Kia EV6: Driveshaft and Axle / Rear Driveshaft & Axle Assembly

Contents:

Integrated Drive Axle (IDA) Troubleshooting

Troubleshooting
Note
Be careful not to misdiagnose a vehicle with brake and tailgate noise as an IDA defect.
Symptom
Suspected causes
Correction
Noises while braking
Bumping noises when braking
Thumping noise when braking after forward/reverse
Clicking, thumping noises when braking after shifting gear position (D↔R)
Cracking noise when braking after starting the vehicle
Abnormal brake caliper play
Corroded, scratched, damaged brake discs and pads
Brake creep groan noise
Adjust or replace
Noise from the rear of the vehicle while driving
Clunking, and knocking noises when driving on uneven road
Clicking, and creaking noises while accelerating or decelerating
Improper tailgate installation
Adjust or replace
IDA noise / vibration
Roaring noises and abnormal vibration while driving
Juddering when starting or accelerating (vibration)
Periodic crackling noise when driving (straight/turning)
1. Loosen disc mounting screws
Retighten
2. Loosen wheel bearings and knuckle/carrier bolts
Motor/reduction gear and joint assembly part circlip fastening faulty
Retighten
3. Motor / reduction gear and joint assembly part circlip fastening faulty
Joint inner shaft and inner joint assembly part circlip / snap ring fastening faulty
Retighten
4. Excessive wear, play, and damage on the joint assembly
Replacement
(Replacement using repair kit)
5. Bent or damaged shaft
6. Excessive wear, play, damage, or deterioration of the flange face of the wheel bearings
Leakage
Boot grease scattering or leakage
Improper installation of the boot or boot band

Integrated Drive Axle (IDA) Components and Components Location

Component

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Integrated Drive Axle (IDA) / Components and Components Location / Component illustration

1. Bearing Bracket and Shaft Assy [LH]
2. Housing (Reduction Gear Side)
3. Drive axle Boot Band
4. Drive axle Boot
5. Shaft Assembly
6. Snap Ring
7. Housing and Hub Bearing (Wheel Side)

Integrated Drive Axle (IDA) Removal and Installation

Removal
Warning
•
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
•
When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
1.
Disconnect the battery negative ( - ) terminal and the service interlock connector.
(Refer to Battery Control System - "Auxiliary 12 V Battery - 2WD")
(Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
2.
Remove the rear wheel and tires.
(Refer to Suspension System - "Wheel")
3.
Remove the rear under cover.
(Refer to Rear Motor and Reduction Gear System - "Rear Under Cover")
4.
Remove the rear brake disc.
(Refer to Brake System - "Rear Brake Disc")
5.
Separate the rear upper arm - front (A) after removing the bolt and nut.

Tightening torque :
156.9 - 176.5 N·m (16.0 - 18.0 kgf·m, 115.7 - 130.2 lb·ft)

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Integrated Drive Axle (IDA) / Removal and Installation / Removal illustration

Note
•
Install the transmission jack and lift up the parts to prevent the bolts and nuts from damage when installing or removing.
•
Be careful not to change the position of the bolt, nut, and washer when installing.
Information
Fix the bolt and remove or install the nut.
6.
Remove the Integrated Drive Axle (IDA) bolts (A).

Tightening torque :
127.5 - 147.1 N·m (13.0 - 15.0 kgf·m, 94.0 - 108.5 lb·ft)

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Integrated Drive Axle (IDA) / Removal and Installation / Removal illustration

7.
Remove the IDA.
Note
•
Do not pull the wheel side axle when removing IDA, damage to the inside of the reduction gear may occur, pull the joint cup (A).

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Integrated Drive Axle (IDA) / Removal and Installation / Removal illustration

•
When carrying IDA, hold the shaft or both side joints.
•
Do not insert the pry bar too deep, as this may damage the oil seal.
•
Removing the driveshaft using excessive force may damage the boot or bearing.
•
Plug the hole of the reduction gear case with the oil seal cap to prevent contamination.
•
Replace the retainer ring each time the drive shaft is removed.
[LH]
(1)
Remove the bearing bracket bolts (A).

Tightening torque :
63.7 - 70.6 N·m (6.5 - 7.2 kgf·m, 47 - 52.1 lb·ft)

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Integrated Drive Axle (IDA) / Removal and Installation / Removal illustration

(2)
Remove the LH IDA (A).

