Kia EV6: Maintenance / Power Train

Contents:

Reduction Gear Oil Repair procedures - Front Motor

Replacement
Warning
•
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. It is because that lack of knowledge of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
•
When working on high voltage system or related system, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
Note
When checking the reduction gear oil level, be careful not to allow foreign substance (like dust) to enter through the filler hole.
1.
Remove the front under cover.
(Refer to Front Motor and Reduction Gear System - "Front Under Cover")
2.
Prepare a clean 5 ℓ beaker (A) to measure the amount of oil.

Maintenance — Power Train / Reduction Gear Oil / Repair procedures - Front Motor / Replacement illustration

3.
Remove the drain plug (A) and drain oil, and then reinstall the drain plug.

Tightening torque :
44.1 - 58.8 N·m (4.5 - 6.0 kgf·m, 32.5 - 43.4 lb·ft)

Maintenance — Power Train / Reduction Gear Oil / Repair procedures - Front Motor / Replacement illustration

Note
The existing drain plug gasket (A) must be replaced with a new one (do not reuse).

Maintenance — Power Train / Reduction Gear Oil / Repair procedures - Front Motor / Replacement illustration

4.
Remove the front reduction gear cover fastener (A).

Maintenance — Power Train / Reduction Gear Oil / Repair procedures - Front Motor / Replacement illustration

5.
Remove the filler plug (A).

Maintenance — Power Train / Reduction Gear Oil / Repair procedures - Front Motor / Replacement illustration

6.
Fill the specified oil through the filler plug hole as much as it has been drained.

Recommended : Kia genuine ATF SP4M-1

7.
Install the filler plug (A).

Tightening torque :
44.1 - 58.8 N·m (4.5 - 6.0 kgf·m, 32.5 - 43.4 lb·ft)

Maintenance — Power Train / Reduction Gear Oil / Repair procedures - Front Motor / Replacement illustration

Note
The existing filler plug gasket (A) must be replaced with a new one (do not reuse).

Maintenance — Power Train / Reduction Gear Oil / Repair procedures - Front Motor / Replacement illustration

8.
Install the front reduction gear cover fastener (A).

Maintenance — Power Train / Reduction Gear Oil / Repair procedures - Front Motor / Replacement illustration

9.
Install the front under cover.
(Refer to Front Motor and Reduction Gear System - "Front Under Cover")

Reduction Gear Oil Repair procedures - Rear Motor

Replacement
Warning
•
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. It is because that lack of knowledge of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
•
When working on high voltage system or related system, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
Note
When checking the reduction gear oil level, be careful not to allow foreign substance (like dust) to enter through the filler hole.
1.
Remove the rear under cover.
(Refer to Rear Motor and Reduction Gear System - "Rear Under Cover")
2.
Prepare a clean 5 ℓ beaker (A) to measure the amount of oil.

Maintenance — Power Train / Reduction Gear Oil / Repair procedures - Rear Motor / Replacement illustration

3.
Remove the drain plug (A) and drain oil, and then reinstall the drain plug.

Tightening torque :
44.1 - 58.8 N·m (4.5 - 6.0 kgf·m, 32.5 - 43.4 lb·ft)

Maintenance — Power Train / Reduction Gear Oil / Repair procedures - Rear Motor / Replacement illustration

Note
The existing drain plug gasket (A) must be replaced with a new one (do not reuse).

Maintenance — Power Train / Reduction Gear Oil / Repair procedures - Rear Motor / Replacement illustration

4.
Remove the filler plug (A).

Maintenance — Power Train / Reduction Gear Oil / Repair procedures - Rear Motor / Replacement illustration

5.
Fill the specified oil through the filler plug hole as much as it has been drained.

Recommended : Kia genuine ATF SP4M-1

6.
Install the filler plug (A).

Tightening torque :
44.1 - 58.8 N·m (4.5 - 6.0 kgf·m, 32.5 - 43.4 lb·ft)

Maintenance — Power Train / Reduction Gear Oil / Repair procedures - Rear Motor / Replacement illustration

Note
The existing filler plug gasket (A) must be replaced with a new one (do not reuse).

