door - "Front Door Frame Garnsih and Moilding")
3.
Remove the glass run (A).

Body (Interior / Exterior / Electrical) — Front Door / Front Door Window Glass / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Front Door Window Motor Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Power Window Motor
1.
Remove the front door trim.
(Refer to Front Door - "Front Door Trim")
2.
Remove the motor connector (A).

Body (Interior / Exterior / Electrical) — Front Door / Front Door Window Motor / Removal and Installation / Removal illustration

3.
Remove the motor (A) after removing the bolts.

Tightening torque :
7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)

Body (Interior / Exterior / Electrical) — Front Door / Front Door Window Motor / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.
2.
Perform the window motor reset procedure.
(Refer to Front Door - "Adjustment")

Other information:

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: A Guide to Storage, Transport and Disposal of Old Battery Systems

Used high voltage battery system storage, transportation, disposal guide • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training.

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Wide Angle Camera Adjustment

Adjustment Tolerance Calibration Outline Tolerance calibration compensates for the error margins of surround view video that occur due to the installation tolerance when the four cameras that comprise the SVM system are installed. Tolerance calibration must be performed when the following actions are performed.

 
Copyright © 2026 Kia EV6 Manuals ⏱ 0.0245