Kia EV6: Driveshaft and Axle

Contents:

Single-Use Parts

Single-Use Parts
Non-reusable parts (Single-Use Parts)
Workshop manual provides “Components and Components Location” which can be used to identify “Non-reusable parts”. When repairing a vehicle, Non-reusable parts such as fasteners, gaskets, washers, clips and garnishes must be replaced. Kia Non-reusable parts are designed to be installed only once.
Before working on a vehicle, check “Components and Components Location” to find the non-reusable parts in a system.
※ Symbol of Non-reusable parts
Symbol
Meaning

Driveshaft and Axle — Single-Use Parts illustration

Do not reuse the part. Replace with a new one.

※ Example of “Components and Components Location”

Driveshaft and Axle — Single-Use Parts illustration

High Voltage System General Safety Information and Caution ➤

High Voltage Shut-off Procedures

High Voltage Shut-off Procedures

High Voltage Shut-off Procedures
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Information
High Voltage Component : Battery System Assembly (BSA), motor assembly, inverter assembly, high voltage junction box, power cable, etc.
1.
Check the Battery Management Unit (BMU) weld flag with the KDS.
(Data Analysis → Battery Management System (BMS) → BMU Weld Flag)

Specified value : NO

Information
Refer to the KDS screen for operating conditions and details.
2.
Open the front trunk (A).

Driveshaft and Axle — High Voltage Shut-off Procedures illustration

3.
Open the low voltage (12 V) battery service cover (A).

Driveshaft and Axle — High Voltage Shut-off Procedures illustration

4.
Turn the POWER OFF, separate the low voltage (12 V) battery ( - ) terminal (A).

Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)

Driveshaft and Axle — High Voltage Shut-off Procedures illustration

5.
Disconnect the service interlock connector (A).

Driveshaft and Axle — High Voltage Shut-off Procedures illustration

Warning
•
Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
•
When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
Note
The service interlock connector cannot be completely removed.

Driveshaft and Axle — High Voltage Shut-off Procedures illustration

6.
Remove the front under cover.
(Refer to Motor and Reduction Gear System - "Front Under Cover")
7.
Remove the high voltage battery cover (A).

Tightening torque :
7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)

Driveshaft and Axle — High Voltage Shut-off Procedures illustration

8.
Disconnect the front high voltage junction box power cable (A).

Driveshaft and Axle — High Voltage Shut-off Procedures illustration

Note
How to disconnect the connector
1)
Release the locking clip (A) by pulling it.
2)
Disconnect the connector by pushing the lever (A) in the direction of the arrow while pressing the locking clip (B).

Driveshaft and Axle — High Voltage Shut-off Procedures illustration

9.
Remove the center floor rear under cover.
(Refer to Motor and Reduction Gear System - "Rear Under Cover")
10.
Disconnect the Integrated Charge Control Unit (ICCU) connector (A).

Driveshaft and Axle — High Voltage Shut-off Procedures illustration

Note
How to disconnect the connector
1)
Release the locking clip (A) by pulling it.
2)
Disconnect the connector while pressing the locking clip (B).

Driveshaft and Axle — High Voltage Shut-off Procedures illustration

11.
Disconnect the rear high voltage junction box power cable (A).

Driveshaft and Axle — High Voltage Shut-off Procedures illustration

Note
How to disconnect the connector
1)
Release the locking clip (A) by pulling it.
2)
Disconnect the connector by pushing the lever (A) in the direction of the arrow while pressing the locking clip (B).

Driveshaft and Axle — High Voltage Shut-off Procedures illustration

12.
Measure the voltage between the high voltage power connector and high voltage battery terminal to check whether the high voltage is shut-off.

30 V or less : Normal cut off high voltage circuit
Above 30 V : Fault on high voltage circuit

(1)
Measure the voltage between the high voltage power connector positive ( + ) terminal and negative ( - ) terminal.

Driveshaft and Axle — High Voltage Shut-off Procedures illustration

(2)
Measure the voltage between the high voltage battery positive ( + ) and negative ( - ) terminal.

Driveshaft and Axle — High Voltage Shut-off Procedures illustration

(3)
Measure the voltage between the high voltage battery positive ( + ) terminal and ground.

Driveshaft and Axle — High Voltage Shut-off Procedures illustration

(4)
Measure the voltage between the high voltage battery negative ( - ) terminal and ground.

Driveshaft and Axle — High Voltage Shut-off Procedures illustration

(5)
Measure the voltage between the rear high voltage battery positive ( + ) and negative ( - ) terminal.

