Kia EV6: Body (Interior / Exterior / Electrical) / Sunroof

Contents:

Components and Components Location

Component and Component Location
Wide Sunroof

Body (Interior / Exterior / Electrical) — Sunroof / Components and Components Location / Component and Component Location illustration

1. Front Glass
2. Front Glass Weatherstrip
3. Moving Glass
4. Sunroof Deflector
5. Sunroof Rail Assembly
6. Sunroof Drive Unit
7. Sunroof Roller Blind
8. Moving Glass Motor
9. Roller Blind Motor
10. Sunroof Cable
11. Sunroof Frame

Troubleshooting

Troubleshooting
Water Leaks
Components
Suspected Cause
Correction
Movable Glass
Defect of gap/flush
Adjustment
Weatherstrip
Incorrect installation and deformation
Replacement

Wind Noise
Components
Suspected Cause
Correction
Deflector
Deformation and separation
Replace or reinstall
Movable Glass
Defect of gap/flush
Adjust of gap/flush

Drive Noise
Components
Suspected Cause
Correction
Weatherstrip
Rubbing noise
apply the silicone oil
Hardware
Loose or unfastened
Hardware re-tighten
Cover / Trims
Interference noise (rattle/rubbing)
Attach the pad to the noise generating area.

Operation Noise
Components
Suspected Cause
Correction
Mechanism rail
Foreign matters in the mechanism rail
Cleaning the rail and apply the grease
Motor
Defective coupling of mechanism cable and motor pinion gear
Adjust or replace the motor position
Motor pinion gear worn out or broken
Replacement
Roller Blind
Noise inside the spring
Replacement

Malfunctions
Components
Suspected Cause
Correction
Mechanism rail
Increased operating load due to accumulation of foreign matters
1. Cleaning the rail and apply the grease
2. Adjust or replace the motor position
3. Replacement of mechanism rail
Motor
Defective coupling of mechanism cable and motor pinion gear
Adjust or replace the motor position
Motor position loss and sunroof switch one-touch operation failure due to discharge and replacement of battery and fuse
Motor Initialization
Roller Blind
Separation of the teflon guide
Replace or reinstall
Release of the spring tension
Replacement

On Vehicle Inspection

On Vehicle Inspection
Diagnostic with KDS
1.
The Roof Controller Module (RCM) can be quickly diagnosed for problems with KDS (Refer to "DTC guide").
(1)
Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS.
(Refer to DTC guide when fault code is found.)
Information
Refer to the KDS screen for operating conditions and details

Adjustment

Adjustment
Glass Adjustment
1.
Check the gap and flush of the front glass (A) and moving glass (B).
Front Glass - Moving Glass
Gap (mm)
Height (mm)

Body (Interior / Exterior / Electrical) — Sunroof / Adjustment illustration

5.6 - 5.8
-1 to 0

2.
Open the moving glass completely by pressing the wide sunroof switch.
3.
Remove the decoration cover (A).

Body (Interior / Exterior / Electrical) — Sunroof / Adjustment illustration

4.
If it is necessary to adjust the glass, slightly loosen the glass height adjustment screws (A) and tighten the screws.

Tightening torque :
3.9 - 5.9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)

[Inside]

Body (Interior / Exterior / Electrical) — Sunroof / Adjustment illustration

[Outside]

Body (Interior / Exterior / Electrical) — Sunroof / Adjustment illustration

Initialize Sunroof
If necessary, initialize the sunroof according to the initialization method.
The sunroof and roller blind are initialized using the sunroof switch.
1.
POWER ON or start the vehicle.
2.
Close the sunroof completely if opened
3.
Release the sunroof control lever.
4.
With the sunroof glass or roller blind closed, lightly press the switch forward until it moves once, then release your hand.
5.
Keep pressing the sunroof switch forward until the sunroof glass or roller blind opens and closes completely.
Note
•
Do not release the lever until the operation is completed.
•
If you release the switch during operation, it will try again from the beginning.
6.
Release the sunroof control lever after all operation has completed.
(The sunroof system been reset.)

