Kia EV6: Cooling System

Contents:

Single-Use Parts

Single-Use Parts
Non-reusable parts (Single-Use Parts)
Workshop manual provides “Components and Components Location� which can be used to identify “Non-reusable parts�. When repairing a vehicle, Non-reusable parts such as fasteners, gaskets, washers, clips and garnishes must be replaced. Kia Non-reusable parts are designed to be installed only once.
Before working on a vehicle, check “Components and Components Location� to find the non-reusable parts in a system.
※ Symbol of Non-reusable parts
Symbol
Meaning

Cooling System — Single-Use Parts illustration

Do not reuse the part. Replace with a new one.

※ Example of “Components and Components Location�

Cooling System — Single-Use Parts illustration

High Voltage System General Safety Information and Caution ➤

High Voltage Shut-off Procedures

High Voltage Shut-off Procedures

High Voltage Shut-off Procedures
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Information
High Voltage Component : Battery System Assembly (BSA), motor assembly, inverter assembly, high voltage junction box, power cable, etc.
1.
Check the Battery Management Unit (BMU) weld flag with the KDS.
(Data Analysis → Battery Management System (BMS) → BMU Weld Flag)

Specified value : NO

Information
Refer to the KDS screen for operating conditions and details.
2.
Open the front trunk (A).

Cooling System — High Voltage Shut-off Procedures illustration

3.
Open the low voltage (12 V) battery service cover (A).

Cooling System — High Voltage Shut-off Procedures illustration

4.
Turn the POWER OFF, separate the low voltage (12 V) battery ( - ) terminal (A).

Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)

Cooling System — High Voltage Shut-off Procedures illustration

5.
Disconnect the service interlock connector (A).

Cooling System — High Voltage Shut-off Procedures illustration

Warning
•
Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
•
When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
Note
The service interlock connector cannot be completely removed.

Cooling System — High Voltage Shut-off Procedures illustration

6.
Remove the front under cover.
(Refer to Motor and Reduction Gear System - "Front Under Cover")
7.
Remove the high voltage battery cover (A).

Tightening torque :
7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)

Cooling System — High Voltage Shut-off Procedures illustration

8.
Disconnect the front high voltage junction box power cable (A).

Cooling System — High Voltage Shut-off Procedures illustration

Note
How to disconnect the connector
1)
Release the locking clip (A) by pulling it.
2)
Disconnect the connector by pushing the lever (A) in the direction of the arrow while pressing the locking clip (B).

Cooling System — High Voltage Shut-off Procedures illustration

9.
Remove the center floor rear under cover.
(Refer to Motor and Reduction Gear System - "Rear Under Cover")
10.
Disconnect the Integrated Charge Control Unit (ICCU) connector (A).

Cooling System — High Voltage Shut-off Procedures illustration

Note
How to disconnect the connector
1)
Release the locking clip (A) by pulling it.
2)
Disconnect the connector while pressing the locking clip (B).

Cooling System — High Voltage Shut-off Procedures illustration

11.
Disconnect the rear high voltage junction box power cable (A).

Cooling System — High Voltage Shut-off Procedures illustration

Note
How to disconnect the connector
1)
Release the locking clip (A) by pulling it.
2)
Disconnect the connector by pushing the lever (A) in the direction of the arrow while pressing the locking clip (B).

Cooling System — High Voltage Shut-off Procedures illustration

12.
Measure the voltage between the high voltage power connector and high voltage battery terminal to check whether the high voltage is shut-off.

30 V or less : Normal cut off high voltage circuit
Above 30 V : Fault on high voltage circuit

(1)
Measure the voltage between the high voltage power connector positive ( + ) terminal and negative ( - ) terminal.

Cooling System — High Voltage Shut-off Procedures illustration

(2)
Measure the voltage between the high voltage battery positive ( + ) and negative ( - ) terminal.

Cooling System — High Voltage Shut-off Procedures illustration

(3)
Measure the voltage between the high voltage battery positive ( + ) terminal and ground.

Cooling System — High Voltage Shut-off Procedures illustration

(4)
Measure the voltage between the high voltage battery negative ( - ) terminal and ground.

Cooling System — High Voltage Shut-off Procedures illustration

(5)
Measure the voltage between the rear high voltage battery positive ( + ) and negative ( - ) terminal.

Cooling System — High Voltage Shut-off Procedures illustration

(6)
Measure the voltage between the rear high voltage battery positive ( + ) terminal and ground.

Cooling System — High Voltage Shut-off Procedures illustration

(7)
Measure the voltage between the rear high voltage battery negative ( - ) terminal and ground.

Cooling System — High Voltage Shut-off Procedures illustration

Warning
1)
Check for insulation breakdown via KDS and physical leakage current before working on EV.
2)
Remove the main fuse if insulation breakdown or leakage current is suspected. (Remove the main fuse even when DTC CODE ON such as PRA malfunction)
(Refer to High Voltage Battery Control System - "Main Fuse")
※ If there is no insulation breakdown or leakage current and it is normal, work without removing the main fuse.

Specification ➤

Special Service Tools. Flow Diagram

Special Service Tools

Special Service Tool
Tool Name / Number
Illustration
Description
Coolant refiller & suction tool
0K253 - J2300

Cooling System — Special Service Tools / Special Service Tool illustration

Used to drain and fill the coolant for EV
Cap adapter
0K253 - J2320

Cooling System — Special Service Tools / Special Service Tool illustration

Used to drain and fill the coolant for EV

Flow Diagram

Coolant Flow
â–  Heat Pump

Cooling System — Flow Diagram / Coolant Flow illustration

HTR : High-Temperature Radiator
LTR : Low-Temperature Radiator
â–  Non Heat Pump

Cooling System — Flow Diagram / Coolant Flow illustration

HTR : High-Temperature Radiator
LTR : Low-Temperature Radiator

High Voltage Battery Cooling System ➤

Cooling System ➤

Motor Cooling System ➤

Other information:

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Limitations of Blind-Spot Collision-Avoidance Assist

The Kia EV6 Blind-Spot Collision-Avoidance Assist system may operate unexpectedly, become temporarily limited, or fail to detect surrounding vehicles properly under certain road, weather, traffic, or environmental conditions. Because the Kia EV6 Blind-Spot Collision-Avoidance Assist system relies on radar sensors and electronic detection technology, detection performance can vary depending on surrounding obstacles, road geometry, weather, and driving behavior.

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: To operate

Pull and hold the left-side ( ) Kia EV6 paddle shifter while coasting. When the Kia EV6 speed exceeds approximately 2 mph (3 km/h), the regenerative braking level returns to the previously selected setting after the paddle shifter is released. When the Kia EV6 speed drops below approximately 2 mph (3 km/h), vehicle stopping control remains active even after the paddle shifter is released.

Contents

Categories

 
Copyright © 2026 Kia EV6 Manuals � 0.0127