Maintenance — Power Train / Reduction Gear Oil / Repair procedures - Rear Motor / Replacement illustration

7.
Install the rear under cover.
(Refer to Rear Motor and Reduction Gear System - "Rear Under Cover")

Coolant Drain

Special Service Tool
Tool Name / Number
Illustration
Description
Coolant refiller & suction tool
0K253 - J2300

Maintenance — Power Train / Coolant / Drain / Special Service Tool illustration

Used to drain and fill the coolant for EV
Cap adapter
0K253 - J2320

Maintenance — Power Train / Coolant / Drain / Special Service Tool illustration

Used to drain and fill the coolant for EV

SST (0K253 - J2300) Detail Name

Maintenance — Power Train / Coolant / Drain / Special Service Tool illustration

Maintenance — Power Train / Coolant / Drain / Special Service Tool illustration

1. Pressure Valve
2. Suction Valve
3. Vacuum Valve 1
4. Vacuum Valve 2
5. Coolant Injection
6. Vacuum Valve
7. Regulator Pressure Gauge
8. Pressure Gauge
9. Vacuum Gauge
10. Air Pressurization Valve
11. Vacuum Outlet Valve
12. Air Hose Inlet Valve
13. Regulator Adjusting Knob

Drain
Warning
•
When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
•
When working a high voltage system, the technician must be recognized and observe "General Safety Information and Caution". If do not follow, serious accidents like electric shock and short circuit are caused.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Disconnect the battery negative ( - ) terminal and the high voltage service interlock connector.
(Refer to Battery Control System - "Battery (12 V)")
(Refer to Battery Control System - "Battery (12 V)" - 4WD)
2.
Open the reservoir tank cap (A).

Maintenance — Power Train / Coolant / Drain illustration

3.
Install the cap adapter (0K253 - J2320).

Maintenance — Power Train / Coolant / Drain illustration

4.
Install the radiator cap connection hose (A) to the radiator cap adapter (B).

Maintenance — Power Train / Coolant / Drain illustration

5.
Connect the radiator cap connection hose (A) to the air pressurization valve of SST (0K253 - J2300).

Maintenance — Power Train / Coolant / Drain illustration

6.
Install the air hose (A) to the air inlet valve of SST (0K253 - J2300).

Maintenance — Power Train / Coolant / Drain illustration

Note
Make sure all valves are closed.

Maintenance — Power Train / Coolant / Drain illustration

7.
Turn the regulator adjusting knob (A) to set pressure gauge (B) to 0.2 Mpa.

Maintenance — Power Train / Coolant / Drain illustration

Note
After adjusting the pressure, close the regulator adjustment knob.
8.
Remove the front under cover.
(Refer to Motor & Reduction Gear System - "Front Under Cover")
9.
Release the quick connector, and then disconnect the high voltage battery EWP cooling hose (A).
[2WD]

Maintenance — Power Train / Coolant / Drain illustration

[4WD]

Maintenance — Power Train / Coolant / Drain illustration

10.
Install the coolant drain adapter and hose (A) to the battery EWP and EWP cooling hose.
[2WD]

Maintenance — Power Train / Coolant / Drain illustration

[4WD]

Maintenance — Power Train / Coolant / Drain illustration

11.
Put the opposite of the coolant drain adapter and hose (A) to a bucket (B).

Maintenance — Power Train / Coolant / Drain illustration

12.
Turn the pressure valve (A) the direction of the arrow to drain coolant.

Maintenance — Power Train / Coolant / Drain illustration

Note
Make sure that the valves other than the pressure valve (A) are closed.
13.
Close the pressure valve after draining coolant, and then install the high voltage battery EWP coolant hose (A).
[2WD]

Maintenance — Power Train / Coolant / Drain illustration

[4WD]

Maintenance — Power Train / Coolant / Drain illustration

14.
Remove the rear under cover.
(Refer to Motor and Reduction Gear System - "Rear Under Cover")
15.
Disconnect the cooling hose (A) after releasing the quick connector.

Maintenance — Power Train / Coolant / Drain illustration

16.
Install the coolant drain adapter and hose (A) to the cooling hose.

Maintenance — Power Train / Coolant / Drain illustration

17.
Put the opposite of the coolant drain adapter and hose (A) to a bucket (B).

Maintenance — Power Train / Coolant / Drain illustration

18.
Turn the pressure valve (A) the direction of the arrow to drain coolant.

Maintenance — Power Train / Coolant / Drain illustration

Note
Make sure that the valves other than the pressure valve (A) are closed.
19.
Close the pressure valve after draining coolant, and then install the cooling hose (A).

