Kia EV6: Cooling System / High Voltage Battery Cooling System

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual / Cooling System / High Voltage Battery Cooling System

Contents:

High Voltage Battery Coolant Drain

Special Service Tool
Tool Name / Number
Illustration
Description
Coolant refiller & suction tool
0K253 - J2300

Cooling System — High Voltage Battery Cooling System / High Voltage Battery Coolant / Drain / Special Service Tool illustration

Used to drain and fill the coolant for EV
Cap adapter
0K253 - J2320

Cooling System — High Voltage Battery Cooling System / High Voltage Battery Coolant / Drain / Special Service Tool illustration

Used to drain and fill the coolant for EV

SST (0K253 - J2300) Detail Name

Cooling System — High Voltage Battery Cooling System / High Voltage Battery Coolant / Drain / Special Service Tool illustration

Cooling System — High Voltage Battery Cooling System / High Voltage Battery Coolant / Drain / Special Service Tool illustration

1. Pressure Valve
2. Suction Valve
3. Vacuum Valve 1
4. Vacuum Valve 2
5. Coolant Injection
6. Vacuum Valve
7. Regulator Pressure Gauge
8. Pressure Gauge
9. Vacuum Gauge
10. Air Pressurization Valve
11. Vacuum Outlet Valve
12. Air Hose Inlet Valve
13. Regulator Adjusting Knob

Drain
Warning
•
When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
•
When working a high voltage system, the technician must be recognized and observe "General Safety Information and Caution". If do not follow, serious accidents like electric shock and short circuit are caused.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Disconnect the battery negative ( - ) terminal and the high voltage service interlock connector.
(Refer to Battery Control System - "Auxiliary Battery (12 V)")
(Refer to Battery Control System - "Auxiliary Battery (12 V)" -4WD)
2.
Open the reservoir tank cap (A).

Cooling System — High Voltage Battery Cooling System / High Voltage Battery Coolant / Drain illustration

3.
Install the cap adapter (0K253 - J2320).

Cooling System — High Voltage Battery Cooling System / High Voltage Battery Coolant / Drain illustration

4.
Install the radiator cap connection hose (A) to the radiator cap adapter (B).

Cooling System — High Voltage Battery Cooling System / High Voltage Battery Coolant / Drain illustration

5.
Connect the radiator cap connection hose (A) to the air pressurization valve of SST (0K253 - J2300).

Cooling System — High Voltage Battery Cooling System / High Voltage Battery Coolant / Drain illustration

6.
Install the air hose (A) to the air inlet valve of SST (0K253 - J2300).

Cooling System — High Voltage Battery Cooling System / High Voltage Battery Coolant / Drain illustration

Note
Make sure all valves are closed.

Cooling System — High Voltage Battery Cooling System / High Voltage Battery Coolant / Drain illustration

7.
Turn the regulator adjusting knob (A) to set pressure gauge (B) to 0.2 Mpa.

Cooling System — High Voltage Battery Cooling System / High Voltage Battery Coolant / Drain illustration

Note
After adjusting the pressure, close the regulator adjustment knob.
8.
Remove the front under cover.
(Refer to Motor & Reduction Gear System - "Front Under Cover")
9.
Release the quick connector, and then disconnect the high voltage battery EWP cooling hose (A).
[2WD]

Cooling System — High Voltage Battery Cooling System / High Voltage Battery Coolant / Drain illustration

[4WD]

Cooling System — High Voltage Battery Cooling System / High Voltage Battery Coolant / Drain illustration

10.
Install the coolant drain adapter and hose (A) to the battery EWP and EWP cooling hose.
[2WD]

Cooling System — High Voltage Battery Cooling System / High Voltage Battery Coolant / Drain illustration

[4WD]

Cooling System — High Voltage Battery Cooling System / High Voltage Battery Coolant / Drain illustration

11.
Put the opposite of the coolant drain adapter and hose (A) to a bucket (B).

Cooling System — High Voltage Battery Cooling System / High Voltage Battery Coolant / Drain illustration

12.
Turn the pressure valve (A) the direction of the arrow to drain coolant.

Cooling System — High Voltage Battery Cooling System / High Voltage Battery Coolant / Drain illustration

Note
Make sure that the valves other than the pressure valve (A) are closed.
13.
Close the pressure valve after draining coolant, and then install the high voltage battery EWP coolant hose (A).
[2WD]

Cooling System — High Voltage Battery Cooling System / High Voltage Battery Coolant / Drain illustration

[4WD]

Cooling System — High Voltage Battery Cooling System / High Voltage Battery Coolant / Drain illustration

14.
Separate the radiator cap connection hose (A) to the air pressurization valve.

Cooling System — High Voltage Battery Cooling System / High Voltage Battery Coolant / Drain illustration

High Voltage Battery Coolant Refilling

Special Service Tool
Tool Name / Number
Illustration
Description
Coolant refiller & suction tool
0K253 - J2300

Cooling System — High Voltage Battery Cooling System / High Voltage Battery Coolant / Refilling / Special Service Tool illustration

Used to drain and fill the coolant for EV
Cap adapter
0K253 - J2320

Cooling System — High Voltage Battery Cooling System / High Voltage Battery Coolant / Refilling / Special Service Tool illustration

