Contents:
| Component |

| 1. Front Brake Disc 1-a. 4.9 - 5.9 N·m (0.5 - 0.6 kgf·m, 3.6 - 4.3 lb·ft, 43.4 - 52.1 lb·in) 2. Front Dust Cover 2-a. 6.9 - 10.8 N·m (0.7 - 1.1 kgf·m, 5.1 - 8.0 lb·ft, 60.8 - 95.5 lb·in) 3. Front Hub Assembly 3-a. 127.5 - 147.1 N·m (13.0 - 15.0 kgf·m, 94.0 - 108.5 lb·ft) |
4. Front Knuckle 4-a. 156.9 - 176.5 N·m (16.0 - 18.0 kgf·m, 115.7 - 130.2 lb·ft) 4-b. 98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft) 4-c. 98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft) |
| Removal |
| 1. |
Remove the front wheel and tires.
(Refer to Suspension System - "Wheel")
|
| 2. |
Disconnect the front wheel speed sensor connector (A).
|
| 3. |
Remove the front brake disc.
(Refer to Brake System - "Front Brake Disc")
|
| 4. |
Remove the front hub assembly (B) after removing the front hub assembly bolts (A).
|
| Installation |
| 1. |
Install in the reverse order of removal.
|
| Special Service Tool |
|
Tool Name / Number |
Illustration |
Description |
|
CV joint puller 09517 - 4E000 |
|
Used for removal of CV joint |
| Removal |
| 1. |
Remove the front wheel and tires.
(Refer to Suspension System - "Wheel")
|
| 2. |
Unlock the driveshaft lock nut caulking (A), by hammering on a chisel or suitable tool.
|
| 3. |
Remove the driveshaft lock nut (A).
|
| 4. |
Separate the front driveshaft (A) from the front axle by using the SST (09517 - 4E000).
|
| 5. |
Remove the front brake disc.
(Refer to Brake System - "Front Brake Disc")
|
| 6. |
Remove the front hub assembly (B) after removing the front hub assembly bolts (A).
|
| Installation |
| 1. |
Install in the reverse order of removal.
|
| Inspection |
| 1. |
Check the hub for cracks and spline wear.
|
| 2. |
Check the hub bearing for defects.
|
| Removal |
| 1. |
Remove the front brake disc.
(Refer to Brake System - "Front Brake Disc")
|
| 2. |
Remove the front dust cover (A) after removing the bolts.
|
| Installation |
| 1. |
Install in the reverse order of removal.
|
| Inspection |
| 1. |
Check the dust cover for cracks.
|
| Special Service Tool |
|
Tool Name / Number |
Illustration |
Description |
|
Ball joint puller 09568 - 2J100 |
|
Used for removal of tie rod end |
|
Lower arm ball joint remover 0K545 - A9100 |
|
Used for removal of front lower arm ball joint |
| Removal |
| 1. |
Remove the front wheel and tires.
(Refer to Suspension System - "Wheel")
|
| 2. |
Disconnect the front wheel speed sensor connector (A).
|
| 3. |
Separate the tie rod end ball joint from the front axle.
|
| 4. |
Remove the front brake disc.
(Refer to Brake System - "Front Brake Disc")
|
| 5. |
Separate the lower arm ball joint from the front axle using SST (0K545 - A9100).
|
| 6. |
Remove the front axle assembly (A) after removing the bolts and nuts.
|
| 7. |
Remove the dust cover (A) after removing the bolts.
|
| 8. |
Remove the front hub assembly (B) after removing the front hub assembly bolts (A).
|
| Installation |
| 1. |
Install in the reverse order of removal.
|
| 2. |
Check the alignment.
(Refer to Suspension System - "Alignment")
|
| Special Service Tool |
|
Tool Name / Number |
Illustration |
Description |
|
Ball joint puller 09568 - 2J100 |
|
Used for removal of tie rod end |
|
CV joint puller 09517 - 4E000 |
|
Used for removal of CV joint |
|
Lower arm ball joint remover 0K545 - A9100 |
|
Used for removal of front lower arm ball joint |
| Removal |
| 1. |
Remove the front wheel and tires.
(Refer to Suspension System - "Wheel")
|
| 2. |
Remove the front wheel speed sensor (A) after removing the bolt.
|
| 3. |
Unlock the driveshaft lock nut caulking (A), by hammering on a chisel or suitable tool.
|
| 4. |
Remove the driveshaft lock nut (A).
|
| 5. |
Separate the front driveshaft (A) from the front axle by using the SST (09517 - 4E000).
|
| 6. |
Separate the tie rod end ball joint from the front axle.
|
| 7. |
Remove the front brake disc.
(Refer to Brake System - "Front Brake Disc")
|
| 8. |
Separate the lower arm ball joint from the front axle using SST (0K545 - A9100).
|
| 9. |
Remove the front axle assembly (A) after removing the bolts and nuts.
|
| 10. |
Remove the dust cover (A) after removing the bolts.
|
| 11. |
Remove the front hub assembly (B) after removing the front hub assembly bolts (A).
|
| Installation |
| 1. |
Install in the reverse order of removal.
|
| 2. |
Check the alignment.
(Refer to Suspension System - "Alignment")
|
| Inspection |
| 1. |
Check the front knuckle for cracks.
|
Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Driver Attention Warning (DAW)
Driver Attention Warning function The Kia EV6 Driver Attention Warning function monitors driving patterns, steering behavior, lane position, and vehicle movement to help determine whether driver attention may be decreasing. When the system determines that the driver’s attention level has dropped below a certain threshold, Driver Attention Warning may recommend taking a break to support safer driving.Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: If the Vehicle Will Not Start
The Kia EV6 may fail to start if the 12-volt battery charge is insufficient or if a related electrical issue is present. Check the battery condition by performing the following steps: Verify that the shifter dial is positioned in P (Park). The Kia EV6 can only be started when the transmission selector is in the Park position.