Driveshaft and Axle — High Voltage Shut-off Procedures illustration

(6)
Measure the voltage between the rear high voltage battery positive ( + ) terminal and ground.

Driveshaft and Axle — High Voltage Shut-off Procedures illustration

(7)
Measure the voltage between the rear high voltage battery negative ( - ) terminal and ground.

Driveshaft and Axle — High Voltage Shut-off Procedures illustration

Warning
1)
Check for insulation breakdown via KDS and physical leakage current before working on EV.
2)
Remove the main fuse if insulation breakdown or leakage current is suspected. (Remove the main fuse even when DTC CODE ON such as PRA malfunction)
(Refer to High Voltage Battery Control System - "Main Fuse")
※ If there is no insulation breakdown or leakage current and it is normal, work without removing the main fuse.

Specification ➤

Special Service Tool

Special Service Tool
Tool Name / Number
Illustration
Description
Ball joint puller
09568 - 2J100

Driveshaft and Axle — Special Service Tool illustration

Used for removal of tie rod end
CV joint puller
09517 - 4E000

Driveshaft and Axle — Special Service Tool illustration

Used for removal of CV joint
Lower arm ball joint remover
0K545 - A9100

Driveshaft and Axle — Special Service Tool illustration

Used for removal of front lower arm ball joint
Band installer
0K495 - C5000

Driveshaft and Axle — Special Service Tool illustration

Used for installing ear type boot band(Sharing handle with 0K495 - 2W000)
Band installer
0K495 - 2W001

Driveshaft and Axle — Special Service Tool illustration

Used for installing hook type boot band (low profile)
Band installer
09495 - 39100

Driveshaft and Axle — Special Service Tool illustration

Used for installing hook type boot band

Troubleshooting

Troubleshooting
Symptom
Suspected causes
Correction
Drive Train
2WD
4WD
Vehicle pulls to one side
Defect on front suspension and steering gear.
Adjust or replace
●
●
Wheel bearing seized
Replacement
●
●
Unbalanced wear of tires
Wheel alignment adjustment
●
●
Vibration
Over abrasion, separation, damaged or bent on driveshaft
Replacement
(Replacement using repair kit)
X
●
Wheel bearing excessive play
Replacement
●
●
Shimmy
Inappropriate wheel balance
Adjust or replace
●
●
Defect on front suspension and steering gear.
Adjust or replace
●
●
Noise
Excessive worn, damaged, or bent driveshaft
Replacement
(Replacement using repair kit)
X
●
Noise on connecting part of driveshaft and hub while driving straight, back or curve (Clicking or Creaking noise)
Tighten hub nuts
or inner washer replacement
X
●
Noise from the inner side of the shaft while driving curve (Repeated tapping noise)
Replacement
(Replacement using repair kit)
X
●
Friction noise on driveshaft boots (Sticky noise)
Clean and apply fluorine lubricant
X
●
Loosen hub nut
Adjust
X
●
Defect on front suspension and steering gear.
Adjust or replace
●
●
Loosen disc screw
Adjustment
●
●
Noise on the wheel bearing while driving (Whir noise)
Replacement
●
●
Wheel bearing has excessive play, the contacted surface of flange burnt
Replacement
●
●
Leakage
Leakage of grease on driveshaft boots (partial parts replacement when inboard side boots have leakage)
Replacement
(Replacement using repair kit)
X
●
Rust
Corrosion on nonpainting area (Not a problem for functioning)
Explain to the customer it is normal
●
●
ABS warning lamp illuminated
Loosen wheel bearing sensor and sensor cable
Adjustment
●
●
Contaminated wheel bearing sensor connector
Cleaning
●
●
Communication error (Diagnosis using KDS)
Adjustment
●
●
Integrated Drove Axle (IDA)
Noise / Vibration / Leakage
Refer to IDA troubleshooting by symptom type.
(Refer to Integrated Drive Axle (IDA) - "Troubleshooting")
←
●
●

Front Axle Assembly ➤

Front Driveshaft Assembly (4WD) ➤

Rear Driveshaft & Axle Assembly ➤

Other information:

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: EV Economy History

You can review the Kia EV6 energy consumption history together with driving dates and travel distances from previous trips. The system highlights the most energy-efficient driving record using a dedicated efficiency icon.

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Shifting conditions not met, Reduce speed, then shift

A: Shifting conditions not met, Reduce speed, then shift This Kia EV6 message appears on the LCD instrument cluster display under the following operating conditions: The Kia EV6 is traveling at a speed that is too high to safely change gear positions. Reduce vehicle speed before attempting to shift gears.

Contents

Categories

 
Copyright © 2026 Kia EV6 Manuals ⏱ 0.0154