Kia EV6: Cooling System / Cooling System

Contents:

Coolant Drain

Special Service Tool
Tool Name / Number
Illustration
Description
Coolant refiller & suction tool
0K253 - J2300

Cooling System — Cooling System / Coolant / Drain / Special Service Tool illustration

Used to drain and fill the coolant for EV
Cap adapter
0K253 - J2320

Cooling System — Cooling System / Coolant / Drain / Special Service Tool illustration

Used to drain and fill the coolant for EV

SST (0K253 - J2300) Detail Name

Cooling System — Cooling System / Coolant / Drain / Special Service Tool illustration

Cooling System — Cooling System / Coolant / Drain / Special Service Tool illustration

1. Pressure Valve
2. Suction Valve
3. Vacuum Valve 1
4. Vacuum Valve 2
5. Coolant Injection
6. Vacuum Valve
7. Regulator Pressure Gauge
8. Pressure Gauge
9. Vacuum Gauge
10. Air Pressurization Valve
11. Vacuum Outlet Valve
12. Air Hose Inlet Valve
13. Regulator Adjusting Knob

Drain
Warning
•
When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
•
When working a high voltage system, the technician must be recognized and observe "General Safety Information and Caution". If do not follow, serious accidents like electric shock and short circuit are caused.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Disconnect the battery negative ( - ) terminal and the high voltage service interlock connector.
(Refer to Battery Control System - "Auxiliary Battery (12 V)")
(Refer to Battery Control System - "Auxiliary Battery (12 V)" -4WD)
2.
Open the reservoir tank cap (A).

Cooling System — Cooling System / Coolant / Drain illustration

3.
Install the cap adapter (0K253 - J2320).

Cooling System — Cooling System / Coolant / Drain illustration

4.
Install the radiator cap connection hose (A) to the radiator cap adapter (B).

Cooling System — Cooling System / Coolant / Drain illustration

5.
Connect the radiator cap connection hose (A) to the air pressurization valve of SST (0K253 - J2300).

Cooling System — Cooling System / Coolant / Drain illustration

6.
Install the air hose (A) to the air inlet valve of SST (0K253 - J2300).

Cooling System — Cooling System / Coolant / Drain illustration

Note
Make sure all valves are closed.

Cooling System — Cooling System / Coolant / Drain illustration

7.
Turn the regulator adjusting knob (A) to set pressure gauge (B) to 0.2 Mpa.

Cooling System — Cooling System / Coolant / Drain illustration

Note
After adjusting the pressure, close the regulator adjustment knob.
8.
Remove the front under cover.
(Refer to Motor & Reduction Gear System - "Front Under Cover")
9.
Release the quick connector, and then disconnect the high voltage battery EWP cooling hose (A).
[2WD]

Cooling System — Cooling System / Coolant / Drain illustration

[4WD]

Cooling System — Cooling System / Coolant / Drain illustration

10.
Install the coolant drain adapter and hose (A) to the battery EWP and EWP cooling hose.
[2WD]

Cooling System — Cooling System / Coolant / Drain illustration

[4WD]

Cooling System — Cooling System / Coolant / Drain illustration

11.
Put the opposite of the coolant drain adapter and hose (A) to a bucket (B).

Cooling System — Cooling System / Coolant / Drain illustration

12.
Turn the pressure valve (A) the direction of the arrow to drain coolant.

Cooling System — Cooling System / Coolant / Drain illustration

Note
Make sure that the valves other than the pressure valve (A) are closed.
13.
Close the pressure valve after draining coolant, and then install the high voltage battery EWP coolant hose (A).
[2WD]

Cooling System — Cooling System / Coolant / Drain illustration

[4WD]

Cooling System — Cooling System / Coolant / Drain illustration

14.
Remove the rear under cover.
(Refer to Motor and Reduction Gear System - "Rear Under Cover")
15.
Disconnect the cooling hose (A) after releasing the quick connector.