Motor Removal and Installation

Replacement
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Remove the roof trim assembly.
(Refer to Roof Trim - "Roof Trim Assembly")
2.
Remove the sunroof motor (B) by removing the screws after disconnecting the connector (A).
[Roller Blind Motor]

Body (Interior / Exterior / Electrical) — Sunroof / Motor / Removal and Installation / Replacement illustration

[Moving Glass Motor]

Body (Interior / Exterior / Electrical) — Sunroof / Motor / Removal and Installation / Replacement illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.
2.
Perform the sunroof reset procedure.
(1)
POWER ON or start the vehicle.
(2)
Close the sunroof completely if opened
(3)
Release the sunroof control lever.
(4)
With the sunroof glass or roller blind closed, lightly press the switch forward until it moves once, then release your hand.
(5)
Keep pressing the sunroof switch forward until the sunroof glass or roller blind opens and closes completely.
Note
•
Do not release the lever until the operation is completed.
•
If you release the switch during operation, it will try again from the beginning.
(6)
Release the sunroof control lever after all operation has completed.
(The sunroof system been reset.)
3.
When replacing the roof control module (RCM) or motor, perform Over The Air (OTA) controller S/W update with KDS.
(Refer to Security & Vehicle Ignition System - "Over The Air (OTA)")

Sunroof Assembly Removal and Installation ➤

Sunroof Deflector Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Press the sunroof switch to fully open the sunroof glass.
2.
Separate the sunroof deflector (A) after removing the screws.

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Deflector / Removal and Installation / Removal illustration

3.
Remove the deflector.
(1)
Push the deflector mounting bracket (B) up in the direction of the arrow.
(2)
Remove the deflector (A) after pulling the deflector mounting bracket (B) in the direction of the arrow.

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Deflector / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Sunroof Glass Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Moving Glass
1.
Open the moving glass completely by pressing the wide sunroof switch.
2.
Remove the decoration cover (A).

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Glass / Removal and Installation / Removal illustration

3.
Remove the screws (A).

Tightening torque :
3.9 - 5.9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)

[Inside]

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Glass / Removal and Installation / Removal illustration

[Outside]

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Glass / Removal and Installation / Removal illustration

4.
Remove the glass (A).

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Glass / Removal and Installation / Removal illustration

Front Glass
Information
•
To remove the front glass, use the tools shown in the following figure.
[Tool Diagram]

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Glass / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Glass / Removal and Installation / Removal illustration Square wire
Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Glass / Removal and Installation / Removal illustration Insert-type wire grip

•
Insert and fix the square wire Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Glass / Removal and Installation / Removal illustration into the hole of the wire grip Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Glass / Removal and Installation / Removal illustration.
[Tool Assembly Diagram]

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Glass / Removal and Installation / Removal illustration

1.
Remove the roof side molding.
(Refer to Body Side Molding - "Roof Side Molding")
2.
Fully open the moving glass by pressing the wide sunroof switch.
3.
Cut the sealant by applying force in the direction of the arrow while pulling the square wire (A) to the left and right.

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Glass / Removal and Installation / Removal illustration

Note
•
Be careful as the wire may break when working.
•
Be careful not to damage the body surface.
•
When installing the windshield, if the length of the wire is longer, a lot of force is applied, so divide the sections Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Glass / Removal and Installation / Removal illustration and Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Glass / Removal and Installation / Removal illustration in half and cut the sealant.
4.
Remove the front glass carefully so that it does not get damaged.
Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Moving Glass
1.
Install in the reverse order of removal.
Front Glass
Information
To install the front glass, use the tools shown in the following figure.
[Tool Diagram]

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Glass / Removal and Installation / Installation illustration

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Glass / Removal and Installation / Installation illustration

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Glass / Removal and Installation / Installation illustration

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Glass / Removal and Installation / Installation illustration Sealant nozzle
Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Glass / Removal and Installation / Installation illustration Adhesive sealant for car glass
Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Glass / Removal and Installation / Installation illustration Sealant gun
Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Glass / Removal and Installation / Installation illustration Primer
Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Glass / Removal and Installation / Installation illustration Primer application brush

1.
Cut off the remaining sealant (A) around the wide sunroof frame windshield installing surface after using a knife blade.

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Glass / Removal and Installation / Installation illustration

Note
•
When cutting off the remaining sealant of the frame, leave it 2 mm thick on the working surface and cut.
•
Be careful not to damage the frame painted surface.
•
If the body painting surface is damaged, apply the repair paint or anti-corrosion agent.
2.
Wipe the edge of the wide sunroof frame and front glass with alcohol or blow with an air gun to clean it.
3.
Apply the primer around the wide sunroof frame.
4.
After applying the primer, apply the sealant (B) around the wide sunroof frame (A).

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Glass / Removal and Installation / Installation illustration

Note
Be careful not to leak or break the sealant when applying the sealant by using a sealant gun.
5.
Attach the front glass (A) to the wide sunroof frame.