Used to drain and fill the coolant for EV

SST (0K253 - J2300) Detail Name

Cooling System — High Voltage Battery Cooling System / High Voltage Battery Coolant / Refilling / Special Service Tool illustration

Cooling System — High Voltage Battery Cooling System / High Voltage Battery Coolant / Refilling / Special Service Tool illustration

1. Pressure Valve
2. Suction Valve
3. Vacuum Valve 1
4. Vacuum Valve 2
5. Coolant Injection
6. Vacuum Valve
7. Regulator Pressure Gauge
8. Pressure Gauge
9. Vacuum Gauge
10. Air Pressurization Valve
11. Vacuum Outlet Valve
12. Air Hose Inlet Valve
13. Regulator Adjusting Knob

Refilling
Note
•
Be careful not to spill coolant on the electric devices when replacing the coolant.
•
Use genuine antifreeze/coolant.
•
To prevent corrosion, the concentration of coolant should be maintained at a minimum of 45%. If the coolant concentration is less than 45%, there may be a risk of corrosion or freezing.
•
It is not recommended if the concentration of the coolant exceeds 60%, as the cooling effect may be reduced.
•
Do not mix antifreeze/coolant from different brands.
•
Do not add any anti-rust.
1.
Drain the high voltage battery coolant.
(Refer to High Voltage Battery Coolant - "Drain")
2.
Connect the radiator cap connection hose (A) to the vacuum valve of SST (0K253 - J2300).

Cooling System — High Voltage Battery Cooling System / High Voltage Battery Coolant / Refilling illustration

3.
Open the vacuum valve (A) in the direction of the arrow, and then close when the vacuum gauge (B) reaches the green area (C).

Cooling System — High Voltage Battery Cooling System / High Voltage Battery Coolant / Refilling illustration

Note
Make sure that the valves other than the vacuum valve (A) are closed.
4.
Connect the coolant suction hose (A) to SST (0K253 - J2300) coolant filler valve and place the opposite hose in the bucket (B) containing new coolant.

Cooling System — High Voltage Battery Cooling System / High Voltage Battery Coolant / Refilling illustration

5.
Turn the suction valve (A) in the direction of the arrow to fill new coolant, and then close it when the vacuum gauge reaches to '0'.

Cooling System — High Voltage Battery Cooling System / High Voltage Battery Coolant / Refilling illustration

Note
Check that the valve except the suction valve (A) is locked.
6.
Remove the cap adapter (0K253 - J2320).

Cooling System — High Voltage Battery Cooling System / High Voltage Battery Coolant / Refilling illustration

7.
Perform the order below with the KDS.
(Actuation Test → Vehicle Control → Battery EWP Operation Mode for Degassing and Circulation)
Note
Charge the auxiliary 12 V battery during performing "Battery Electric Water Pump Control" to prevent battery drain.
Information
When driving EWP, operate within 10 minutes.
8.
When the battery EWP operates and coolant circulates, refill coolant so that the coolant level is kept between "MAX" and "MIN" level.

Cooling System — High Voltage Battery Cooling System / High Voltage Battery Coolant / Refilling illustration

Note
Friction may damage the bearing if the EWP is operated without coolant.
9.
When the operational sound volume of the EWP becomes small and when no air bubbles can be seen in the reservoir tank, bleeding of the coolant system is completed.
Note
•
After air bleeding is completed make sure that coolant in the reservoir tank flow without air bubble during the EWP actuation.
•
If the coolant flow is not seen or air bubbles are still seen, repeat steps 7 to 8.
10.
After air bleeding is completed, refill the coolant to the MAX level and install the reservoir cap.

Cooling System — High Voltage Battery Cooling System / High Voltage Battery Coolant / Refilling illustration

11.
Check the coolant for leakage.
Note
The cooling system air bleeding and coolant injection are performed perfectly when the coolant is completely cooled. Check the coolant level of the reservoir tank for 2 - 3 days after flushing the coolant.
12.
Install the front under cover.
(Refer to Motor & Reduction Gear System - "Front Under Cover")

Coolant Distribution Pipe Components and Components Location

Component and Component Location
2WD

Cooling System — High Voltage Battery Cooling System / Coolant Distribution Pipe / Components and Components Location / Component and Component Location illustration

1. Distribution Pipe Cooling Hose
2. Distribution Pipe Cooling Hose
3. Distribution Pipe Cooling Hose
4. Coolant Distribution Pipe
4-a. 19.6 - 23.5 N·m (2.0 - 2.4 kgf·m, 14.5 - 17.4 lb·ft)

4WD

Cooling System — High Voltage Battery Cooling System / Coolant Distribution Pipe / Components and Components Location / Component and Component Location illustration

1. Distribution Pipe Cooling Hose
2. Distribution Pipe Cooling Hose
3. Distribution Pipe Cooling Hose
4. Coolant Distribution Pipe
4-a. 19.6 - 23.5 N·m (2.0 - 2.4 kgf·m, 14.5 - 17.4 lb·ft)

Coolant Distribution Pipe Removal and Installation - 2WD

Removal
Warning
•
When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
•
When working a high voltage system, the technician must be recognized and observe "General Safety Information and Caution". If do not follow, serious accidents like electric shock and short circuit are caused.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Note
When disconnecting a quick connector, refer to the following according to the type of quick connector.
[Type A]
- Remove while pressing the quick connector clamp (A) in the direction of the arrow.

