Kia EV6: Body (Interior / Exterior / Electrical) / Light & Vision System

Contents:

Specification

Specification
Item
Type
Headlamp
Low beam
LED
High Beam
LED
Turn signal lamp
LED
Position/DRL
LED
Rear Combination Lamp
Stop lamp
LED
Tail Lamp
LED
Turn signal lamp
LED
Room Lamp
LED
Turn signal lamp
LED
License Lamp
LED
Vanity Lamp
LED
High Mounted Stop Lamp
LED
Overhead Console Lamp
LED
Luggage Lamp
LED
Back-up Lamp
LED
Front Center Lamp
LED

Back-up Lamp Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Back-up Lamp
1.
Remove the rear bumper assembly.
(Refer to Front & Rear Bumper - "Rear Bumper Assembly")
2.
Disconnect the back up lamp connector (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / Back-up Lamp / Removal and Installation / Removal illustration

3.
Remove the back up lamp (A) after removing the screws.

Body (Interior / Exterior / Electrical) — Light & Vision System / Back-up Lamp / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Light & Vision System / Back-up Lamp / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Front Center Lamp Replacement

Replacement
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Remove the radiator upper grille.
(Refer to Front & Rear Bumper - "Front Bumper Assembly")
Note
The front center lamp cannot be replaced individually due to included in the radiator upper grille. If necessary, replace the radiator upper grille.

Hazard Switch Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Remove the crash pad air vent duct [Center].
(Refer to Crash Pad - "Crash Pad Air Vent")
2.
Disconnect the hazard switch connector (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / Hazard Switch / Removal and Installation / Removal illustration

3.
Remove the hazard switch (A) after removing the screws.

Body (Interior / Exterior / Electrical) — Light & Vision System / Hazard Switch / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Light & Vision System / Hazard Switch / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Headlamp Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Remove the front bumper assembly.
(Refer to Front & Rear Bumper - "Front Bumper Assembly")
2.
Disconnect the headlamp connector (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / Headlamp / Removal and Installation / Removal illustration

3.
Remove the lamp (C) after removing the bolts (A, B).

Tightening torque
A : 7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)
B : 28.4 - 34.3 N·m (2.9 - 3.5 kgf·m, 21.0 - 25.3 lb·ft)

Body (Interior / Exterior / Electrical) — Light & Vision System / Headlamp / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Headlamp Replacement

Replacement
Absorbent
1.
Remove the dust caps (A) after turning in the counterclockwise direction.

Body (Interior / Exterior / Electrical) — Light & Vision System / Headlamp / Replacement illustration

2.
Remove the absorbent bracket (A) after removing the screws.

Body (Interior / Exterior / Electrical) — Light & Vision System / Headlamp / Replacement illustration

3.
Replace the absorbent (A) by pulling it in the direction of the arrow.

Body (Interior / Exterior / Electrical) — Light & Vision System / Headlamp / Replacement illustration

Information
Fold the new absorbent material as the picture below.

Body (Interior / Exterior / Electrical) — Light & Vision System / Headlamp / Replacement illustration

Headlamp Adjustment

Adjustment
Headlamp Aiming
1.
Alternately turn the adjusting gear to adjust the headlamp aiming. If beam-setting equipment is not available, proceed as follows.
(1)
Inflate the tires to the specified pressure and remove any loads from the vehicle except the driver, spare tire, and tools.
(2)
The vehicle should be placed on a flat floor.
(3)
Check if there is something wrong with the suspension spring.
(4)
Clean the headlamp lens.
(5)
Draw vertical lines (Vertical lines passing through respective headlamp centers) and a horizontal line (Horizontal line passing through center of headlamps) on the screen.
(6)
With the headlamp and battery in normal condition, aim the headlamps so the brightest portion falls on the horizontal and vertical lines.
(7)
Accuracy check of measuring instruments.

