Kia EV6: Driveshaft and Axle / Front Driveshaft Assembly (4WD)

Contents:

Front Driveshaft Components and Components Location

Component

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Front Driveshaft / Components and Components Location / Component illustration

1. Housing (Wheel Side)
2. Driveshaft Boot Band
3. Driveshaft Boot
4. Shaft Assembly
5. Spider Assembly
6. Snap Ring
7. Housing (Reduction Gear Side)

Front Driveshaft Removal and Installation

Special Service Tool
Tool Name / Number
Illustration
Description
Ball joint puller
09568 - 2J100

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Front Driveshaft / Removal and Installation / Special Service Tool illustration

Used for removal of tie rod end
CV joint puller
09517 - 4E000

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Front Driveshaft / Removal and Installation / Special Service Tool illustration

Used for removal of CV joint
Lower arm ball joint remover
0K545 - A9100

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Front Driveshaft / Removal and Installation / Special Service Tool illustration

Used for removal of front lower arm ball joint

Removal
Warning
•
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
•
When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
1.
Disconnect the battery negative ( - ) terminal and the service interlock connector.
(Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
2.
Remove the front wheel and tires.
(Refer to Suspension System - "Wheel")
3.
Remove the stabilizer bar link (A) from the front strut assembly after removing the nut.

Tightening torque :
98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Front Driveshaft / Removal and Installation / Removal illustration

Note
•
Hold the outer hex (A) when removing or installing the nut (B).

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Front Driveshaft / Removal and Installation / Removal illustration

•
Be careful not to damage the boot of the link.
•
Use a hand tool when removing or installing the stabilizer bar link nut.
4.
Separate the tie rod end ball joint from the front axle.
(1)
Remove the split pin (A).
(2)
Remove the lock nut (B), and washer (C).

Tightening torque :
98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Front Driveshaft / Removal and Installation / Removal illustration

Note
•
Do not reuse the split pin.
•
Do not reuse the lock nut.
•
Be careful not to damage the boot of the link.
•
Use a hand tool when removing or installing the lock nut.
(3)
Separate the tie rod end ball joint (A) using SST (09568 - 2J100).

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Front Driveshaft / Removal and Installation / Removal illustration

5.
Separate the lower arm ball joint from the front axle using SST (0K545 - A9100).
(1)
Remove the split pin (D).
(2)
Remove the lower arm bolt (A), washer (B), and nut (C).

Tightening torque :
98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Front Driveshaft / Removal and Installation / Removal illustration

Information
Fix the lower arm ball joint bolt and remove or install the nut.
Note
•
Do not reuse the split pin.
•
Be careful not to change the position of the bolt, nut, and washer when installing.
(3)
Place the support bolts (A) to the lower arm ball joint mounting hole, and then rotate them to install the SST.

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Front Driveshaft / Removal and Installation / Removal illustration

Information
Use the support body (A) of the SST (0K545 - A9100).

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Front Driveshaft / Removal and Installation / Removal illustration

(4)
Install the support body (B) in the front axle groove (A).

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Front Driveshaft / Removal and Installation / Removal illustration

(5)
Rotate the bolt (A) to insert the support body (B) to release the front knuckle.

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Front Driveshaft / Removal and Installation / Removal illustration

(6)
Install the main body (A) between the front strut assembly and front lower arm.

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Front Driveshaft / Removal and Installation / Removal illustration

Information
Use the main body (A) of the SST (0K545 - A9100).

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Front Driveshaft / Removal and Installation / Removal illustration

(7)
Secure the main body with the wire (A) to prevent it from falling.

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Front Driveshaft / Removal and Installation / Removal illustration

(8)
Install the c-clamp (A) by rotating the handle (B) to prevent the main body from slipping.

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Front Driveshaft / Removal and Installation / Removal illustration

Information
Use the C-clamp (A) of the SST (0K545 - A9100).

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Front Driveshaft / Removal and Installation / Removal illustration

(9)
Tighten the bolt (A) to widen the gap of the main body so that the front lower arm can be removed from the front knuckle.