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Integrated Drive Axle (IDA) / Removal and Installation / Removal illustration

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Integrated Drive Axle (IDA) / Removal and Installation / Removal illustration

[RH]
(1)
Remove the RH IDA (A).

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Integrated Drive Axle (IDA) / Removal and Installation / Removal illustration

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Integrated Drive Axle (IDA) / Removal and Installation / Removal illustration

8.
Remove the bearing bracket and shaft assembly (A). [LH]

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Integrated Drive Axle (IDA) / Removal and Installation / Removal illustration

Installation
Warning
•
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
•
When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
1.
Install in the reverse order of removal.
Note
The existing inner shaft circlip should be replaced with new one (do not reuse).

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Integrated Drive Axle (IDA) / Removal and Installation / Installation illustration

Integrated Drive Axle (IDA) Inspection

Inspection
1.
Check brake disc for damage.
2.
Check the rear carrier for cracks.
3.
Check hub bearing for defects.

Joint Assembly (Wheel side) Removal

Removal
Note
•
Integrated Drive Axle (IDA) requires special grease, so do not add any other type of grease.
•
When replacing the boot band, it must be a new one.
1.
Remove the IDA.
(Refer to Rear Driveshaf & Axle Assembly - "Integrated Drive Axle (IDA)")
2.
Remove the wheel side large diameter boot band (A) using a flat-head screw driver.

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Wheel side) / Removal illustration

Information
Broaden the (A) using a flat-head screw driver and push the (B) to remove it.

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Wheel side) / Removal illustration

3.
Remove the wheel side small diameter boot band (A) using a flat-head screw driver.

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Wheel side) / Removal illustration

4.
Remove the boot (A) from the hub bearing.

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Wheel side) / Removal illustration

5.
Extend the snap ring (A) from side to side using a snap ring plier.

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Wheel side) / Removal illustration

Information
Clean the grease inside the hub bearing as much as possible using a clean cloth to locate the snap ring.
6.
Remove the hub bearing (A) while the snap ring is extended.

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Wheel side) / Removal illustration

7.
Remove the wheel side joint boot (A).

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Wheel side) / Removal illustration

Joint Assembly (Wheel side) Installation

Special Service Tool
Tool Name / Number
Illustration
Description
Band installer
0K495 - C5000

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Wheel side) / Installation / Special Service Tool illustration

Used for installing ear type boot band(Sharing handle with 0K495 - 2W000)

Installation
Note
•
When assembling, be careful not to let dust and foreign substances enter.
•
Integrated Drive Axle (IDA) requires special grease, so do not add any other type of grease.
•
Do not reuse the boot band.
1.
Install the boot (A), large diameter band (B), small diameter boot band (C).

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Wheel side) / Installation illustration

Note
Install the boot (A) last.
2.
Apply grease inside the hub bearing (A) and boot (B).

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Wheel side) / Installation illustration

Note
•
Use the only grease included in the joint kit/boot kit.
•
Use only half of the grease (150g) provided.

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Wheel side) / Installation illustration

•
Apply grease about 80% inside the bearing and about 20% inside the boot when replacing the whole part.
•
Apply grease about 20% inside the boot when replacing the boot.
•
Apply grease about 30% inside the bearing and 20% inside the boot If there is not enough grease inside the bearing.
•
Integrated Drive Axle (IDA) requires special grease, so do not add any other type of grease.
3.
Install the hub bearing (A).

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Wheel side) / Installation illustration

Note
•
When installing the hub bearing, make sure the spline (A) fits into the hub bearing correctly.
•
Make sure that the snap ring fits into the groove (B) securely.

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Wheel side) / Installation illustration

•
Do not reuse the snap ring.
•
After installation, move by hand to check that the hub bearing is securely installed.
4.
Install the boot (A) to the hub bearing.

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Wheel side) / Installation illustration

Note
Make sure the grooves (A), and (B) fit when installing.

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Wheel side) / Installation illustration

5.
Install the wheel side large diameter boot band.
(1)
Pre-Install the large diameter band (A).

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Wheel side) / Installation illustration

(2)
Using a tool such as a plier, tighten large diameter band (A) to install it.

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Wheel side) / Installation illustration

Note
•
Install in order of large diameter band → small diameter band to prevent leakage.
•
Make sure that the teeth (A) covered and the retainer cup (B) exposed after installing.
If the teeth are exposed and the retainer cup is not exposed after installing, the boot band may be dislodged and grease may leak. Reinstall the boot band.