Cooling System — High Voltage Battery Cooling System / Coolant Distribution Pipe / Removal and Installation - 2WD / Removal illustration

- Do not touch the rubber seal (A) inside the hose.

Cooling System — High Voltage Battery Cooling System / Coolant Distribution Pipe / Removal and Installation - 2WD / Removal illustration

[Type B]
- Pull the quick connector clamp (A) in the direction of the arrow to separate the clamp and remove the hose.

Cooling System — High Voltage Battery Cooling System / Coolant Distribution Pipe / Removal and Installation - 2WD / Removal illustration

- Do not touch the rubber seal (A) inside the hose.

Cooling System — High Voltage Battery Cooling System / Coolant Distribution Pipe / Removal and Installation - 2WD / Removal illustration

1.
Drain the high voltage battery coolant.
(Refer to High Voltage Battery Coolant - "Drain")
2.
Disconnect the coolant distribution pipe cooling hose (A) by releasing the quick connector.

Cooling System — High Voltage Battery Cooling System / Coolant Distribution Pipe / Removal and Installation - 2WD / Removal illustration

3.
Disconnect the coolant distribution pipe cooling hoses (A, B, C) after releasing the quick connectors.

Cooling System — High Voltage Battery Cooling System / Coolant Distribution Pipe / Removal and Installation - 2WD / Removal illustration

4.
Disconnect the coolant distribution pipe cooling hose (A) by releasing the quick connector.

Cooling System — High Voltage Battery Cooling System / Coolant Distribution Pipe / Removal and Installation - 2WD / Removal illustration

5.
Remove the discharge hose (A) after removing the nut.

Tightening torque :
8.8 - 13.7 N·m (0.9 - 1.4 kgf·m, 6.5 - 10.1 lb·ft)

Cooling System — High Voltage Battery Cooling System / Coolant Distribution Pipe / Removal and Installation - 2WD / Removal illustration

6.
Remove the coolant distribution pipe (A) after removing the bolts.

Tightening torque :
19.6 - 23.5 N·m (2.0 - 2.4 kgf·m, 14.5 - 17.4 lb·ft)

Cooling System — High Voltage Battery Cooling System / Coolant Distribution Pipe / Removal and Installation - 2WD / Removal illustration

Installation
Warning
•
When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
•
When working a high voltage system, the technician must be recognized and observe "General Safety Information and Caution". If do not follow, serious accidents like electric shock and short circuit are caused.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.
2.
Perform the air bleeding procedures using the KDS after refilling the coolant.
(Refer to High Voltage Battery Coolant - "Refilling")
Note
Perform "Battery EWP Operation Mode for Degassing and Circulation" to air bleeding using KDS when filling with coolant.

Coolant Distribution Pipe Removal and Installation - 4WD

Removal
Warning
•
When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
•
When working a high voltage system, the technician must be recognized and observe "General Safety Information and Caution". If do not follow, serious accidents like electric shock and short circuit are caused.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Note
When disconnecting a quick connector, refer to the following according to the type of quick connector.
[Type A]
- Remove while pressing the quick connector clamp (A) in the direction of the arrow.

Cooling System — High Voltage Battery Cooling System / Coolant Distribution Pipe / Removal and Installation - 4WD / Removal illustration

- Do not touch the rubber seal (A) inside the hose.

Cooling System — High Voltage Battery Cooling System / Coolant Distribution Pipe / Removal and Installation - 4WD / Removal illustration

[Type B]
- Pull the quick connector clamp (A) in the direction of the arrow to separate the clamp and remove the hose.

Cooling System — High Voltage Battery Cooling System / Coolant Distribution Pipe / Removal and Installation - 4WD / Removal illustration

- Do not touch the rubber seal (A) inside the hose.

Cooling System — High Voltage Battery Cooling System / Coolant Distribution Pipe / Removal and Installation - 4WD / Removal illustration

1.
Drain the high voltage battery coolant.
(Refer to High Voltage Battery Coolant - "Drain")
2.
Remove the front trunk.
(Refer to Body - "Front Trunk")
3.
Disconnect the coolant distribution pipe cooling hose (A) by releasing the quick connector.

Cooling System — High Voltage Battery Cooling System / Coolant Distribution Pipe / Removal and Installation - 4WD / Removal illustration

4.
Disconnect the coolant distribution pipe cooling hoses (A) by releasing the quick connectors.

Cooling System — High Voltage Battery Cooling System / Coolant Distribution Pipe / Removal and Installation - 4WD / Removal illustration

Cooling System — High Voltage Battery Cooling System / Coolant Distribution Pipe / Removal and Installation - 4WD / Removal illustration

5.
Disconnect the coolant distribution pipe cooling hose (A) by releasing the quick connector.

Cooling System — High Voltage Battery Cooling System / Coolant Distribution Pipe / Removal and Installation - 4WD / Removal illustration

6.
Disconnect the coolant distribution pipe cooling hose (B) by releasing the quick connector after disconnecting the coolant temperature sensor (A).