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Front Driveshaft / Removal and Installation / Removal illustration

6.
Unlock the driveshaft lock nut caulking (A), by hammering on a chisel or suitable tool.

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Front Driveshaft / Removal and Installation / Removal illustration

7.
Remove the driveshaft lock nut (A).

Tightening torque :
294.2 - 313.8 N·m (30.0 - 32.0 kgf·m, 217 - 231.5 lb·ft)

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Front Driveshaft / Removal and Installation / Removal illustration

8.
Separate the front driveshaft (A) from the front axle by using the SST (09517 - 4E000).

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Front Driveshaft / Removal and Installation / Removal illustration

9.
Separate the front axle assembly (A) and front driveshaft (B).

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Front Driveshaft / Removal and Installation / Removal illustration

Note
When removing the driveshaft, do not force pull or over bend the axle.
10.
Remove the front under cover.
(Refer to Motor and Reduction Gear System - "Front Under Cover")
11.
Remove the driveshaft (A) using the pry bar (B).

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Front Driveshaft / Removal and Installation / Removal illustration

Note
•
Do not insert the pry bar too deep, as this may damage the oil seal.
•
Do not pull the driveshaft with excessive force. it may cause internal damage or dislocation.
•
Plug the hole of the reduction gear case with the oil seal cap to prevent contamination.
•
Support the driveshaft properly.
Installation
Warning
•
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
•
When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
1.
Install in the reverse order of removal.
Note
•
Do not reuse the driveshaft lock nut.
•
After tightening the driveshaft lock nut, caulk the lock nut to an appropriate depth (A) by using a chisel or suitable tool.

Caulking Depth (A) :
1.5 mm (0.0590 in.) or more

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Front Driveshaft / Removal and Installation / Installation illustration

•
Press the brake pedal to prevent the driveshaft from rotating when tightening the driveshaft lock nut.
•
The existing front driveshaft circlip (A) should be replaced with new one (do not reuse).

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Front Driveshaft / Removal and Installation / Installation illustration

Joint Assembly (Wheel side) Removal

Removal
When able to replace the wheel side joint boot
1.
Remove the front driveshaft.
(Refer to Front Driveshaft Assembly (4WD) - "Front Driveshaft")
2.
Remove the reduction gear side joint.
(Refer to Front Driveshaft Assembly (4WD) - "Joint Assembly (Reduction Gear Side)")
3.
Remove the wheel side joint small diameter (A) and large diameter (B) boot band using a flat-head driver.

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Wheel side) / Removal illustration

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Wheel side) / Removal illustration

4.
Remove the wheel side joint boot (A).

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Wheel side) / Removal illustration

Note
•
Do not remove the wheel side joint housing (A).
•
Reinstall the wheel side joint housing (A) may cause leakage, so replace it with the shaft (B) as an assembly.

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Wheel side) / Removal illustration

When unable to replace the wheel side joint boot
1.
Remove the front driveshaft.
(Refer to Front Driveshaft Assembly (4WD) - "Front Driveshaft")
2.
Remove the reduction gear side joint.
(Refer to Front Driveshaft Assembly (4WD) - "Joint Assembly (Reduction Gear Side)")
3.
Replace the wheel side joint assembly (A) and shaft (B).

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Wheel side) / Removal illustration

Note
The wheel side joint boot can not be replaced, so replace the wheel side joint assembly (A) and shaft (B) together as an assembly.

Joint Assembly (Wheel side) Installation

Special Service Tool
Tool Name / Number
Illustration
Description
Band installer
0K495 - C5000

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Wheel side) / Installation / Special Service Tool illustration

Used for installing of ear type boot band
(Sharing handle with 0K495 - 2W000)

Installation
When able to replace the wheel side joint boot
Caution
•
When assembling, be careful not to let dust and foreign substances enter.
•
Driveshaft joints require special grease, so do not add any other type of grease.
•
When replacing the boot band, it must be a new one.
1.
Install the new boot (A) in the direction of the arrow.