Body (Interior / Exterior / Electrical) — Light & Vision System / Headlamp / Adjustment illustration

Information
A : Vertical (High/Low beam)
B : Horizontal (High/Low beam)
Headlamp Aiming Point
Aiming Point

Body (Interior / Exterior / Electrical) — Light & Vision System / Headlamp / Adjustment illustration

Body (Interior / Exterior / Electrical) — Light & Vision System / Headlamp / Adjustment illustration

Information
H1 : Height between the headlamps bulb center and ground (Low beam)
H2 : Height between the headlamps bulb center and ground (High beam)
W1 : Distance between the headlamp bulb center (Low beam)
W2 : Distance between the headlamp bulb center (High beam)
Vehicle Condition
H1
H2
W1
W2
Possible Cause
Empty
664
615
1,602
1,576
ALL DIM in mm (in.)
1 person on-board
654
605

1.
Draw a horizontal line at 0% from the headlamp ground clearance. [Visually Optically aimed using the Right side of the low beam (VOR) type only]

Body (Interior / Exterior / Electrical) — Light & Vision System / Headlamp / Adjustment illustration

2.
Turn the low beam on without driver aboard.

Body (Interior / Exterior / Electrical) — Light & Vision System / Headlamp / Adjustment illustration

Note
•
The low beam cut-off line should be projected as shown in the picture.
•
When aiming the low beam, vertical aiming should be adjusted after adjusting the horizontal aiming.
3.
Turn the high beam on without driver aboard.

A : 3 m / 6 m / 9 m
B (3% of A) : 90 mm / 180 mm / 270 mm
C (1% of A) : 30 mm / 60 mm / 90 mm
D (1.5% of A) : 45 mm / 90 mm / 180 mm

Body (Interior / Exterior / Electrical) — Light & Vision System / Headlamp / Adjustment illustration

Note
•
The hot zone should be projected in the allowable range shown in the picture.
•
If the HOT ZONE range of the high beam is out of regulation after adjusting the low beam, the product defect may be the cause. In such cases, exchange it for a new one after checking whether it is within the acceptable range.

High Mounted Stop Lamp Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
(1)
Open the front trunk (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / High Mounted Stop Lamp / Removal and Installation / Removal illustration

(2)
Open the auxiliary 12 V battery service cover (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / High Mounted Stop Lamp / Removal and Installation / Removal illustration

(3)
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).

Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)

Body (Interior / Exterior / Electrical) — Light & Vision System / High Mounted Stop Lamp / Removal and Installation / Removal illustration

(4)
Disconnect the service interlock connector (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / High Mounted Stop Lamp / Removal and Installation / Removal illustration

Warning
•
Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
•
When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
Note
The service interlock connector cannot be completely removed.

Body (Interior / Exterior / Electrical) — Light & Vision System / High Mounted Stop Lamp / Removal and Installation / Removal illustration

2.
Remove the tailgate side trim.
(Refer to Tailgate - "Tailgate Trim")
3.
Disconnect the high mounted stop lamp connector (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / High Mounted Stop Lamp / Removal and Installation / Removal illustration

4.
Remove the lamp (A) after removing the bolts.

Body (Interior / Exterior / Electrical) — Light & Vision System / High Mounted Stop Lamp / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Light & Vision System / High Mounted Stop Lamp / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

License Lamp Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
(1)
Open the front trunk (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / License Lamp / Removal and Installation / Removal illustration

(2)
Open the auxiliary 12 V battery service cover (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / License Lamp / Removal and Installation / Removal illustration

(3)
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).

Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)

Body (Interior / Exterior / Electrical) — Light & Vision System / License Lamp / Removal and Installation / Removal illustration

(4)
Disconnect the service interlock connector (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / License Lamp / Removal and Installation / Removal illustration

Warning
•
Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
•
When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
Note
The service interlock connector cannot be completely removed.

Body (Interior / Exterior / Electrical) — Light & Vision System / License Lamp / Removal and Installation / Removal illustration

2.
Remove the license lamp (A) by pulling it in the direction of the arrow.

Body (Interior / Exterior / Electrical) — Light & Vision System / License Lamp / Removal and Installation / Removal illustration

3.
Disconnect the license lamp connector (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / License Lamp / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Luggage Lamp Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
(1)
Open the front trunk (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / Luggage Lamp / Removal and Installation / Removal illustration

(2)
Open the auxiliary 12 V battery service cover (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / Luggage Lamp / Removal and Installation / Removal illustration

(3)
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).

Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)

Body (Interior / Exterior / Electrical) — Light & Vision System / Luggage Lamp / Removal and Installation / Removal illustration

(4)
Disconnect the service interlock connector (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / Luggage Lamp / Removal and Installation / Removal illustration

Warning
•
Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
•
When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
Note
The service interlock connector cannot be completely removed.

Body (Interior / Exterior / Electrical) — Light & Vision System / Luggage Lamp / Removal and Installation / Removal illustration

2.
Remove the luggage lamp (A) by pulling it in the direction of the arrow.

Body (Interior / Exterior / Electrical) — Light & Vision System / Luggage Lamp / Removal and Installation / Removal illustration

3.
Disconnect the lamp connector (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / Luggage Lamp / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Mood Lamp Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Mood Lamp Unit
1.
Remove the crash pad assembly.
(Refer to Crash Pad - "Crash Pad Assembly")
2.
Disconnect the mood lamp unit connector (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / Mood Lamp / Removal and Installation / Removal illustration

3.
Remove the unit (A) after removing the nut.

Tightening torque :
3.9 - 7.8 N·m (0.4 - 0.8 kgf·m, 2.9 - 5.8 lb·ft)

Body (Interior / Exterior / Electrical) — Light & Vision System / Mood Lamp / Removal and Installation / Removal illustration

Mood Lamp [Front Door]
1.
Remove the front door trim.
(Refer to Front Door - "Front Door Trim")
2.
Remove the mood lamp.
(1)
Remove the mood lamp (A) after removing the screws.
(2)
Disconnect the mood lamp connectors (B).

Body (Interior / Exterior / Electrical) — Light & Vision System / Mood Lamp / Removal and Installation / Removal illustration

Mood Lamp [Rear Door]
1.
Remove the rear door trim.
(Refer to Rear Door - "Rear Door Trim")
2.
Remove the mood lamp.
(1)
Remove the mood lamp (A) after removing the screws.
(2)
Disconnect the mood lamp connectors (B).

Body (Interior / Exterior / Electrical) — Light & Vision System / Mood Lamp / Removal and Installation / Removal illustration

Mood Lamp [Crash Pad]
1.
Remove the crash pad center garnish [RH].
(Refer to Crash Pad - " Crash pad Garnish")
2.
Remove the mood lamp.
(1)
Remove the mood lamp (A) after removing the screws.
(2)
Disconnect the mood lamp connector (B).

Body (Interior / Exterior / Electrical) — Light & Vision System / Mood Lamp / Removal and Installation / Removal illustration

Mood Lamp [Floor Console]
1.
Remove the console upper cover.
(Refer to Floor Console - "Console Upper Cover”)
2.
Remove the mood lamp.
(1)
Remove the mood lamp (A) after removing the screws.
(2)
Disconnect the mood lamp connectors (B).

Body (Interior / Exterior / Electrical) — Light & Vision System / Mood Lamp / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Overhead Console Lamp Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
(1)
Open the front trunk (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / Overhead Console Lamp / Removal and Installation / Removal illustration

(2)
Open the auxiliary 12 V battery service cover (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / Overhead Console Lamp / Removal and Installation / Removal illustration

(3)
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).

Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)

Body (Interior / Exterior / Electrical) — Light & Vision System / Overhead Console Lamp / Removal and Installation / Removal illustration

(4)
Disconnect the service interlock connector (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / Overhead Console Lamp / Removal and Installation / Removal illustration

Warning
•
Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
•
When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
Note
The service interlock connector cannot be completely removed.