Cooling System — High Voltage Battery Cooling System / Coolant Distribution Pipe / Removal and Installation - 4WD / Removal illustration

7.
Separate the motor and reduction gear oil cooler hose (A).

Cooling System — High Voltage Battery Cooling System / Coolant Distribution Pipe / Removal and Installation - 4WD / Removal illustration

8.
Remove the coolant distribution pipe (A) after removing the bolt and nut.

Tightening torque :
16.7 - 23.5 N·m (2.0 - 2.4 kgf·m, 14.5 - 17.3 lb·ft)

Cooling System — High Voltage Battery Cooling System / Coolant Distribution Pipe / Removal and Installation - 4WD / Removal illustration

Installation
Warning
•
When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
•
When working a high voltage system, the technician must be recognized and observe "General Safety Information and Caution". If do not follow, serious accidents like electric shock and short circuit are caused.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.
2.
Perform the air bleeding procedures using the KDS after refilling the coolant.
(Refer to High Voltage Battery Coolant - "Refilling")
Note
Perform "Battery EWP Operation Mode for Degassing and Circulation" to air bleeding using KDS when filling with coolant.

Battery Heater Specification. Battery Heater Components and Components Location

Battery Heater Specification

Specification
Item
Specification
Standard
Long range
Rated voltage (V)
DC 523
DC 697
Input voltage (V)
DC 360 - 619
DC 480 - 826
Heater capacity (kW)
4.04
4.6
Ampere (A)
Maximum 9.1
Maximum 7.8
Heater resistance (Ω)
64.3 - 71.1
100.3 - 110.9
Operating temperature [°C (°F)]
-40 to 105 (-40 to 221)
-40 to 105 (-40 to 221)

Battery Heater Components and Components Location

Component and Component Location
2WD

Cooling System — High Voltage Battery Cooling System / Battery Heater / Components and Components Location / Component and Component Location illustration

1. Battery Heater Coolant Hose
2. Battery Heater Coolant Hose
3. Battery Heater
3-a. 6.9 - 9.8 N·m (0.7 - 1.0 kgf·m, 5.1 - 7.2 lb·ft)

4WD

Cooling System — High Voltage Battery Cooling System / Battery Heater / Components and Components Location / Component and Component Location illustration

1. Battery Heater Coolant Hose
2. Battery Heater Coolant Hose
3. Battery Heater
3-a. 6.9 - 9.8 N·m (0.7 - 1.0 kgf·m, 5.1 - 7.2 lb·ft)
3-b. 6.9 - 9.8 N·m (0.7 - 1.0 kgf·m, 5.1 - 7.2 lb·ft)

Battery Heater On Vehicle Inspection

Inspection
1.
The cooling system can be more quickly diagnosed for problems using the KDS (Refer to "DTC guide").
(1)
Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) using the KDS
(Refer to DTC guide when fault code is found.)
Information
Refer to the KDS screen for operating conditions and details

Battery Heater Removal and Installation - 2WD

Removal
Warning
•
When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
•
When working a high voltage system, the technician must be recognized and observe "General Safety Information and Caution". If do not follow, serious accidents like electric shock and short circuit are caused.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Note
Follow the instructions below when releasing the quick connector.
- Remove while pressing the quick connector clamp (A) in the direction of the arrow.

Cooling System — High Voltage Battery Cooling System / Battery Heater / Removal and Installation - 2WD / Removal illustration

- Do not touch the rubber seal (A) inside the hose.

Cooling System — High Voltage Battery Cooling System / Battery Heater / Removal and Installation - 2WD / Removal illustration

1.
Perform the high voltage shut off procedure.
(Refer to Cooling System - "High Voltage Shut-off Procedures")
2.
Drain the high voltage battery coolant.
(Refer to High Voltage Battery Coolant - "Drain")
3.
Remove the front trunk.
(Refer to Body - "Front Trunk")
4.
Disconnect the battery heater connector (A).

Cooling System — High Voltage Battery Cooling System / Battery Heater / Removal and Installation - 2WD / Removal illustration

5.
Disconnect the battery heater coolant hose (A) after releasing the quick connector.

Cooling System — High Voltage Battery Cooling System / Battery Heater / Removal and Installation - 2WD / Removal illustration

6.
Separate the battery heater ground cable (A) after removing the bolt.

Tightening torque :
6.9 - 9.8 N·m (0.7 - 1.0 kgf·m, 5.1 - 7.2 lb·ft)

Cooling System — High Voltage Battery Cooling System / Battery Heater / Removal and Installation - 2WD / Removal illustration

7.
Disconnect the battery heater coolant hose (A) after releasing the quick connector.

Cooling System — High Voltage Battery Cooling System / Battery Heater / Removal and Installation - 2WD / Removal illustration

8.
Disconnect the battery heater high voltage connector (A).

Cooling System — High Voltage Battery Cooling System / Battery Heater / Removal and Installation - 2WD / Removal illustration

9.
Separate the battery heater high voltage connector (A).

Cooling System — High Voltage Battery Cooling System / Battery Heater / Removal and Installation - 2WD / Removal illustration

10.
Remove the battery heater (A) after removing the bolts.

Tightening torque :
6.9 - 9.8 N·m (0.7 - 1.0 kgf·m, 5.1 - 7.2 lb·ft)

Cooling System — High Voltage Battery Cooling System / Battery Heater / Removal and Installation - 2WD / Removal illustration

Installation
Warning
•
When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
•
When working a high voltage system, the technician must be recognized and observe "General Safety Information and Caution". If do not follow, serious accidents like electric shock and short circuit are caused.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.
2.
Perform the air bleeding procedures using the KDS after refilling the coolant.
(Refer to High Voltage Battery Coolant - "Refilling")
Note
Perform "Battery EWP Operation Mode for Degassing and Circulation" to air bleeding using KDS when filling with coolant.

