Kia EV6: Sunroof / Sunroof Assembly Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Information
•
To remove the wide sunroof assembly, use the tools shown in the following figure.
[Tooling Diagram]

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Assembly / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Assembly / Removal and Installation / Removal illustration Square wire
Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Assembly / Removal and Installation / Removal illustration Insert-type wire grip

•
Insert and fix the square wire Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Assembly / Removal and Installation / Removal illustration into the hole of the wire grip Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Assembly / Removal and Installation / Removal illustration.
[Tooling Assembly Diagram]

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Assembly / Removal and Installation / Removal illustration

1.
Completely close the movable glass using the panorama sunroof switch.
2.
Remove the roof side molding.
(Refer to Body Side Molding - "Roof Side Molding")
3.
Remove the roof shark fin antenna.
(Refer to Infotainment system - "Antenna")
4.
Remove the moving glass.
(Refer to Sunroof - "Sunroof Glass")
5.
Remove the bolts (A).

Tightening torque :
7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Assembly / Removal and Installation / Removal illustration

6.
Remove the nuts (A).

Tightening torque :
7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Assembly / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Assembly / Removal and Installation / Removal illustration

7.
Cut off the sealant of forward edge area (B) by pulling the wire (A) to the left and right.

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Assembly / Removal and Installation / Removal illustration

Caution
•
Put on gloves to prevent hand injuries.
•
Be careful not to burn hands as the excessive heat may be generated while using the wire.
Note
•
Be careful as the wire may break when working.
•
When removing with a remover, use to wrap a protective tape around the tool to prevent the components from damages.
•
Be careful not to damage the body surface.
Information
When using the wires, work at least the two or more people together.
8.
Cut off the sealant on the front sealant area (A-A) while pulling the wire (B) to the left and right.

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Assembly / Removal and Installation / Removal illustration

Caution
•
Put on gloves to prevent hand injuries.
•
Be careful not to burn hands as the excessive heat may be generated while using the wire.
Note
•
Be careful as the wire may break when working.
•
When removing with a remover, use to wrap a protective tape around the tool to prevent the components from damages.
•
Be careful not to damage the body surface.
Information
When using the wires, work at least the two or more people together.
9.
Cut off the sealant on the side area (A-A), while pulling the wire (B) to the left and right.

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Assembly / Removal and Installation / Removal illustration

Caution
•
Put on gloves to prevent hand injuries.
•
Be careful not to burn hands as the excessive heat may be generated while using the wire.
Note
•
Be careful as the wire may break when working.
•
When removing with a remover, use to wrap a protective tape around the tool to prevent the components from damages.
•
Be careful not to damage the body surface.
Information
When using the wires, work at least the two or more people together.
10.
Cut off the sealant on the rear sealant area (A-A), while pulling the wire (B) to the left and right.

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Assembly / Removal and Installation / Removal illustration

Caution
•
Put on gloves to prevent hand injuries.
•
Be careful not to burn hands as the excessive heat may be generated while using the wire.
Note
•
Be careful as the wire may break when working.
•
When removing with a remover, use to wrap a protective tape around the tool to prevent the components from damages.
•
Be careful not to damage the body surface.
Information
When using the wires, work at least the two or more people together.
11.
Remove the wide sunroof assembly (A) after cutting the sealant on all sides.

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Assembly / Removal and Installation / Removal illustration

Note
Be careful not to damage the wide sunroof assembly when removing it.
12.
Cut off the remaining sealant (A) around the body panel by using the knife blade.

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Assembly / Removal and Installation / Removal illustration

Note
•
Be careful not to damage the body painting surface.
•
If the body painting surface is damaged, apply the repair paint or anti-corrosion agent.
Information
When cutting off the remaining sealant of the frame, leave a thickness of 2 mm on the adhesive side.
Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Clean the edges of the body panel and the sunroof assembly with alcohol, etc.
2.
Apply the body primer to the edge of the body panel and wide frame.
Note
•
Be careful not to touch the primed surface with your hands, as water leakage may occur after the sunroof assembly is installed.
•
Do not smear the primer-covered surface to any foreign materials.
3.
After applying the primer, apply the sealant around the body panel (A) by using a sealant gun.

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Assembly / Removal and Installation / Installation illustration

Note
If the sealant is over applied and the sealant is visible outside the vehicle, clean it with alcohol or a cleaning agent.
4.
Align to the centering device hole (A) on the body and carefully mount the wide sunroof on the body flange surface.

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Assembly / Removal and Installation / Installation illustration

5.
Install the wide sunroof and check the flush and gaps on each side. (flush and gap conditions need to be checked by vehicle type)

Item
Gap (mm)
Height (mm)
B-B
Windshield glass - Front glass
55 - 57
0.5 - 2.5
C-C
Moving glass - Body
56 - 58
-1 to 0.5

6.
Perform a water leak test at least 3 to 4 hours later after installing the sunroof assembly.
Note
Keep the water stream away from directly touching the newly installed adhesive surface and let the water fall on the side of the glass.
7.
When a leak occurs, apply the additional sealant to the leaking area.
Note
•
Allow the vehicle to stand flat for at least 4hours after installing the sunroof assembly.
•
If the vehicle needs to be used, drive slowly at least for 8 hours.
•
The driver should be careful to drive the vehicle aggressively or avoid uneven road driving for 2-3 days.
8.
Install in the reverse order of removal.

Other information:

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: A Guide to Storage, Transport and Disposal of Old Battery Systems

Used high voltage battery system storage, transportation, disposal guide • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training.

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Vehicle to load (V2L)

The Vehicle-to-Load (V2L) system in the Kia EV6 allows the high-voltage battery to supply AC electrical power for operating external electronic devices and household equipment. To activate the Kia EV6 V2L system, tap the V2L icon on the infotainment display.

Categories

 
Copyright © 2026 Kia EV6 Manuals � 0.0096