Kia EV6: Body (Interior / Exterior / Electrical) / Interior Trim

Contents:

Components and Components Location

Component and Component Location
Interior Trim

Body (Interior / Exterior / Electrical) — Interior Trim / Components and Components Location / Component and Component Location illustration

1. Cowl Side Trim
2. Front Door Scuff Trim
3. Rear Door Scuff Trim
4. Front Pillar Trim
5. Center Pillar Upper Trim
6. Front Seat Belt
6-a. 44.1 - 54.9 N·m (4.5 - 5.6 kgf·m, 32.5 - 40.5 lb·ft)
7. Center Pillar Lower Trim
8. Rear Transverse Trim
9. Rear Seat Cushion Assembly
10. Rear Seat Back Assembly [Driver's Side]
10-a. 16.7 - 25.5 N·m (1.7 - 2.6 kgf·m, 12.3 - 18.8 lb·ft)
11. Rear Seat Back Assembly [Passenger's Side]
11-a. 16.7 - 25.5 N·m (1.7 - 2.6 kgf·m, 12.3 - 18.8 lb·ft)
12. Luggage Side Trim

Center Pillar Trim Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Center Pillar Lower Trim
1.
Remove the front, rear door scuff trim.
(Refer to Interior Trim - "Door Scuff Trim")
2.
Slide the front seat to frontmost position.
3.
Remove the trim (A).

Body (Interior / Exterior / Electrical) — Interior Trim / Center Pillar Trim / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Interior Trim / Center Pillar Trim / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Interior Trim / Center Pillar Trim / Removal and Installation / Removal illustration

Center Pillar Upper Trim
1.
Remove the center pillar lower trim.
2.
Separate the seat belt (A) after removing the bolt.

Tightening torque :
44.1 - 54.9 N·m (4.5 - 5.6 kgf·m, 32.5 - 40.5 lb·ft)

Body (Interior / Exterior / Electrical) — Interior Trim / Center Pillar Trim / Removal and Installation / Removal illustration

3.
Remove the trim (A).

Body (Interior / Exterior / Electrical) — Interior Trim / Center Pillar Trim / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Interior Trim / Center Pillar Trim / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Interior Trim / Center Pillar Trim / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Cowl Side Trim Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Remove the front door scuff trim.
(Refer to Interior Trim - "Door Scuff Trim")
2.
Remove the hood latch release handle.
(Refer to Hood - "Hood Latch Release Handle")
3.
Remove the cowl side trim (A).

Body (Interior / Exterior / Electrical) — Interior Trim / Cowl Side Trim / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Interior Trim / Cowl Side Trim / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Interior Trim / Cowl Side Trim / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Door Scuff Trim Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Front Door Scuff Trim
1.
Remove the front door body side weatherstrip.
(Refer to Front Door - "Front Door Weatherstrip")
2.
Remove the trim (A).

Body (Interior / Exterior / Electrical) — Interior Trim / Door Scuff Trim / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Interior Trim / Door Scuff Trim / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Interior Trim / Door Scuff Trim / Removal and Installation / Removal illustration

Rear Door Scuff Trim
1.
Remove the rear seat cushion assembly.
(Refer to Rear Seat - "Rear Seat Assembly")
2.
Remove the rear door body side weatherstip.
(Refer to Rear Door - "Rear Door Weatherstrip")
3.
Remove the trim (A).

Body (Interior / Exterior / Electrical) — Interior Trim / Door Scuff Trim / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Floor Carpet Assembly Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Front Floor Carpet
1.
Remove the front seat assembly.
(Refer to Front Seat - "Front Seat Assembly")
2.
Remove the rear seat cushion and back assembly.
(Refer to Rear Seat - "Rear Seat Assembly")
3.
Remove the center pillar lower trim.
(Refer to Interior Trim - "Center Pillar Trim")
4.
Remove the cowl side trim
(Refer to Interior Trim - "Cowl Side Trim")
5.
Remove the floor console assembly.
(Refer to Floor Console - "Floor Console Assembly")
6.
Remove the luggage side trim.
(Refer to Luggage Trim - "Luggage Side Trim")
7.
Remove the seat belt anchor (A) after removing the bolt.