Cooling System — Cooling System / Coolant / Drain illustration

16.
Install the coolant drain adapter and hose (A) to the cooling hose.

Cooling System — Cooling System / Coolant / Drain illustration

17.
Put the opposite of the coolant drain adapter and hose (A) to a bucket (B).

Cooling System — Cooling System / Coolant / Drain illustration

18.
Turn the pressure valve (A) the direction of the arrow to drain coolant.

Cooling System — Cooling System / Coolant / Drain illustration

Note
Make sure that the valves other than the pressure valve (A) are closed.
19.
Close the pressure valve after draining coolant, and then install the cooling hose (A).

Cooling System — Cooling System / Coolant / Drain illustration

20.
Separate the radiator cap connection hose (A) to the air pressurization valve.

Cooling System — Cooling System / Coolant / Drain illustration

Coolant Refilling

Special Service Tool
Tool Name / Number
Illustration
Description
Coolant refiller & suction tool
0K253 - J2300

Cooling System — Cooling System / Coolant / Refilling / Special Service Tool illustration

Used to drain and fill the coolant for EV
Cap adapter
0K253 - J2320

Cooling System — Cooling System / Coolant / Refilling / Special Service Tool illustration

Used to drain and fill the coolant for EV

SST (0K253 - J2300) Detail Name

Cooling System — Cooling System / Coolant / Refilling / Special Service Tool illustration

Cooling System — Cooling System / Coolant / Refilling / Special Service Tool illustration

1. Pressure Valve
2. Suction Valve
3. Vacuum Valve 1
4. Vacuum Valve 2
5. Coolant Injection
6. Vacuum Valve
7. Regulator Pressure Gauge
8. Pressure Gauge
9. Vacuum Gauge
10. Air Pressurization Valve
11. Vacuum Outlet Valve
12. Air Hose Inlet Valve
13. Regulator Adjusting Knob

Refilling
Note
•
Be careful not to spill coolant on the electric devices when replacing the coolant.
•
Use genuine antifreeze/coolant.
•
To prevent corrosion, the concentration of coolant should be maintained at a minimum of 45%. If the coolant concentration is less than 45%, there may be a risk of corrosion or freezing.
•
It is not recommended if the concentration of the coolant exceeds 60%, as the cooling effect may be reduced.
•
Do not mix antifreeze/coolant from different brands.
•
Do not add any anti-rust.
1.
Drain the coolant.
(Refer to Coolant - "Drain")
2.
Connect the radiator cap connection hose (A) to the vacuum valve of SST (0K253 - J2300).

Cooling System — Cooling System / Coolant / Refilling illustration

3.
Open the vacuum valve (A) in the direction of the arrow, and then close when the vacuum gauge (B) reaches the green area (C).

Cooling System — Cooling System / Coolant / Refilling illustration

Note
Make sure that the valves other than the vacuum valve (A) are closed.
4.
Connect the coolant suction hose (A) to SST (0K253 - J2300) coolant filler valve and place the opposite hose in the bucket (B) containing new coolant.

Cooling System — Cooling System / Coolant / Refilling illustration

5.
Turn the suction valve (A) in the direction of the arrow to fill new coolant, and then close it when the vacuum gauge reaches to '0'.

Cooling System — Cooling System / Coolant / Refilling illustration

Note
Check that the valve except the suction valve (A) is locked.
6.
Remove the cap adapter (0K253 - J2320).

Cooling System — Cooling System / Coolant / Refilling illustration

7.
Perform the order below with the KDS.
(S/W Management → Vehicle Control → Electric Water Pump Control)
Note
Charge the auxiliary 12 V battery during performing "Electric Water Pump Control" to prevent battery drain.
Information
When driving EWP, operate within 10 minutes.
8.
When the EWP operates and coolant circulates, refill coolant so that the coolant level is kept between "MAX" and "MIN" level.

