Kia EV6: Body (Interior / Exterior / Electrical) / Tailgate

Contents:

Components and Components Location. On Vehicle Inspection

Components and Components Location

Component and Component Location
Tailgate

Body (Interior / Exterior / Electrical) — Tailgate / Components and Components Location / Component and Component Location illustration

1. Tailgate Upper Trim
2. Tailgate Side Trim
3. Tailgate Lower Trim
4. Tailgate Lifter
5. Tailgate Weatherstrip
6. Tailgate Assembly
6-a. 21.6 - 26.5 N·m (2.2 - 2.7 kgf·m, 15.9 - 19.5 lb·ft)
7. Tailgate Latch
7-a. 6.9 - 8.8 N·m (0.7 - 0.9 kgf·m, 5.1 - 6.5 lb·ft)
8. Tailgate striker
8-a. 21.6 - 26.5 N·m (2.2 - 2.7 kgf·m, 15.9 - 19.5 lb·ft)
9. Tailgate Outside Handle Switch

On Vehicle Inspection

On Vehicle Inspection
Diagnostic with KDS
1.
The power tailgate system can quickly diagnosed for problems with the KDS. (Refer to "DTC guide")
(1)
Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS.
(Refer to DTC guide when fault code is found.)
(2)
S/W Management : Controlling other features including system option setting and zero point adjustment.
(S/W Management → Power Tailgate → Power Tailgate Mode Configuration)
Information
Refer to the KDS screen for operating conditions and details

Adjustment

Adjustment
1.
Place the car on a flat surface and check whether the body and tailgate are well-aligned.
2.
Loosen the tailgate hinge (A) bolts, adjust the gap by moving the tailgate back and forth, left and right, and then tighten the bolts.
3.
Adjust the gap between the tailgate and body by turning the overslam bumpers (B).
4.
Loosen the striker (C) screws, adjust the striker by moving the striker back and forth, left and right, and then tighten the screws
5.
Check that the tailgate opens and closes properly.

Body (Interior / Exterior / Electrical) — Tailgate / Adjustment illustration

Power Tailgate Buzzer Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Remove the tailgate lower trim.
(Refer to Tailgate - "Tailgate Trim")
2.
Remove the power tailgate buzzer (B) after disconnecting the connector (A).

Body (Interior / Exterior / Electrical) — Tailgate / Power Tailgate Buzzer / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Power Tailgate Unit Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Remove the luggage side trim [Driver's side].
(Refer to Luggage Trim - "Luggage Side Trim")
2.
Disconnect the power tailgate module connectors (A).

Body (Interior / Exterior / Electrical) — Tailgate / Power Tailgate Unit / Removal and Installation / Removal illustration

3.
Remove the power tailgate module (A) after removing the nuts.

Tightening torque :
3.9 - 5.9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)

Body (Interior / Exterior / Electrical) — Tailgate / Power Tailgate Unit / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.
2.
Perform the order below with the KDS when replacing the power tailgate unit.
(S/W Management → Power Tailgate → Power Tailgate Mode Configuration)
Information
Refer to the KDS screen for operating conditions and details
3.
Perform power tailgate initialization according to the procedure below.
(1)
Press the power tailgate switch and the outside handle switch simultaneously.
(2)
After pressing for more than 3 seconds, check the “beep” buzzer sound.
(3)
Manually close the power tailgate completely.
(4)
Press the outside handle switch.
(5)
The power tailgate opens at the same time as the "beep - beep -" buzzer sounds, and initialization is completed.
4.
Perform Over The Air (OTA) controller S/W update with KDS.
(Refer to Security & Vehicle Ignition System - "Over The Air (OTA)")

Tailgate Assembly Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Remove the tailgate lower trim.
(Refer to Tailgate - "Tailgate Trim")
2.
Separate the wiring harness (A) after disconnecting the connector.

Body (Interior / Exterior / Electrical) — Tailgate / Tailgate Assembly / Removal and Installation / Removal illustration

3.
Remove the tailgate lift (B) after removing the clips (A).
[Driver's Side]

Body (Interior / Exterior / Electrical) — Tailgate / Tailgate Assembly / Removal and Installation / Removal illustration

[Passenger's Side]

Body (Interior / Exterior / Electrical) — Tailgate / Tailgate Assembly / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Tailgate / Tailgate Assembly / Removal and Installation / Removal illustration

4.
Remove the tailgate assembly (A) after removing the bolts.

Tightening torque :
21.6 - 26.5 N·m (2.2 - 2.7 kgf·m, 15.9 - 19.5 lb·ft)

Body (Interior / Exterior / Electrical) — Tailgate / Tailgate Assembly / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Tailgate Latch Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Remove the tailgate lower trim.
(Refer to Tailgate - "Tailgate Trim")
2.
Separate the power tailgate latch connector (A).