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Wheel side) / Installation illustration

6.
Install the wheel side small diameter boot band (A) using the SST (0K495 - C5000).

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Wheel side) / Installation illustration

Note
•
Install in order of large diameter band → small diameter band to prevent leakage.
•
Check the gap (A) after installing.

Ear type boot band gap (A) :
2.0 mm (0.0787 in.) or less

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Wheel side) / Installation illustration

7.
Install the Integrated Drive Axle (IDA).
(Refer to Rear Driveshaf & Axle Assembly - "Integrated Drive Axle (IDA)")

Joint Assembly (Wheel side) Inspection

Inspection
1.
Check spline (A) for damage, wear and tear.

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Wheel side) / Inspection illustration

2.
Check the boot for water or foreign objects.
3.
Check joint assembly for damage, wear and tear.
4.
Check hub bearing for damage, wear and tear.

Joint Assembly (Reduction gear side) Removal

Removal
Note
•
Integrated Drive Axle (IDA) requires special grease, so do not add any other type of grease.
•
When replacing the boot band, it must be a new one.
1.
Remove the IDA.
(Refer to Rear Driveshaf & Axle Assembly - "Integrated Drive Axle (IDA)")
2.
Remove the reduction gear side large diameter boot band (A) using a flat-head screw driver.

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Reduction gear side) / Removal illustration

Information
Broaden the (A) using a flat-head screw driver and push the (B) to remove it.

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Reduction gear side) / Removal illustration

3.
Remove the reduction gear side small diameter boot band (A) using a flat-head screw driver.

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Reduction gear side) / Removal illustration

4.
Remove the boot (A) from the reduction gear side housing.

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Reduction gear side) / Removal illustration

5.
Extend the snap ring (A) from side to side using a snap ring plier.

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Reduction gear side) / Removal illustration

Information
Clean the grease inside the hub bearing as much as possible using a clean cloth to locate the snap ring.
6.
Remove the reduction gear side housing (A) while the snap ring is extended.

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Reduction gear side) / Removal illustration

Note
Do not reuse the snap ring.
7.
Remove reduction gear side boot (A).

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Reduction gear side) / Removal illustration

Joint Assembly (Reduction gear side) Installation

Special Service Tool
Tool Name / Number
Illustration
Description
Band installer
0K495 - C5000

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Reduction gear side) / Installation / Special Service Tool illustration

Used for installing ear type boot band(Sharing handle with 0K495 - 2W000)

Installation
Note
•
When assembling, be careful not to let dust and foreign substances enter.
•
Integrated Drive Axle (IDA) requires special grease, so do not add any other type of grease.
•
Do not reuse the boot band.
1.
Install the boot (A), large diameter band (B), small diameter boot band (C).

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Reduction gear side) / Installation illustration

Note
Install the boot (A) last.
2.
Apply grease inside the housing (A) and boot (B).

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Reduction gear side) / Installation illustration

Note
•
Use the only grease included in the joint kit/boot kit.
•
Use only half of the grease (150g) provided.

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Reduction gear side) / Installation illustration

•
Apply grease about 80% inside the housing and about 20% inside the boot when replacing the whole part.
•
Apply grease about 20% inside the boot when replacing the boot.
•
Apply grease about 30% inside the housing and 20% inside the boot If there is not enough grease inside the housing.
•
Integrated Drive Axle (IDA) requires special grease, so do not add any other type of grease.
3.
Install the reduction gear side housing (A).

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Reduction gear side) / Installation illustration

Note
•
When installing the hub bearing, make sure the spline (A) fits into the hub bearing correctly.
•
Make sure that the snap ring fits into the groove (B) securely.

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Reduction gear side) / Installation illustration

•
Do not reuse the snap ring.
•
After installation, move by hand to check that the reduction gear side housing is securely installed.
4.
Install the boot (A) to the reduction gear side housing.

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Reduction gear side) / Installation illustration

Note
Make sure the grooves (A), and (B) fit when installing.

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Reduction gear side) / Installation illustration

5.
Install the reduction gear side large diameter boot band.
(1)
Pre-Install the large diameter band (A).

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Reduction gear side) / Installation illustration

(2)
Using a tool such as a plier, tighten the (A) of the large diameter band to install it.