Cooling System — Cooling System / Coolant / Refilling illustration

Note
Friction may damage the bearing if the EWP is operated without coolant.
9.
When the operational sound volume of the EWP becomes small and when no air bubbles can be seen in the reservoir tank, bleeding of the coolant system is completed.
Note
•
After air bleeding is completed make sure that coolant in the reservoir tank flow without air bubble during the EWP actuation.
•
If the coolant flow is not seen or air bubbles are still seen, repeat steps 7 to 8.
10.
Perform the order below with the KDS.
(Actuation Test → Vehicle Control → Battery EWP Operation Mode for Degassing and Circulation)
Note
Charge the auxiliary 12 V battery during performing "Battery Electric Water Pump Control" to prevent battery drain.
Information
When driving EWP, operate within 10 minutes.
11.
When the battery EWP operates and coolant circulates, refill coolant so that the coolant level is kept between "MAX" and "MIN" level.

Cooling System — Cooling System / Coolant / Refilling illustration

Note
Friction may damage the bearing if the EWP is operated without coolant.
12.
When the operational sound volume of the EWP becomes small and when no air bubbles can be seen in the reservoir tank, bleeding of the coolant system is completed.
Note
•
After air bleeding is completed make sure that coolant in the reservoir flow without air bubble during the EWP actuation.
•
If the coolant flow is not seen or air bubbles are still seen, repeat steps 10 to 11.
13.
After air bleeding is completed, refill the coolant to the MAX level and install the reservoir cap.

Cooling System — Cooling System / Coolant / Refilling illustration

14.
Check the coolant for leakage.
Note
The cooling system air bleeding and coolant injection are performed perfectly when the coolant is completely cooled. Check the coolant level of the reservoir tank for 2 - 3 days after flushing the coolant.
15.
Install the front under cover.
(Refer to Motor & Reduction Gear System - "Front Under Cover")
16.
Install the rear under cover.
(Refer to Motor and Reduction Gear System - "Rear Under Cover")

Cooling Fan Specification. Cooling Fan Components and Components Location

Cooling Fan Specification

Specification
Item
Specification
Control type
PWM
Fan speed (rpm)
2,352 - 2,548
Current consumption (A)
44.1 - 53.9

Cooling Fan Components and Components Location

Component and Component Location

Cooling System — Cooling System / Cooling Fan / Components and Components Location / Component and Component Location illustration

1. Cooling Fan Assembly
1-a. 4.9 - 7.8 N·m (0.5 - 0.8 kgf·m, 3.6 - 5.8 lb·ft, 43.4 - 69.4 lb·in)

Cooling Fan On Vehicle Inspection

Inspection
1.
The cooling system can be more quickly diagnosed for problems using the KDS (Refer to "DTC guide").
(1)
Actuation test : Checking the system operation condition
(Data Analysis → Actuation Test → Radiator Fan Forced Operation)
Information
Refer to the KDS screen for operating conditions and details

Cooling Fan Removal and Installation - 2WD

Removal
Warning
•
When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
•
When working a high voltage system, the technician must be recognized and observe "General Safety Information and Caution". If do not follow, serious accidents like electric shock and short circuit are caused.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Remove the front trunk.
(Refer to Body - "Front Trunk")
2.
Disconnect the cooling fan connector (A).

Cooling System — Cooling System / Cooling Fan / Removal and Installation - 2WD / Removal illustration

3.
Separate the radiator upper hose clips (A).

Cooling System — Cooling System / Cooling Fan / Removal and Installation - 2WD / Removal illustration

4.
Remove the cooling fan bolts (A).

Tightening torque :
4.9 - 7.8 N·m (0.5 - 0.8 kgf·m, 3.6 - 5.8 lb·ft, 43.4 - 69.4 lb·in)

[LH]

Cooling System — Cooling System / Cooling Fan / Removal and Installation - 2WD / Removal illustration

[RH]

Cooling System — Cooling System / Cooling Fan / Removal and Installation - 2WD / Removal illustration

5.
Remove the cooling fan assembly (A).

Cooling System — Cooling System / Cooling Fan / Removal and Installation - 2WD / Removal illustration

Installation
1.
Install in the reverse order of removal.