Battery Heater Removal and Installation - 4WD

Removal
Warning
•
When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
•
When working a high voltage system, the technician must be recognized and observe "General Safety Information and Caution". If do not follow, serious accidents like electric shock and short circuit are caused.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Note
Follow the instructions below when releasing the quick connector.
- Remove while pressing the quick connector clamp (A) in the direction of the arrow.

Cooling System — High Voltage Battery Cooling System / Battery Heater / Removal and Installation - 4WD / Removal illustration

- Do not touch the rubber seal (A) inside the hose.

Cooling System — High Voltage Battery Cooling System / Battery Heater / Removal and Installation - 4WD / Removal illustration

1.
Perform the high voltage shut off procedure.
(Refer to Cooling System - "High Voltage Shut-off Procedures")
2.
Drain the high voltage battery coolant.
(Refer to High Voltage Battery Coolant - "Drain")
3.
Remove the front trunk.
(Refer to Body - "Front Trunk")
4.
Disconnect the battery heater high voltage connector (A) and wiring clip (B).

Cooling System — High Voltage Battery Cooling System / Battery Heater / Removal and Installation - 4WD / Removal illustration

5.
Disconnect the battery heater coolant hose (A) after releasing the quick connector.

Cooling System — High Voltage Battery Cooling System / Battery Heater / Removal and Installation - 4WD / Removal illustration

6.
Separate the battery heater ground cable (A) after removing the bolt.

Tightening torque :
6.9 - 9.8 N·m (0.7 - 1.0 kgf·m, 5.1 - 7.2 lb·ft)

Cooling System — High Voltage Battery Cooling System / Battery Heater / Removal and Installation - 4WD / Removal illustration

7.
Disconnect the battery heater coolant hose (A) after releasing the quick connector.

Cooling System — High Voltage Battery Cooling System / Battery Heater / Removal and Installation - 4WD / Removal illustration

8.
Disconnect the battery heater connector (A) and wiring clip (B).

Cooling System — High Voltage Battery Cooling System / Battery Heater / Removal and Installation - 4WD / Removal illustration

9.
Remove the battery heater (A) after removing the bolts and nut.

Tightening torque :
6.9 - 9.8 N·m (0.7 - 1.0 kgf·m, 5.1 - 7.2 lb·ft)

Cooling System — High Voltage Battery Cooling System / Battery Heater / Removal and Installation - 4WD / Removal illustration

Installation
Warning
•
When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
•
When working a high voltage system, the technician must be recognized and observe "General Safety Information and Caution". If do not follow, serious accidents like electric shock and short circuit are caused.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.
2.
Perform the air bleeding procedures using the KDS after refilling the coolant.
(Refer to High Voltage Battery Coolant - "Refilling")
Note
Perform "Battery EWP Operation Mode for Degassing and Circulation" to air bleeding using KDS when filling with coolant.

3 Way Valve Specification. 3 Way Valve Components and Components Location

3 Way Valve Specification

Specification
Item
Specification
Operation voltage (V)
9 - 16
Rated current (A)
Maximum 1.3
Operating temperature [°C (°F)]
-40 to 115 (-40 to 239)

3 Way Valve Components and Components Location

Component and Component Location
2WD

Cooling System — High Voltage Battery Cooling System / 3 Way Valve / Components and Components Location / Component and Component Location illustration

1. 3-Way Valve Cooling Hose
2. 3-Way Valve Cooling Hose
3. 3-Way Valve Cooling Hose
4. 3-Way Valve
4-a. 19.6 - 23.5 N·m (2.0 - 2.4 kgf·m, 14.5 - 17.4 lb·ft)
5. 3-Way Valve Hose
6. 3-Way Valve Hose
7. Coolant 3-Way Valve
7-a. 7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)

4WD

Cooling System — High Voltage Battery Cooling System / 3 Way Valve / Components and Components Location / Component and Component Location illustration

1. 3-Way Valve Inlet Hose
2. 3-Way Valve Outlet Hose
3. 3-Way Valve Outlet Hose
4. 3-Way Valve
4-a. 19.6 - 23.5 N·m (2.0 - 2.4 kgf·m, 14.5 - 17.4 lb·ft)
5. 3-Way Valve Hose
6. 3-Way Valve Hose
7. Coolant 3-Way Valve
7-a. 7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)

3 Way Valve Removal and Installation - 2WD

Removal
Warning
•
When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
•
When working a high voltage system, the technician must be recognized and observe "General Safety Information and Caution". If do not follow, serious accidents like electric shock and short circuit are caused.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Note
Follow the instructions below when releasing the quick connector.
- Remove while pressing the quick connector clamp (A) in the direction of the arrow.

Cooling System — High Voltage Battery Cooling System / 3 Way Valve / Removal and Installation - 2WD / Removal illustration

- Do not touch the rubber seal (A) inside the hose.