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Reduction gear side) / Installation illustration

Note
•
Install in order of large diameter band → small diameter band to prevent leakage.
•
Make sure that the teeth (A) covered and the retainer cup (B) exposed after installing.
If the teeth are exposed and the retainer cup is not exposed after installing, the boot band may be dislodged and grease may leak. Reinstall the boot band.

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Reduction gear side) / Installation illustration

6.
Install the wheel side small diameter boot band (A) using the SST (0K495 - C5000).

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Reduction gear side) / Installation illustration

Note
•
Install in order of large diameter band → small diameter band to prevent leakage.
•
Check the gap (A) after installing.

Ear type boot band gap (A) :
2.0 mm (0.0787 in.) or less

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Reduction gear side) / Installation illustration

7.
Install the Integrated Drive Axle (IDA).
(Refer to Rear Driveshaf & Axle Assembly - "Integrated Drive Axle (IDA)")

Joint Assembly (Reduction gear side) Inspection. Rear axle - carrier Components and Components Location

Joint Assembly (Reduction gear side) Inspection

Inspection
1.
Check spline (A) for damage, wear and tear.

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Joint Assembly (Reduction gear side) / Inspection illustration

2.
Check the boot for water or foreign objects.
3.
Check joint assembly for damage, wear and tear.
4.
Check hub bearing for damage, wear and tear.

Rear axle - carrier Components and Components Location

Component

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Rear axle - carrier / Components and Components Location / Component illustration

1. Rear Brake Disc
1-a. 4.9 - 5.9 N·m (0.5 - 0.6 kgf·m, 3.6 - 4.3 lb·ft)
2. Integrated Drive Axle (IDA)
2-a. 127.5 - 147.1 N·m (13.0 - 15.0 kgf·m, 94.0 - 108.5 lb·ft)
3. Rear Dust Cover

4. Rear Carrier
4-a. 156.9 - 176.5 N·m (16.0 - 18.0 kgf·m, 115.7 - 130.2 lb·ft)
4-b. 156.9 - 176.5 N·m (16.0 - 18.0 kgf·m, 115.7 - 130.2 lb·ft)
4-c. 98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)
4-d. 117.7 - 137.3 N·m (12.0 - 14.0 kgf·m, 86.8 - 101.3 lb·ft)
4-e. 176.5 - 196.1 N·m (18.0 - 20.0 kgf·m, 130.2 - 144.7 lb·ft)
4-f. 117.7 - 137.3 N·m (12.0 - 14.0 kgf·m, 86.8 - 101.3 lb·ft)

Rear axle - carrier Removal and Installation

Removal
Warning
•
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
•
When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
1.
Disconnect the battery negative ( - ) terminal and the service interlock connector.
(Refer to Battery Control System - "Auxiliary 12 V Battery - 2WD")
(Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
2.
Remove the rear wheel and tires.
(Refer to Suspension System - "Wheel")
3.
Remove the rear under cover.
(Refer to Rear Motor and Reduction Gear System - "Rear Under Cover")
4.
Remove the rear brake disc.
(Refer to Brake System - "Rear Brake Disc")
5.
Remove the rear wheel speed sensor (A) after removing the bolt.

Tightening torque :
8.8 - 13.7 N·m (0.9 - 1.4 kgf·m, 6.5 - 10.1 lb·ft)

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Rear axle - carrier / Removal and Installation / Removal illustration

6.
Separate the stabilizer bar link (A) after removing the nut.

Tightening torque :
98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Rear axle - carrier / Removal and Installation / Removal illustration

Note
Install the transmission jack and lift up the parts to prevent the bolts and nuts from damage when installing or removing.
7.
Separate the rear assist arm (A) after removing the the bolt, nut, and washer.

Tightening torque :
117.7 - 137.3 N·m (12.0 - 14.0 kgf·m, 86.8 - 101.3 lb·ft)

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Rear axle - carrier / Removal and Installation / Removal illustration

Note
•
Install the transmission jack and lift up the parts to prevent the bolts and nuts from damage when installing or removing.
•
Be careful not to change the position of the bolt, nut, and washer when installing.
Information
Fix the bolt and remove or install the nut.
8.
Separate the trailing arm (A) after removing the bolt and nut.

Tightening torque :
117.7 - 137.3 N·m (12.0 - 14.0 kgf·m, 86.8 - 101.3 lb·ft)

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Rear axle - carrier / Removal and Installation / Removal illustration

Note
•
Install the transmission jack and lift up the parts to prevent the bolts and nuts from damage when installing or removing.
•
Be careful not to change the position of the bolt, nut, and washer when installing.
Information
Fix the bolt and remove or install the nut.
9.
Separate the rear upper arm - front (A) after removing the bolt and nut.