Cooling Fan Removal and Installation - 4WD

Removal
Warning
•
When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
•
When working a high voltage system, the technician must be recognized and observe "General Safety Information and Caution". If do not follow, serious accidents like electric shock and short circuit are caused.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Remove the front trunk.
(Refer to Body - "Front Trunk")
2.
Remove the auxiliary 12 V battery tray.
(Refer to Battery Control System - "Auxiliary 12 V Battery")
3.
Disconnect the cooling fan connector (A).

Cooling System — Cooling System / Cooling Fan / Removal and Installation - 4WD / Removal illustration

4.
Separate the radiator upper hose clips (A).

Cooling System — Cooling System / Cooling Fan / Removal and Installation - 4WD / Removal illustration

5.
Remove the cooling fan bolts (A).

Tightening torque :
4.9 - 7.8 N·m (0.5 - 0.8 kgf·m, 3.6 - 5.8 lb·ft, 43.4 - 69.4 lb·in)

[LH]

Cooling System — Cooling System / Cooling Fan / Removal and Installation - 4WD / Removal illustration

[RH]

Cooling System — Cooling System / Cooling Fan / Removal and Installation - 4WD / Removal illustration

6.
Remove the cooling fan assembly (A).

Cooling System — Cooling System / Cooling Fan / Removal and Installation - 4WD / Removal illustration

Installation
1.
Install in the reverse order of removal.

Radiator Components and Components Location

Component and Component Location

Cooling System — Cooling System / Radiator / Components and Components Location / Component and Component Location illustration

1. Low Temperature Radiator
1-a. 4.9 - 7.8 N·m (0.5 - 0.8 kgf·m, 3.6 - 5.8 lb·ft, 43.4 - 69.4 lb·in)
2. High Temperature Radiator

Radiator Removal and Installation

Removal
Warning
•
When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
•
When working a high voltage system, the technician must be recognized and observe "General Safety Information and Caution". If do not follow, serious accidents like electric shock and short circuit are caused.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Note
Follow the instructions below when releasing the quick connector.
- Pull the quick connector clamp (A) in the direction of the arrow to separate the clamp and remove the hose.

Cooling System — Cooling System / Radiator / Removal and Installation / Removal illustration

- Do not touch the rubber seal (A) inside the hose.

Cooling System — Cooling System / Radiator / Removal and Installation / Removal illustration

Low Temperature Radiator
1.
Drain the coolant.
(Refer to Coolant - "Drain")
2.
Remove the front trunk.
(Refer to Body - "Front Trunk")
3.
Remove the front bumper beam.
(Refer to Body - "Front Bumper Beam Assembly")
4.
Disconnect the high temperature radiator upper cooling hose (A) after releasing the quick connector.

Cooling System — Cooling System / Radiator / Removal and Installation / Removal illustration

5.
Disconnect the low temperature radiator upper cooling hose (A) after releasing the quick connector.

Cooling System — Cooling System / Radiator / Removal and Installation / Removal illustration

6.
Remove the cooling fan.
(Refer to Cooling Fan - "Removal and Installation - 2WD")
(Refer to Cooling Fan - "Removal and Installation - 4WD")
7.
Remove the wiring clip (A).

Cooling System — Cooling System / Radiator / Removal and Installation / Removal illustration

8.
Remove the radiator upper air guard (A) after removing the bolts.

Tightening torque :
7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)

Cooling System — Cooling System / Radiator / Removal and Installation / Removal illustration

9.
Remove the radiator lower air guard (A) after removing the bolts.

Tightening torque :
7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)

Cooling System — Cooling System / Radiator / Removal and Installation / Removal illustration

10.
Remove the condenser pipe bolt (A).

Tightening torque :
7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)

Cooling System — Cooling System / Radiator / Removal and Installation / Removal illustration

11.
Separate the condenser (A) after removing the bolts.

Tightening torque :
4.9 - 7.8 N·m (0.5 - 0.8 kgf·m, 3.6 - 5.8 lb·ft, 43.4 - 69.4 lb·in)

Cooling System — Cooling System / Radiator / Removal and Installation / Removal illustration

12.
Disconnect the high temperature radiator lower cooling hose (A) and low temperature radiator lower cooling hose (B) after releasing the quick connectors.