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Wheel side) / Installation illustration

2.
Apply the specified grease inside the boot.

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Wheel side) / Installation illustration

Note
•
Use the grease provided with the joint/boot kit.
•
Apply about 50 - 60% grease inside the boot.
•
Driveshaft joints require special grease, so do not add any other type of grease.
3.
Install the wheel side boot (A) into the housing (B).

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Wheel side) / Installation illustration

4.
Install the large diameter boot band using SST (0K495 - C5000).

Clearance (A) :
2.0 mm (0.0787 in.) or less.

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Wheel side) / Installation illustration

5.
Install the small diameter boot band using SST (0K495 - C5000).

Clearance (A) :
2.0 mm (0.0787 in.) or less.

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Wheel side) / Installation illustration

Note
•
When installing the boot band, align the fastened direction with the wheel side joint large diameter boot band.

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Wheel side) / Installation illustration

•
Clean if there is any grease around the boot band after installing.
6.
Install the reduction gear side joint.
(Refer to Front Driveshaft Assembly (4WD) - "Joint Assembly (Reduction Gear Side)")
7.
Install the front driveshaft.
(Refer to Front Driveshaft Assembly (4WD) - "Front Driveshaft")
When unable to replace the wheel side joint boot
Note
•
When assembling, be careful not to let dust and foreign substances enter.
•
Driveshaft joints require special grease, so do not add any other type of grease.
•
When replacing the boot band, it must be a new one.
1.
Replace the wheel side joint assembly (A) and shaft (B).

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Wheel side) / Installation illustration

Note
The wheel side joint boot can not be replaced, so replace the wheel side joint assembly (A) and shaft (B) together as an assembly.
2.
Install the reduction gear side joint.
(Refer to Front Driveshaft Assembly (4WD) - "Joint Assembly (Reduction Gear Side)")
3.
Install the front driveshaft.
(Refer to Front Driveshaft Assembly (4WD) - "Front Driveshaft")

Joint Assembly (Wheel side) Inspection

Inspection
1.
Check the boot for water or foreign objects.
2.
Replace any defective parts.

Joint Assembly (Reduction gear side) Removal

Special Service Tool
Tool Name / Number
Illustration
Description
Band installer
0K495 - 2W001

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Removal / Special Service Tool illustration

Used for installing hook type boot band (low profile)

Removal
Note
•
Driveshaft joints require special grease, so do not add any other type of grease.
•
When replacing the boot band, it must be a new one.
1.
Remove the front driveshaft.
(Refer to Front Driveshaft Assembly (4WD) - "Front Driveshaft")
2.
Remove the reduction gear side large diameter (A) and small diameter (B) boot bands.

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Removal illustration

Information
Use the right tool for each type of boot band as shown in the table below.
Ear type
Hook type
Hook type
[Low profile]
Flat-head screwdriver
Flat-head screwdriver
SST (0K495 - 2W001)

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Removal illustration

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Removal illustration

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Removal illustration


Note
When using the low profile hook type boot band, fit the SST tip (B) into the boot band hole (A) as shown below.

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Removal illustration

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Removal illustration

3.
Remove the reduction gear side joint housing (A).

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Removal illustration

4.
Remove the snap ring (A) using a snap ring pliers.

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Removal illustration

5.
Remove the spider assembly (B) from the driveshaft using a puller (A).

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Removal illustration

Note
Be careful not to load the roller bearings when removing the spider assembly using a puller.
6.
Remove reduction gear side boot (A).

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Removal illustration

7.
Clean the inside of the spider assembly and joint housing.
Note
Remove grease inside the housing as much as possible.

Joint Assembly (Reduction gear side) Installation

Special Service Tool
Tool Name / Number
Illustration
Description
Band installer
0K495 - C5000

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Installation / Special Service Tool illustration

Used for installing of ear type boot band
(Sharing handle with 0K495 - 2W000)
Band installer
0K495 - 2W001

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Installation / Special Service Tool illustration

Used for installing hook type boot band (low profile)
Band installer
09495 - 39100

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Installation / Special Service Tool illustration

Used for installing hook type boot band

Installation
Note
•
When assembling, be careful not to let dust and foreign substances enter.
•
Driveshaft joints require special grease, so do not add any other type of grease.
•
When replacing the boot band, it must be a new one.
1.
Install the reduction gear side boot (A) and boot band (B) on the driveshaft.