Tightening torque :
156.9 - 176.5 N·m (16.0 - 18.0 kgf·m, 115.7 - 130.2 lb·ft)

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Rear axle - carrier / Removal and Installation / Removal illustration

Note
•
Install the transmission jack and lift up the parts to prevent the bolts and nuts from damage when installing or removing.
•
Be careful not to change the position of the bolt, nut, and washer when installing.
Information
Fix the bolt and remove or install the nut.
10.
Separate the rear upper arm - rear (A) after removing the bolt, nut, and washer.

Tightening torque :
156.9 - 176.5 N·m (16.0 - 18.0 kgf·m, 115.7 - 130.2 lb·ft)

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Rear axle - carrier / Removal and Installation / Removal illustration

Note
•
Install the transmission jack and lift up the parts to prevent the bolts and nuts from damage when installing or removing.
•
Be careful not to change the position of the bolt, nut, and washer when installing.
Information
Fix the bolt and remove or install the nut.
11.
Separate the rear lower arm (A) after removing the bolt, nut, and washer.

Tightening torque :
176.5 - 196.1 N·m (18.0 - 20.0 kgf·m, 130.2 - 144.7 lb·ft)

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Rear axle - carrier / Removal and Installation / Removal illustration

Note
•
Install the transmission jack and lift up the parts to prevent the bolts and nuts from damage when installing or removing.
•
Be careful not to change the position of the bolt, nut, and washer when installing.
Information
Fix the bolt and remove or install the nut.
12.
Remove the inner shaft bearing bracket bolts (A). [LH]

Tightening torque :
63.7 - 70.6 N·m (6.5 - 7.2 kgf·m, 47 - 52.1 lb·ft)

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Rear axle - carrier / Removal and Installation / Removal illustration

13.
Remove the rear carrier and Integrated Drive Axle (IDA) (A).

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Rear axle - carrier / Removal and Installation / Removal illustration

Note
•
Do not pull the wheel side axle when removing IDA, damage to the inside of the reduction gear may occur, pull the joint cup (A).

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Rear axle - carrier / Removal and Installation / Removal illustration

•
When carrying IDA, hold the shaft or both side joints.
•
Do not insert the pry bar too deep, as this may damage the oil seal.
•
Removing the driveshaft using excessive force may damage the boot or bearing.
•
Plug the hole of the reduction gear case with the oil seal cap to prevent contamination.
•
Replace the retainer ring each time the drive shaft is removed.
14.
Remove the rear stabilizer bar link (A) after removing the nut.

Tightening torque :
98.1 - 117.7 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.8 lb·ft)

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Rear axle - carrier / Removal and Installation / Removal illustration

15.
Remove the IDA mounting bolts (A).

Tightening torque :
127.5 - 147.1 N·m (13.0 - 15.0 kgf·m, 94.0 - 108.5 lb·ft)

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Rear axle - carrier / Removal and Installation / Removal illustration

16.
Remove the IDA and rear dust cover (A).

Driveshaft and Axle — Rear Driveshaft & Axle Assembly / Rear axle - carrier / Removal and Installation / Removal illustration

Installation
Warning
•
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
•
When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
1.
Install in the reverse order of removal.
2.
Check the alignment.
(Refer to Suspension System - "Alignment")

Rear axle - carrier Inspection

Inspection
1.
Check the rear carrier for cracks.

Other information:

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: General Safety Information and Caution

Precaution (R-134a) When Handling Refrigerant 1. R-134a liquid refrigerant is highly volatile. A drop on the skin of your hand could result in localized frostbite. When handling the refrigerant, be sure to wear gloves. 2. It is standard practice to wear goggles or glasses to protect your eyes, and gloves to protect your hands.

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Blind-spot View Monitor (BVM): (if equipped)

Figure 1. Left Figure 2. Right The Kia EV6 Blind-Spot View Monitor (BVM) system displays a live video view of the rear blind spot area on the instrument cluster whenever the turn signal is activated. The Kia EV6 Blind-Spot View Monitor system helps improve visibility during lane changes and assists the driver in monitoring surrounding traffic conditions more safely.

 
Copyright © 2026 Kia EV6 Manuals ⏱ 0.0254