Body (Interior / Exterior / Electrical) — Tailgate / Tailgate Latch / Removal and Installation / Removal illustration

3.
Remove the latch (A) after removing the bolts.

Tightening torque :
6.9 - 8.8 N·m (0.7 - 0.9 kgf·m, 5.1 - 6.5 lb·ft)

Body (Interior / Exterior / Electrical) — Tailgate / Tailgate Latch / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Tailgate Lifter Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Tailgate Lifter
1.
Remove the rear pillar trim.
(Refer to Interior Trim - "Rear Pillar Trim")
2.
Disconnect the lifter connectors (A).

Body (Interior / Exterior / Electrical) — Tailgate / Tailgate Lifter / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Tailgate / Tailgate Lifter / Removal and Installation / Removal illustration

3.
Remove the lifter (B) after releasing the clips (A).

Body (Interior / Exterior / Electrical) — Tailgate / Tailgate Lifter / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Tailgate / Tailgate Lifter / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Tailgate Switch Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Power Tailgate Inner Switch
1.
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
(1)
Open the front trunk (A).

Body (Interior / Exterior / Electrical) — Tailgate / Tailgate Switch / Removal and Installation / Removal illustration

(2)
Open the auxiliary 12 V battery service cover (A).

Body (Interior / Exterior / Electrical) — Tailgate / Tailgate Switch / Removal and Installation / Removal illustration

(3)
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).

Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)

Body (Interior / Exterior / Electrical) — Tailgate / Tailgate Switch / Removal and Installation / Removal illustration

(4)
Disconnect the service interlock connector (A).

Body (Interior / Exterior / Electrical) — Tailgate / Tailgate Switch / Removal and Installation / Removal illustration

Warning
•
Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
•
When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
Note
The service interlock connector cannot be completely removed.

Body (Interior / Exterior / Electrical) — Tailgate / Tailgate Switch / Removal and Installation / Removal illustration

2.
Separate the switch (A).

Body (Interior / Exterior / Electrical) — Tailgate / Tailgate Switch / Removal and Installation / Removal illustration

3.
Remove the switch (A) after disconnecting the connector (B).

Body (Interior / Exterior / Electrical) — Tailgate / Tailgate Switch / Removal and Installation / Removal illustration

Power Tailgate Outside Handle Switch
1.
Remove the tailgate lower trim.
(Refer to Tailgate - "Tailgate Trim")
2.
Disconnecting the switch connector (A).

Body (Interior / Exterior / Electrical) — Tailgate / Tailgate Switch / Removal and Installation / Removal illustration

3.
Remove the switch (A) by pulling it in the direction of the arrow.

Body (Interior / Exterior / Electrical) — Tailgate / Tailgate Switch / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Tailgate Trim Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Upper Tailgate Trim
1.
Remove the trim (A).

Body (Interior / Exterior / Electrical) — Tailgate / Tailgate Trim / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Tailgate / Tailgate Trim / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Tailgate / Tailgate Trim / Removal and Installation / Removal illustration

Side Tailgate Trim
1.
Remove the upper tailgate trim.
2.
Remove the trim (A) after removing the screw.

Body (Interior / Exterior / Electrical) — Tailgate / Tailgate Trim / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Tailgate / Tailgate Trim / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Tailgate / Tailgate Trim / Removal and Installation / Removal illustration

Lower Tailgate Trim
1.
Remove the side tailgate trim.
2.
Remove the power tailgate inner switch.
(Refer to Tailgate - "Tailgate Switch")
3.
Remove the tailgate hand grip (A).

Body (Interior / Exterior / Electrical) — Tailgate / Tailgate Trim / Removal and Installation / Removal illustration

4.
Remove the trim (A) after removing the screws.

Body (Interior / Exterior / Electrical) — Tailgate / Tailgate Trim / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Tailgate / Tailgate Trim / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Tailgate / Tailgate Trim / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Tailgate Weatherstrip Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Note
Be careful not to get sealant on the surface of the body.
1.
Remove the tailgate weatherstrip (A).

Body (Interior / Exterior / Electrical) — Tailgate / Tailgate Weatherstrip / Removal and Installation / Removal illustration

Note
When installing, check the center marking line (B).
Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Other information:

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Basic function

Kia EV6 Smart Cruise Control operates when the following conditions are satisfied: The gear selector is in D (Drive). Your Kia EV6 driving speed is within the applicable operating range: 5–120 mph (10–180 km/h) 0–120 mph (0–180 km/h) Electronic Stability Control (ESC) or Anti-lock Braking System (ABS) is turned ON and available.

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: A Guide to Storage, Transport and Disposal of Old Battery Systems

Used high voltage battery system storage, transportation, disposal guide • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training.

 
Copyright © 2026 Kia EV6 Manuals ⏱ 0.0191