Body (Interior / Exterior / Electrical) — Light & Vision System / Overhead Console Lamp / Removal and Installation / Removal illustration

2.
Remove the overhead console lamp (A) by pulling it in the direction of the arrow.

Body (Interior / Exterior / Electrical) — Light & Vision System / Overhead Console Lamp / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Light & Vision System / Overhead Console Lamp / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Light & Vision System / Overhead Console Lamp / Removal and Installation / Removal illustration

3.
Disconnect the lamp connector (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / Overhead Console Lamp / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Rear Combination Lamp Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Outside Rear Combination Lamp
1.
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
(1)
Open the front trunk (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / Rear Combination Lamp / Removal and Installation / Removal illustration

(2)
Open the auxiliary 12 V battery service cover (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / Rear Combination Lamp / Removal and Installation / Removal illustration

(3)
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).

Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)

Body (Interior / Exterior / Electrical) — Light & Vision System / Rear Combination Lamp / Removal and Installation / Removal illustration

(4)
Disconnect the service interlock connector (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / Rear Combination Lamp / Removal and Installation / Removal illustration

Warning
•
Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
•
When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
Note
The service interlock connector cannot be completely removed.

Body (Interior / Exterior / Electrical) — Light & Vision System / Rear Combination Lamp / Removal and Installation / Removal illustration

2.
Remove the luggage side trim service cover (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / Rear Combination Lamp / Removal and Installation / Removal illustration

3.
Disconnect the lamp connectors (A).
[Driver's Side]

Body (Interior / Exterior / Electrical) — Light & Vision System / Rear Combination Lamp / Removal and Installation / Removal illustration

[Passenger's Side]

Body (Interior / Exterior / Electrical) — Light & Vision System / Rear Combination Lamp / Removal and Installation / Removal illustration

4.
Remove the nuts (A).
[Driver's Side]

Body (Interior / Exterior / Electrical) — Light & Vision System / Rear Combination Lamp / Removal and Installation / Removal illustration

[Passenger's Side]

Body (Interior / Exterior / Electrical) — Light & Vision System / Rear Combination Lamp / Removal and Installation / Removal illustration

5.
Remove the screws (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / Rear Combination Lamp / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Light & Vision System / Rear Combination Lamp / Removal and Installation / Removal illustration

6.
Remove the lamp (A) by pulling it in the direction of the arrow.

Body (Interior / Exterior / Electrical) — Light & Vision System / Rear Combination Lamp / Removal and Installation / Removal illustration

Center Rear Combination Lamp
1.
Remove the tailgate garnish.
(Refer to Body Side Molding - "Tailgate Garnish")
2.
Remove the lower tailgate trim.
(Refer to Tailgate - "Tailgate Trim")
3.
Disconnect the connector (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / Rear Combination Lamp / Removal and Installation / Removal illustration

4.
Remove the lamp (A) by pulling it in the direction of the arrow after removing the nuts.

Body (Interior / Exterior / Electrical) — Light & Vision System / Rear Combination Lamp / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Light & Vision System / Rear Combination Lamp / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Light & Vision System / Rear Combination Lamp / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Rear Combination Lamp Disassembly and Reassembly

Disassembly
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Outside Rear Combination Lamp [Driver's Side]
1.
Remove the outside rear combination lamp.
(Refer to Rear Combination Lamp - "Removal and Installation")
2.
Remove the stop lamp & tail lamp (A) after removing the screws.

Body (Interior / Exterior / Electrical) — Light & Vision System / Rear Combination Lamp / Disassembly and Reassembly / Disassembly illustration

Body (Interior / Exterior / Electrical) — Light & Vision System / Rear Combination Lamp / Disassembly and Reassembly / Disassembly illustration

3.
Remove the side repeater lamp (A) after removing the screws.

Body (Interior / Exterior / Electrical) — Light & Vision System / Rear Combination Lamp / Disassembly and Reassembly / Disassembly illustration

Body (Interior / Exterior / Electrical) — Light & Vision System / Rear Combination Lamp / Disassembly and Reassembly / Disassembly illustration

Outside Rear Combination Lamp [Passenger's Side]
1.
Remove the outside rear combination lamp.
(Refer to Rear Combination Lamp - "Removal and Installation")
2.
Remove the flange cover (A) after removing the screws.