Cooling System — High Voltage Battery Cooling System / 3 Way Valve / Removal and Installation - 2WD / Removal illustration

1.
Drain the high voltage battery coolant.
(Refer to High Voltage Battery Coolant - "Drain")
2.
Disconnect the 3 way valve cooling hoses (A, B, C) by releasing the quick connectors.

Cooling System — High Voltage Battery Cooling System / 3 Way Valve / Removal and Installation - 2WD / Removal illustration

3.
Disconnect the 3-way valve connector (A).

Cooling System — High Voltage Battery Cooling System / 3 Way Valve / Removal and Installation - 2WD / Removal illustration

4.
Remove the 3-way valve (A) after removing the bolts.

Tightening torque :
16.7 - 23.5 N·m (2.0 - 2.4 kgf·m, 14.5 - 17.3 lb·ft)

Cooling System — High Voltage Battery Cooling System / 3 Way Valve / Removal and Installation - 2WD / Removal illustration

Installation
Warning
•
When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
•
When working a high voltage system, the technician must be recognized and observe "General Safety Information and Caution". If do not follow, serious accidents like electric shock and short circuit are caused.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.
2.
Perform the air bleeding procedures using the KDS after refilling the coolant.
(Refer to High Voltage Battery Coolant - "Refilling")
Note
Perform "Battery EWP Operation Mode for Degassing and Circulation" to air bleeding using KDS when filling with coolant.

3 Way Valve Removal and Installation - 4WD

Removal
Warning
•
When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
•
When working a high voltage system, the technician must be recognized and observe "General Safety Information and Caution". If do not follow, serious accidents like electric shock and short circuit are caused.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Note
Follow the instructions below when releasing the quick connector.
- Remove while pressing the quick connector clamp (A) in the direction of the arrow.

Cooling System — High Voltage Battery Cooling System / 3 Way Valve / Removal and Installation - 4WD / Removal illustration

- Do not touch the rubber seal (A) inside the hose.

Cooling System — High Voltage Battery Cooling System / 3 Way Valve / Removal and Installation - 4WD / Removal illustration

1.
Drain the high voltage battery coolant.
(Refer to High Voltage Battery Coolant - "Drain")
2.
Remove the front trunk.
(Refer to Body - "Front Trunk")
3.
Disconnect the 3-way valve cooling hose (A) after releasing the quick connector.

Cooling System — High Voltage Battery Cooling System / 3 Way Valve / Removal and Installation - 4WD / Removal illustration

4.
Disconnect the 3-way valve cooling hoses (A) after releasing the quick connectors.

Cooling System — High Voltage Battery Cooling System / 3 Way Valve / Removal and Installation - 4WD / Removal illustration

5.
Disconnect the 3-way valve connector (A).

Cooling System — High Voltage Battery Cooling System / 3 Way Valve / Removal and Installation - 4WD / Removal illustration

6.
Remove the 3-way valve (A) after removing the bolts.

Tightening torque :
16.7 - 23.5 N·m (2.0 - 2.4 kgf·m, 14.5 - 17.3 lb·ft)

Cooling System — High Voltage Battery Cooling System / 3 Way Valve / Removal and Installation - 4WD / Removal illustration

Installation
Warning
•
When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
•
When working a high voltage system, the technician must be recognized and observe "General Safety Information and Caution". If do not follow, serious accidents like electric shock and short circuit are caused.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.
2.
Perform the air bleeding procedures using the KDS after refilling the coolant.
(Refer to High Voltage Battery Coolant - "Refilling")
Note
Perform "Battery EWP Operation Mode for Degassing and Circulation" to air bleeding using KDS when filling with coolant.

Electric Water Pump (EWP) Specification

Specification
Item
Specification
Operation voltage (V)
9 - 16
Rated current (A)
Maximum 6.5
Operating temperature [°C (°F)]
-40 to 135 (-40 to 275)

Electric Water Pump (EWP) Components and Components Location

Component and Component Location
Note
When checking the sensor data in KDS, the numbering of EWP will be different between Parts catalog and KDS data.
Part Number (Part Name)
Location
Mark Number
KDS
Workshop Manual
375W5-CV000
(WATER PUMP ASSY-ELECTRIC NO.1)
In front of the reservoir
EWP#2
EWP1
375V5-GI000,GI200
(WATER PUMP ASSY-ELECTRIC NO.2)
The underside of the vehicle
(Behind the motor)
EWP#1
EWP2

[2WD]

Cooling System — High Voltage Battery Cooling System / Electric Water Pump (EWP) / Components and Components Location / Component and Component Location illustration

1. Battery Electric Water Pump (EWP) 1
1-a. 2.0 - 2.5 N·m (0.20 - 0.25 kgf·m, 1.4 - 1.8 lb·ft, 17.4 - 21.7 lb·in)
2. Motor Electric Water Pump (EWP)
2-a. 2.0 - 2.5 N·m (0.20 - 0.25 kgf·m, 1.4 - 1.8 lb·ft, 17.4 - 21.7 lb·in)
3. Reservoir Tank Bracket
3-a. 7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)
4. Reservoir Tank
5. Electric Water Pump Hose
6. Coolant Distribution Pipe
7. Battery Electric Water Pump (EWP) 2
7-a. 6.9 - 9.8 N·m (0.7 - 1 kgf·m, 5.1 - 7.2 lb·ft)