Tightening torque :
44.1 - 54.9 N·m (4.5 - 5.6 kgf·m, 32.5 - 40.5 lb·ft)

Body (Interior / Exterior / Electrical) — Interior Trim / Floor Carpet Assembly / Removal and Installation / Removal illustration

8.
Remove the rear seat belt anchor (A) after removing the bolt.

Tightening torque :
44.1 - 54.9 N·m (4.5 - 5.6 kgf·m, 32.5 - 40.5 lb·ft)

Body (Interior / Exterior / Electrical) — Interior Trim / Floor Carpet Assembly / Removal and Installation / Removal illustration

9.
Remove the rear duct cover (A) after removing the screws.
[Driver's Side]

Body (Interior / Exterior / Electrical) — Interior Trim / Floor Carpet Assembly / Removal and Installation / Removal illustration

[Passenger's Side]

Body (Interior / Exterior / Electrical) — Interior Trim / Floor Carpet Assembly / Removal and Installation / Removal illustration

10.
Remove the carpet (A).

Body (Interior / Exterior / Electrical) — Interior Trim / Floor Carpet Assembly / Removal and Installation / Removal illustration

11.
Remove the carpet pad (A).

Body (Interior / Exterior / Electrical) — Interior Trim / Floor Carpet Assembly / Removal and Installation / Removal illustration

Rear Floor Carpet
1.
Remove the luggage side trim.
(Refer to Luggage Trim - "Luggage Side Trim")
2.
Remove the carpet (A).

Body (Interior / Exterior / Electrical) — Interior Trim / Floor Carpet Assembly / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Front Pillar Trim Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Remove the front door body side weatherstrip.
(Refer to Front Door - "Front Door Weatherstrip")
2.
Remove the clip (A) by pushing in the direction of the arrow.

Body (Interior / Exterior / Electrical) — Interior Trim / Front Pillar Trim / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Interior Trim / Front Pillar Trim / Removal and Installation / Removal illustration

Front Pillar Trim Mounting Clip Separation (Play ▶)Body (Interior / Exterior / Electrical) — Interior Trim / Front Pillar Trim / Removal and Installation / Removal illustration
Notes When Refering Video
This video helps clearly identify areas that are hard to distinguish in manual images, such as component locations or assembly structures.
It also allows visual confirmation of areas that are difficult to see directly due to restricted visibility caused by surrounding components, from a technician’s perspective.
•
This video is created using common specifications and may differ from the actual vehicle.
•
The location and repair procedures of the parts may vary depending on vehicle model, model year, region, and specifications.
•
Check the KDS guide for detailed information on how to use the KDS.
•
Check the manual for detailed maintenance procedures.
•
Unauthorized reproduction, distribution, or sharing of this video is prohibited.
3.
Remove the front pillar trim (A).

Body (Interior / Exterior / Electrical) — Interior Trim / Front Pillar Trim / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Interior Trim / Front Pillar Trim / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Interior Trim / Front Pillar Trim / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Rear Pillar Trim Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Remove the luggage side trim.
(Refer to Luggage Trim - "Luggage Side Trim")
2.
Separate the seat belt (A) after removing the bolt.

Tightening torque :
44.1 - 54.9 N·m (4.5 - 5.6 kgf·m, 32.5 - 40.5 lb·ft)

Body (Interior / Exterior / Electrical) — Interior Trim / Rear Pillar Trim / Removal and Installation / Removal illustration

3.
Remove the rear pillar trim (A) after removing the bolts.

Tightening torque :
7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)

Body (Interior / Exterior / Electrical) — Interior Trim / Rear Pillar Trim / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Interior Trim / Rear Pillar Trim / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Interior Trim / Rear Pillar Trim / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Other information:

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Tilt and telescopic steering wheel

The Kia EV6 is equipped with a tilt and telescopic steering wheel system that allows the driver to customize the steering wheel position before driving for improved comfort, visibility, and control. You can also raise or reposition the steering wheel to create additional legroom when entering or exiting the Kia EV6, making everyday use more convenient and comfortable.

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: External air intake

When the Kia EV6 external fresh air mode is selected, outside air enters the cabin and is heated or cooled according to the selected climate settings. The indicator light switches OFF in this mode. Recirculated air intake In recirculation mode, air from inside the Kia EV6 cabin is drawn through the climate control system and heated or cooled according to the selected settings.

Contents

Categories

 
Copyright © 2026 Kia EV6 Manuals ⏱ 0.017