Cooling System — Cooling System / Radiator / Removal and Installation / Removal illustration

13.
Remove the radiator upper bracket (A) after removing the bolts.

Tightening torque :
7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)

[LH]

Cooling System — Cooling System / Radiator / Removal and Installation / Removal illustration

[RH]

Cooling System — Cooling System / Radiator / Removal and Installation / Removal illustration

14.
Remove the high and low temperature radiators (A).

Cooling System — Cooling System / Radiator / Removal and Installation / Removal illustration

15.
Remove the low temperature radiator bolts (A).

Tightening torque :
4.9 - 7.8 N·m (0.5 - 0.8 kgf·m, 3.6 - 5.8 lb·ft, 43.4 - 69.4 lb·in)

Cooling System — Cooling System / Radiator / Removal and Installation / Removal illustration

16.
Remove the low temperature radiator (A).

Cooling System — Cooling System / Radiator / Removal and Installation / Removal illustration

High Temperature Radiator
1.
Remove the high and low temperature radiators.
2.
Remove the low temperature radiator bolts (A).

Tightening torque :
4.9 - 7.8 N·m (0.5 - 0.8 kgf·m, 3.6 - 5.8 lb·ft, 43.4 - 69.4 lb·in)

Cooling System — Cooling System / Radiator / Removal and Installation / Removal illustration

3.
Remove the high temperature radiator (A).

Cooling System — Cooling System / Radiator / Removal and Installation / Removal illustration

Installation
1.
Install in the reverse order of removal.
2.
Perform the air bleeding procedures using the KDS after refilling the coolant.
(Refer to Coolant - "Refilling")
Note
Perform "Electric Water Pump Control" and "Battery EWP Operation Mode for Degassing and Circulation" to air bleeding using KDS when filling with coolant.

Active Air Flap (AAF) Components and Components Location. Active Air Flap (AAF) On Vehicle Inspection

Active Air Flap (AAF) Components and Components Location

Component and Component Location

Cooling System — Cooling System / Active Air Flap (AAF) / Components and Components Location / Component and Component Location illustration

1. Front Bumper Assembly
2. Active Air Flap (AAF)
2-a. 1.0 - 2.0 N·m (0.1 - 0.2 kgf·m, 0.7 - 1.4 lb·ft, 8.7 - 17.4 lb·in)
3. Active Air Flap Actuator
3-a. 1.0 - 2.0 N·m (0.1 - 0.2 kgf·m, 0.7 - 1.4 lb·ft, 8.7 - 17.4 lb·in)

Active Air Flap (AAF) On Vehicle Inspection

Inspection
1.
The cooling system can be more quickly diagnosed for problems using the KDS (Refer to "DTC guide").
(1)
Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) using the KDS
(Refer to DTC guide when fault code is found.)
Information
Refer to the KDS screen for operating conditions and details

Active Air Flap (AAF) Removal and Installation

Removal
Active Air Flap (AAF)
1.
Remove the front bumper.
(Refer to Body - "Front Bumper Assembly")
2.
Disconnect the AAF actuator connector (A).

Cooling System — Cooling System / Active Air Flap (AAF) / Removal and Installation / Removal illustration

3.
Disconnect the ambient temperature sensor connector (A).

Cooling System — Cooling System / Active Air Flap (AAF) / Removal and Installation / Removal illustration

4.
Remove the AAF (A) after removing the screws.

Tightening torque :
1.0 - 2.0 N·m (0.1 - 0.2 kgf·m, 0.7 - 1.4 lb·ft, 8.7 - 17.4 lb·in)

Cooling System — Cooling System / Active Air Flap (AAF) / Removal and Installation / Removal illustration

Active Air Flap (AAF) Actuator
1.
Disconnect the AAF actuator connector (A).

Cooling System — Cooling System / Active Air Flap (AAF) / Removal and Installation / Removal illustration

2.
Remove the AAF actuator (A) after removing the screws.

Tightening torque :
1.0 - 2.0 N·m (0.1 - 0.2 kgf·m, 0.7 - 1.4 lb·ft, 8.7 - 17.4 lb·in)

Cooling System — Cooling System / Active Air Flap (AAF) / Removal and Installation / Removal illustration

Installation
1.
Install in the reverse order of removal.