Body (Interior / Exterior / Electrical) — Light & Vision System / Rear Combination Lamp / Disassembly and Reassembly / Disassembly illustration

3.
Disconnect the charge door control unit connector (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / Rear Combination Lamp / Disassembly and Reassembly / Disassembly illustration

4.
Remove the stop lamp & tail lamp (A) after removing the screws.

Body (Interior / Exterior / Electrical) — Light & Vision System / Rear Combination Lamp / Disassembly and Reassembly / Disassembly illustration

Body (Interior / Exterior / Electrical) — Light & Vision System / Rear Combination Lamp / Disassembly and Reassembly / Disassembly illustration

5.
Remove the turn signal lamp (A) by removing the screws.

Body (Interior / Exterior / Electrical) — Light & Vision System / Rear Combination Lamp / Disassembly and Reassembly / Disassembly illustration

Body (Interior / Exterior / Electrical) — Light & Vision System / Rear Combination Lamp / Disassembly and Reassembly / Disassembly illustration

Reassembly
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Reassemble in the reverse order of disassembly.

Room Lamp Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
(1)
Open the front trunk (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / Room Lamp / Removal and Installation / Removal illustration

(2)
Open the auxiliary 12 V battery service cover (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / Room Lamp / Removal and Installation / Removal illustration

(3)
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).

Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)

Body (Interior / Exterior / Electrical) — Light & Vision System / Room Lamp / Removal and Installation / Removal illustration

(4)
Disconnect the service interlock connector (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / Room Lamp / Removal and Installation / Removal illustration

Warning
•
Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
•
When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
Note
The service interlock connector cannot be completely removed.

Body (Interior / Exterior / Electrical) — Light & Vision System / Room Lamp / Removal and Installation / Removal illustration

2.
Remove the room lamp (A) by pulling it in the direction of the arrow.

Body (Interior / Exterior / Electrical) — Light & Vision System / Room Lamp / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Light & Vision System / Room Lamp / Removal and Installation / Removal illustration

3.
Disconnect the lamp connector (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / Room Lamp / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Turn Signal Lamp Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Remove the scalp.
(Refer to Mirror - "Outside Mirror")
2.
Disconnect the side repeater lamp connector (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / Turn Signal Lamp / Removal and Installation / Removal illustration

3.
Remove the lamp (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / Turn Signal Lamp / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Vanity Lamp Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
(1)
Open the front trunk (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / Vanity Lamp / Removal and Installation / Removal illustration

(2)
Open the auxiliary 12 V battery service cover (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / Vanity Lamp / Removal and Installation / Removal illustration

(3)
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).

Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)

Body (Interior / Exterior / Electrical) — Light & Vision System / Vanity Lamp / Removal and Installation / Removal illustration

(4)
Disconnect the service interlock connector (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / Vanity Lamp / Removal and Installation / Removal illustration

Warning
•
Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
•
When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
Note
The service interlock connector cannot be completely removed.

Body (Interior / Exterior / Electrical) — Light & Vision System / Vanity Lamp / Removal and Installation / Removal illustration

2.
Remove the vanity lamp (A) by pulling it in the direction of the arrow.

Body (Interior / Exterior / Electrical) — Light & Vision System / Vanity Lamp / Removal and Installation / Removal illustration

3.
Disconnect the lamp connector (A).

Body (Interior / Exterior / Electrical) — Light & Vision System / Vanity Lamp / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Other information:

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Position & Taillamp

When the lighting control switch of the Kia EV6 is placed in the parking light position, the taillights, license plate lights, position lamps, and instrument panel illumination automatically turn ON. This lighting mode improves vehicle visibility during nighttime parking, low-light driving conditions, or situations where full headlamp illumination is not required.

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Windows

The Kia EV6 is equipped with advanced power windows that can be conveniently operated using dedicated control switches located on each door panel. Power window lock button Rear door (left) power window switch Rear door (right) power window switch Driver’s door power window switch Front passenger’s door power window switch NOTE In freezing or wet weather conditions, the Kia EV6 power windows may operate slower than normal or temporarily stop functioning because of ice accumulation.

 
Copyright © 2026 Kia EV6 Manuals ⏱ 0.0174