[4WD]

Cooling System — High Voltage Battery Cooling System / Electric Water Pump (EWP) / Components and Components Location / Component and Component Location illustration

1. Battery Electric Water Pump (EWP) 1
1-a. 2.0 - 2.5 N·m (0.20 - 0.25 kgf·m, 1.4 - 1.8 lb·ft, 17.4 - 21.7 lb·in)
2. Motor Electric Water Pump (EWP)
2-a. 2.0 - 2.5 N·m (0.20 - 0.25 kgf·m, 1.4 - 1.8 lb·ft, 17.4 - 21.7 lb·in)
3. Reservoir Tank Bracket
3-a. 7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)
4. Reservoir Tank
5. Distribution Pipe
6. Electric Water Pump Hose
7. Battery Electric Water Pump (EWP) 2 Bracket
8. Battery Electric Water Pump (EWP) 2
8-a. 6.9 - 9.8 N·m (0.7 - 1.0 kgf·m, 5.1 - 7.2 lb·ft)
9. Battery Electric Water Pump (EWP) 2 Bracket
9-a. 19.6 - 23.5 N·m (2.0 - 2.4 kgf·m, 14.5 - 17.4 lb·ft)

Electric Water Pump (EWP) On Vehicle Inspection

Inspection
1.
The cooling system can be more quickly diagnosed for problems using the KDS (Refer to "DTC guide").
(1)
Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) using the KDS
(Refer to DTC guide when fault code is found.)
Information
Refer to the KDS screen for operating conditions and details

Electric Water Pump (EWP) Removal and Installation - 2WD

Removal
Warning
•
When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
•
When working a high voltage system, the technician must be recognized and observe "General Safety Information and Caution". If do not follow, serious accidents like electric shock and short circuit are caused.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Note
When disconnecting a quick connector, refer to the following according to the type of quick connector.
[Type A]
- Remove while pressing the quick connector clamp (A) in the direction of the arrow.

Cooling System — High Voltage Battery Cooling System / Electric Water Pump (EWP) / Removal and Installation - 2WD / Removal illustration

- Do not touch the rubber seal (A) inside the hose.

Cooling System — High Voltage Battery Cooling System / Electric Water Pump (EWP) / Removal and Installation - 2WD / Removal illustration

[Type B]
- Pull the quick connector clamp (A) in the direction of the arrow to separate the clamp and remove the hose.

Cooling System — High Voltage Battery Cooling System / Electric Water Pump (EWP) / Removal and Installation - 2WD / Removal illustration

- Do not touch the rubber seal (A) inside the hose.

Cooling System — High Voltage Battery Cooling System / Electric Water Pump (EWP) / Removal and Installation - 2WD / Removal illustration

#1 High Voltage Battery Electric Water Pump (EWP)
1.
Drain the high voltage battery coolant.
(Refer to High Voltage Battery Coolant - "Drain")
2.
Disconnect the reservoir tank cooling hose (A) after releasing the quick connector.

Cooling System — High Voltage Battery Cooling System / Electric Water Pump (EWP) / Removal and Installation - 2WD / Removal illustration

3.
Disconnect the high voltage battery EWP connector (A) and wiring clip (B).

Cooling System — High Voltage Battery Cooling System / Electric Water Pump (EWP) / Removal and Installation - 2WD / Removal illustration

4.
Disconnect the high voltage battery EWP cooling hose (A) after releasing the quick connector.

Cooling System — High Voltage Battery Cooling System / Electric Water Pump (EWP) / Removal and Installation - 2WD / Removal illustration

5.
Remove the high voltage battery EWP (A) after removing the bolts.

Tightening torque :
2.0 - 2.5 N·m (0.2 - 0.25 kgf·m, 1.4 - 1.8 lb·ft, 17.4 - 21.7 lb·in)

Cooling System — High Voltage Battery Cooling System / Electric Water Pump (EWP) / Removal and Installation - 2WD / Removal illustration

#2 High Voltage Battery Electric Water Pump (EWP)
1.
Drain the high voltage battery coolant.
(Refer to High Voltage Battery Coolant - "Drain")
2.
Disconnect the high voltage battery EWP cooling hoses (A) after releasing the quick connectors.

Cooling System — High Voltage Battery Cooling System / Electric Water Pump (EWP) / Removal and Installation - 2WD / Removal illustration

3.
Remove the wiring clips (A).

Cooling System — High Voltage Battery Cooling System / Electric Water Pump (EWP) / Removal and Installation - 2WD / Removal illustration

4.
Disconnect the high voltage battery EWP connector (A).

Cooling System — High Voltage Battery Cooling System / Electric Water Pump (EWP) / Removal and Installation - 2WD / Removal illustration

5.
Remove the high voltage battery EWP (A) after removing the bolt and nut.

Tightening torque :
6.9 - 9.8 N·m (0.7 - 1.0 kgf·m, 5.1 - 7.2 lb·ft)

Cooling System — High Voltage Battery Cooling System / Electric Water Pump (EWP) / Removal and Installation - 2WD / Removal illustration

Installation
Warning
•
When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
•
When working a high voltage system, the technician must be recognized and observe "General Safety Information and Caution". If do not follow, serious accidents like electric shock and short circuit are caused.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.
2.
Perform the air bleeding procedures using the KDS after refilling the coolant.
(Refer to High Voltage Battery Coolant - "Refilling")
Note
Perform "Battery EWP Operation Mode for Degassing and Circulation" to air bleeding using KDS when filling with coolant.