Reservoir Tank Removal and Installation - 2WD

Removal
Warning
•
When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
•
When working a high voltage system, the technician must be recognized and observe "General Safety Information and Caution". If do not follow, serious accidents like electric shock and short circuit are caused.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Note
When disconnecting a quick connector, refer to the following according to the type of quick connector.
[Type A]
- Remove while pressing the quick connector clamp (A) in the direction of the arrow.

Cooling System — Cooling System / Reservoir Tank / Removal and Installation - 2WD / Removal illustration

- Do not touch the rubber seal (A) inside the hose.

Cooling System — Cooling System / Reservoir Tank / Removal and Installation - 2WD / Removal illustration

[Type B]
- Pull the quick connector clamp (A) in the direction of the arrow to separate the clamp and remove the hose.

Cooling System — Cooling System / Reservoir Tank / Removal and Installation - 2WD / Removal illustration

- Do not touch the rubber seal (A) inside the hose.

Cooling System — Cooling System / Reservoir Tank / Removal and Installation - 2WD / Removal illustration

1.
Remove the front trunk.
(Refer to Body - "Front Trunk")
2.
Drain the coolant.
(Refer to Coolant - "Drain")
3.
Remove the 3 way valve.
(Refer to Motor Cooling System - "3 Way Valve")
4.
Disconnect the reservoir tank cooling hose (A) after releasing the quick connector.

Cooling System — Cooling System / Reservoir Tank / Removal and Installation - 2WD / Removal illustration

5.
Disconnect the high voltage battery EWP connector (A) and wiring clip (B).

Cooling System — Cooling System / Reservoir Tank / Removal and Installation - 2WD / Removal illustration

6.
Disconnect the motor EWP connector (A).

Cooling System — Cooling System / Reservoir Tank / Removal and Installation - 2WD / Removal illustration

7.
Disconnect the motor EWP cooling hose (A) after releasing the quick connector.

Cooling System — Cooling System / Reservoir Tank / Removal and Installation - 2WD / Removal illustration

8.
Disconnect the high voltage battery EWP cooling hose (A) after releasing the quick connector.

Cooling System — Cooling System / Reservoir Tank / Removal and Installation - 2WD / Removal illustration

9.
Remove the reservoir tank assembly (A) after removing the bolts and nut.

Tightening torque :
7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)

Cooling System — Cooling System / Reservoir Tank / Removal and Installation - 2WD / Removal illustration

10.
Remove the electric water pump (A) after removing the bolts.

Tightening torque :
2.0 - 2.5 N·m (0.2 - 0.25 kgf·m, 1.4 - 1.8 lb·ft, 17.4 - 21.7 lb·in)

[Motor]

Cooling System — Cooling System / Reservoir Tank / Removal and Installation - 2WD / Removal illustration

[Battery]

Cooling System — Cooling System / Reservoir Tank / Removal and Installation - 2WD / Removal illustration

11.
Remove the reservoir tank (A) after removing the bolts.

Tightening torque :
7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)

Cooling System — Cooling System / Reservoir Tank / Removal and Installation - 2WD / Removal illustration

Installation
1.
Install in the reverse order of removal.
2.
Perform the air bleeding procedures using the KDS after refilling the coolant.
(Refer to Coolant - "Refilling")
Note
Perform "Electric Water Pump Control" and "Battery EWP Operation Mode for Degassing and Circulation" to air bleeding using KDS when filling with coolant.

Reservoir Tank Removal and Installation - 4WD

Removal
Warning
•
When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
•
When working a high voltage system, the technician must be recognized and observe "General Safety Information and Caution". If do not follow, serious accidents like electric shock and short circuit are caused.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Note
When disconnecting a quick connector, refer to the following according to the type of quick connector.
[Type A]
- Remove while pressing the quick connector clamp (A) in the direction of the arrow.