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Installation illustration

Note
Put the boot band (B) first on the driveshaft before installing the boot (A).
2.
Install the spider assembly (A) on the shaft (B), then press it using a rubber mallet.

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Installation illustration

Note

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Installation illustration

•
When installing the spider assembly (A), install it in the correct direction.
•
Installing in the wrong direction can cause secondary quality problems.
3.
Install the snap ring (A) using the snap ring pliers.

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Installation illustration

Note
•
When replacing the joint assembly, use the new one provided in the joint kit.
•
Do not reuse the snap ring.
•
After installing the snap ring, make sure that there are only 2 - 3 splines in position (A).

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Installation illustration

4.
Install the reduction gear side joint boot (A) in the correct position.

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Installation illustration

Note
•
When installing boot (A), make sure the boot fits into the groove (B).

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Installation illustration

•
When installing the spider assembly, fit the assembly to the boot shape.

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Installation illustration

5.
Apply specified grease inside the joint housing (A) and boot (B).

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Installation illustration

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Installation illustration

Note
•
Use the grease provided with the joint/boot kit.
•
Apply about 70% grease to the housing (A) and about 30% grease to the boot (B).
•
Driveshaft joints require special grease, so do not add any other type of grease.
6.
Install the reduction gear side joint housing (A).

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Installation illustration

Note
•
When installing the housing, turn the boot to fit each other.
•
If the shape of housing and boot does not fit, there is a possibility of leakage due to the gap. Be very careful.
7.
Adjust the air inside the boot to normal as shown below.
Normal
Lack of air
Too much air

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Installation illustration

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Installation illustration

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Installation illustration


8.
Install the reduction gear side joint large diameter (A) and small diameter (B) boot band.

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Installation illustration

Information
Use the right tool for each type of boot band as shown in the table below.
Ear type
Hook type
Hook type
[Low profile]
SST (0K495 - C5000)
SST (09495 - 39100)
SST (0K495 - 2W001)

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Installation illustration

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Installation illustration

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Installation illustration


Note
•
Install in the following order : large diameter boot band (A) → small diameter boot band (B).
•
Installing in the wrong order can cause leaks.
•
When installing the boot band, align the fastened direction with the wheel side joint boot band.

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Installation illustration

•
Clean if there is any grease around the boot band after installing.
•
When installing the ear type boot band, check the clearance (A) as shown below.

Clearance (A) :
2.0 mm (0.0787 in.) or less.

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Installation illustration

•
When using the low profile hook type boot band, fit the SST tip (B) into the boot band hole (A) as shown below.

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Installation illustration

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Installation illustration

9.
Install the front driveshaft.
(Refer to Front Driveshaft Assembly (4WD) - "Front Driveshaft")

Joint Assembly (Reduction gear side) Inspection

Inspection
1.
Check spline (A) for damage / wear / crack.

Driveshaft and Axle — Front Driveshaft Assembly (4WD) / Joint Assembly (Reduction gear side) / Inspection illustration

2.
Check the boot for water or foreign objects.
3.
Check joint assembly for damage / wear / crack and rust.
4.
Replace any defective parts.

Other information:

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: V2L has ended. Battery level has reached the set value

V2L has ended. Battery level has reached the set value When the Kia EV6 high-voltage battery charge reaches the configured discharge limit, the V2L function automatically stops operating and a warning message appears on the instrument cluster. To continue using V2L, set the discharge limit lower than the current battery charge level.

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Parking Distance Warning (PDW): (if equipped)

The Kia EV6 Forward, Side, and Reverse Parking Distance Warning system uses ultrasonic sensors located around the vehicle to detect nearby people, animals, or objects while the vehicle is stationary or moving at low speed. This advanced Kia EV6 parking assistance technology helps improve parking precision and driver awareness in tight spaces, garages, and crowded urban environments.

Contents

Categories

 
Copyright © 2026 Kia EV6 Manuals ⏱ 0.0197