Electric Water Pump (EWP) Removal and Installation - 4WD

Removal
Warning
•
When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
•
When working a high voltage system, the technician must be recognized and observe "General Safety Information and Caution". If do not follow, serious accidents like electric shock and short circuit are caused.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Note
When disconnecting a quick connector, refer to the following according to the type of quick connector.
[Type A]
- Remove while pressing the quick connector clamp (A) in the direction of the arrow.

Cooling System — High Voltage Battery Cooling System / Electric Water Pump (EWP) / Removal and Installation - 4WD / Removal illustration

- Do not touch the rubber seal (A) inside the hose.

Cooling System — High Voltage Battery Cooling System / Electric Water Pump (EWP) / Removal and Installation - 4WD / Removal illustration

[Type B]
- Pull the quick connector clamp (A) in the direction of the arrow to separate the clamp and remove the hose.

Cooling System — High Voltage Battery Cooling System / Electric Water Pump (EWP) / Removal and Installation - 4WD / Removal illustration

- Do not touch the rubber seal (A) inside the hose.

Cooling System — High Voltage Battery Cooling System / Electric Water Pump (EWP) / Removal and Installation - 4WD / Removal illustration

#1 High Voltage Battery Electric Water Pump (EWP)
1.
Drain the high voltage battery coolant.
(Refer to High Voltage Battery Coolant - "Drain")
2.
Disconnect the reservoir tank cooling hose (A) after releasing the quick connector.

Cooling System — High Voltage Battery Cooling System / Electric Water Pump (EWP) / Removal and Installation - 4WD / Removal illustration

3.
Disconnect the high voltage battery EWP connector (A).

Cooling System — High Voltage Battery Cooling System / Electric Water Pump (EWP) / Removal and Installation - 4WD / Removal illustration

4.
Disconnect the high voltage battery EWP cooling hose (A) after releasing the quick connector.

Cooling System — High Voltage Battery Cooling System / Electric Water Pump (EWP) / Removal and Installation - 4WD / Removal illustration

5.
Remove the high voltage battery EWP (A) after removing the bolts.

Tightening torque :
2.0 - 2.5 N·m (0.2 - 0.25 kgf·m, 1.4 - 1.8 lb·ft, 17.4 - 21.7 lb·in)

Cooling System — High Voltage Battery Cooling System / Electric Water Pump (EWP) / Removal and Installation - 4WD / Removal illustration

#2 High Voltage Battery Electric Water Pump (EWP)
1.
Drain the high voltage battery coolant.
(Refer to High Voltage Battery Coolant - "Drain")
2.
Disconnect the high voltage battery EWP cooling hoses (A) after releasing the quick connectors.

Cooling System — High Voltage Battery Cooling System / Electric Water Pump (EWP) / Removal and Installation - 4WD / Removal illustration

3.
Disconnect the high voltage battery EWP connector (A) and wiring clip (B).

Cooling System — High Voltage Battery Cooling System / Electric Water Pump (EWP) / Removal and Installation - 4WD / Removal illustration

4.
Remove the high voltage battery EWP (A) after removing the bolts.

Tightening torque :
6.9 - 9.8 N·m (0.7 - 1.0 kgf·m, 5.1 - 7.2 lb·ft)

Cooling System — High Voltage Battery Cooling System / Electric Water Pump (EWP) / Removal and Installation - 4WD / Removal illustration

5.
Remove the high voltage battery EWP bracket.
(1)
Remove the wiring clip (A).
(2)
Remove the high voltage battery EWP bracket (B) after removing the bolts.

Tightening torque :
16.7 - 23.5 N·m (2.0 - 2.4 kgf·m, 14.5 - 17.3 lb·ft)

Cooling System — High Voltage Battery Cooling System / Electric Water Pump (EWP) / Removal and Installation - 4WD / Removal illustration

Installation
Warning
•
When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
•
When working a high voltage system, the technician must be recognized and observe "General Safety Information and Caution". If do not follow, serious accidents like electric shock and short circuit are caused.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.
2.
Perform the air bleeding procedures using the KDS after refilling the coolant.
(Refer to High Voltage Battery Coolant - "Refilling")
Note
Perform "Battery EWP Operation Mode for Degassing and Circulation" to air bleeding using KDS when filling with coolant.

Other information:

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Head-Up Display (HUD) : (if equipped)

The Kia EV6 Head-Up Display (HUD) is an advanced transparent projection system that displays important driving information directly onto the windshield within the driver’s field of vision. This technology allows the Kia EV6 driver to monitor critical driving information without taking attention away from the road ahead. The HUD system can display information from the instrument cluster, navigation system, and various driver assistance technologies in real time.

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Theft-alarm system

The theft-alarm system of the Kia EV6 is designed to help protect the vehicle against unauthorized access and potential theft attempts. This advanced security system monitors door, hood, and liftgate activity and activates warning functions if unauthorized entry is detected. The Kia EV6 theft-alarm system operates in three separate stages.

 
Copyright © 2026 Kia EV6 Manuals ⏱ 0.0242