Cooling System — Cooling System / Reservoir Tank / Removal and Installation - 4WD / Removal illustration

- Do not touch the rubber seal (A) inside the hose.

Cooling System — Cooling System / Reservoir Tank / Removal and Installation - 4WD / Removal illustration

[Type B]
- Pull the quick connector clamp (A) in the direction of the arrow to separate the clamp and remove the hose.

Cooling System — Cooling System / Reservoir Tank / Removal and Installation - 4WD / Removal illustration

- Do not touch the rubber seal (A) inside the hose.

Cooling System — Cooling System / Reservoir Tank / Removal and Installation - 4WD / Removal illustration

1.
Remove the front trunk.
(Refer to Body - "Front Trunk")
2.
Drain the coolant.
(Refer to Coolant - "Drain")
3.
Remove the 3 way valve.
(Refer to Motor Cooling System - "3 Way Valve")
4.
Disconnect the reservoir tank cooling hose (A) after releasing the quick connector.

Cooling System — Cooling System / Reservoir Tank / Removal and Installation - 4WD / Removal illustration

5.
Disconnect the high voltage battery EWP connector (A) and wiring clip (B).

Cooling System — Cooling System / Reservoir Tank / Removal and Installation - 4WD / Removal illustration

6.
Disconnect the motor EWP connector (A).

Cooling System — Cooling System / Reservoir Tank / Removal and Installation - 4WD / Removal illustration

7.
Disconnect the motor EWP cooling hose (A) after releasing the quick connector.

Cooling System — Cooling System / Reservoir Tank / Removal and Installation - 4WD / Removal illustration

8.
Disconnect the water condenser cooling hose (A) after releasing the quick connector.

Cooling System — Cooling System / Reservoir Tank / Removal and Installation - 4WD / Removal illustration

9.
Disconnect the high voltage battery EWP cooling hose (A) after releasing the quick connector.

Cooling System — Cooling System / Reservoir Tank / Removal and Installation - 4WD / Removal illustration

10.
Remove the reservoir tank assembly (A) after removing the bolts and nut.

Tightening torque :
7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)

Cooling System — Cooling System / Reservoir Tank / Removal and Installation - 4WD / Removal illustration

11.
Remove the electric water pump (A) after removing the bolts.

Tightening torque :
2.0 - 2.5 N·m (0.2 - 0.25 kgf·m, 1.4 - 1.8 lb·ft, 17.4 - 21.7 lb·in)

[Motor]

Cooling System — Cooling System / Reservoir Tank / Removal and Installation - 4WD / Removal illustration

[Battery]

Cooling System — Cooling System / Reservoir Tank / Removal and Installation - 4WD / Removal illustration

12.
Remove the reservoir tank (A) after removing the bolts.

Tightening torque :
7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)

Cooling System — Cooling System / Reservoir Tank / Removal and Installation - 4WD / Removal illustration

Installation
1.
Install in the reverse order of removal.
2.
Perform the air bleeding procedures using the KDS after refilling the coolant.
(Refer to Coolant - "Refilling")
Note
Perform "Electric Water Pump Control" and "Battery EWP Operation Mode for Degassing and Circulation" to air bleeding using KDS when filling with coolant.

Other information:

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Operating conditions

The Rear View Monitor image remains active when the following conditions are satisfied: The gear is shifted from R (Reverse) to N (Neutral) or D (Drive). The Kia EV6 speed remains below approximately 6 mph (10 km/h). Non-operating conditions The Extended Rear View Monitor turns OFF under the following conditions: The gear is shifted to P (Park).

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Deleting the shared keys

Select Setup > Vehicle > Digital Keys > Smartphone key > Shared Keys > [Group] > Delete All on the Kia EV6 infotainment system screen. All smartphone digital keys other than the owner’s My Smartphone Key are grouped and displayed as Shared Keys within the Kia EV6 Digital Key 2 management menu. If multiple devices use the same smartphone account, they will appear under the same [Group] classification.

 
Copyright © 2026 Kia EV6 Manuals ⏱ 0.0155