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Glass / Removal and Installation / Installation illustration

6.
Install the front glass completely after checking the flush and gap.
Item
Gap [mm (in.)]
Flush [mm (in.)]
Windshield glass - Front glass
55 - 57 (2.16 - 2.24)
0.5 - 2.5 (0.2 - 1.0)
Front glass - Moving glass
56 - 58 (2.2 - 2.28)
0.5 - 1 (0.2 - 0.4)

[Windshield glass - Front glass]

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Glass / Removal and Installation / Installation illustration

[Front glass - Moving glass]

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Glass / Removal and Installation / Installation illustration

7.
Tape around the front glass so that it does not float.
Note
•
If the sealant is over-applied and the sealant is visible outside the vehicle, clean it with alcohol or a cleaning agent.
•
After installing the front glass, leave the vehicle on level ground at least for 4 hours.
•
If the vehicle needs to be used, drive slowly at least for 8 hours.
•
The driver should be careful to drive the vehicle aggressively or avoid uneven road driving for 2-3 days.

Sunroof Mechanism Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Remove the moving glass.
(Refer to Sunroof - "Sunroof Glass")
2.
Remove the moving glass motor and roller blind motor.
(Refer to Sunroof - "Motor")
3.
Disconnect the sunroof connector (A) after removing the fastener.

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Mechanism / Removal and Installation / Removal illustration

4.
Remove the sunroof mechanism after removing the screw (A).

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Mechanism / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Sunroof Roller Blind Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Remove the sunroof assembly.
(Refer to Sunroof - "Sunroof Assembly")
2.
Remove the roller blind bracket (A) after removing the screws.

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Roller Blind / Removal and Installation / Removal illustration

3.
Remove the roller blind bar.
(1)
Pull the roller blind bar (A) in the direction of the arrow Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Roller Blind / Removal and Installation / Removal illustration.
(2)
Separate the roller blind bar (A) by rotating it in the direction of the arrow Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Roller Blind / Removal and Installation / Removal illustration.

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Roller Blind / Removal and Installation / Removal illustration

4.
Remove the roller blind assembly (A) after removing the screws.

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Roller Blind / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Sunroof Switch Inspection

Inspection
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Remove the overhead console lamp.
(Refer to Light & Vision System - "Overhead Console Lamp")
2.
Check for continuity between the terminals.

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Switch / Inspection illustration


Open 1st
Open 2nd
Close 1st
Close 2nd
Tilt up
Tilt down
Signal
(Pin No.)
Manual open
Auto Open
Manual close
Auto Close
Signal A
(4)
O
O




Signal B
(5)

O
O
O


Signal C
(6)



O
O
O
Ground
(1)
O
O
O
O
O
O

Sunroof Weatherstrip Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Frame Weatherstrip
1.
Remove the moving glass.
(Refer to Sunroof - "Sunroof Glass")
2.
Remove the weatherstrip (A).

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Weatherstrip / Removal and Installation / Removal illustration

Front Glass Weatherstrip
1.
Fully open the moving glass.
2.
Remove the weatherstrip (A).

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Weatherstrip / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Frame Weatherstrip
1.
After removing the double-sided tape remaining on the wide sunroof frame, apply the primer [81685-3S000].
2.
After installing the frame weather strip, press the installing area.
3.
Install the moving glass.
(Refer to Sunroof - "Sunroof Glass")
Note
•
Place the air vent hole (A) in the rear part, and install it in the order of front part → side part → rear part.
•
Since the cross-section is not symmetrical, check the inside and outside and then install the frame weatherstrip.
•
Since the frame weatherstrip cannot be reused, it must be replaced with a new one when removed or replaced.

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Weatherstrip / Removal and Installation / Installation illustration

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Weatherstrip / Removal and Installation / Installation illustration

Front Glass Weatherstrip
1.
Install in the reverse order of removal.
Note
Be careful not to install the weatherstrip in reverse by referring to the cross-section below.

Body (Interior / Exterior / Electrical) — Sunroof / Sunroof Weatherstrip / Removal and Installation / Installation illustration

Other information:

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: How to connect adapter

Press the latch release button (1) on the CCS1 charging connector and insert the connector securely into the adapter (2) until it locks completely into place. Insert the CCS1 adapter into the NACS-equipped vehicle charging inlet and verify the charging connection status using the charging station display or charging system indicators.

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Manual Speed Limit Assist (MSLA)

Speed Limit indicator Displays the set speed The Kia EV6 Manual Speed Limit Assist (MSLA) system allows the driver to set a maximum preferred driving speed when it is not desirable to exceed a certain speed limit. If the Kia EV6 exceeds the preset speed limit, the Manual Speed Limit Assist system provides a warning by flashing the set speed indicator and sounding an audible chime until the vehicle speed returns within the selected limit.

 
Copyright © 2026 Kia EV6 Manuals ⏱ 0.0264