Maintenance — Power Train / Coolant / Drain illustration

20.
Separate the radiator cap connection hose (A) to the air pressurization valve.

Maintenance — Power Train / Coolant / Drain illustration

Coolant Refilling

Special Service Tool
Tool Name / Number
Illustration
Description
Coolant refiller & suction tool
0K253 - J2300

Maintenance — Power Train / Coolant / Refilling / Special Service Tool illustration

Used to drain and fill the coolant for EV
Cap adapter
0K253 - J2320

Maintenance — Power Train / Coolant / Refilling / Special Service Tool illustration

Used to drain and fill the coolant for EV

SST (0K253 - J2300) Detail Name

Maintenance — Power Train / Coolant / Refilling / Special Service Tool illustration

Maintenance — Power Train / Coolant / Refilling / Special Service Tool illustration

1. Pressure Valve
2. Suction Valve
3. Vacuum Valve 1
4. Vacuum Valve 2
5. Coolant Injection
6. Vacuum Valve
7. Regulator Pressure Gauge
8. Pressure Gauge
9. Vacuum Gauge
10. Air Pressurization Valve
11. Vacuum Outlet Valve
12. Air Hose Inlet Valve
13. Regulator Adjusting Knob

Refilling
Note
•
Be careful not to spill coolant on the electric devices when replacing the coolant.
•
Use genuine antifreeze/coolant.
•
To prevent corrosion, the concentration of coolant should be maintained at a minimum of 45%. If the coolant concentration is less than 45%, there may be a risk of corrosion or freezing.
•
It is not recommended if the concentration of the coolant exceeds 60%, as the cooling effect may be reduced.
•
Do not mix antifreeze/coolant from different brands.
•
Do not add any anti-rust.
1.
Drain the coolant.
(Refer to Coolant - "Drain")
2.
Connect the radiator cap connection hose (A) to the vacuum valve of SST (0K253 - J2300).

Maintenance — Power Train / Coolant / Refilling illustration

3.
Open the vacuum valve (A) in the direction of the arrow, and then close when the vacuum gauge (B) reaches the green area (C).

Maintenance — Power Train / Coolant / Refilling illustration

Note
Make sure that the valves other than the vacuum valve (A) are closed.
4.
Connect the coolant suction hose (A) to SST (0K253 - J2300) coolant filler valve and place the opposite hose in the bucket (B) containing new coolant.

Maintenance — Power Train / Coolant / Refilling illustration

5.
Turn the suction valve (A) in the direction of the arrow to fill new coolant, and then close it when the vacuum gauge reaches to '0'.

Maintenance — Power Train / Coolant / Refilling illustration

Note
Check that the valve except the suction valve (A) is locked.
6.
Remove the cap adapter (0K253 - J2320).

Maintenance — Power Train / Coolant / Refilling illustration

7.
Perform the order below with the KDS.
(S/W Management → Vehicle Control → Electric Water Pump Control)
Note
Charge the auxiliary 12 V battery during performing "Electric Water Pump Control" to prevent battery drain.
Information
When driving EWP, operate within 10 minutes.
8.
When the EWP operates and coolant circulates, refill coolant so that the coolant level is kept between "MAX" and "MIN" level.

Maintenance — Power Train / Coolant / Refilling illustration

Note
Friction may damage the bearing if the EWP is operated without coolant.
9.
When the operational sound volume of the EWP becomes small and when no air bubbles can be seen in the reservoir tank, bleeding of the coolant system is completed.
Note
•
After air bleeding is completed make sure that coolant in the reservoir tank flow without air bubble during the EWP actuation.
•
If the coolant flow is not seen or air bubbles are still seen, repeat steps 7 to 8.
10.
Perform the order below with the KDS.
(Actuation Test → Vehicle Control → Battery EWP Operation Mode for Degassing and Circulation)
Note
Charge the auxiliary 12 V battery during performing "Battery Electric Water Pump Control" to prevent battery drain.
Information
When driving EWP, operate within 10 minutes.
11.
When the battery EWP operates and coolant circulates, refill coolant so that the coolant level is kept between "MAX" and "MIN" level.

Maintenance — Power Train / Coolant / Refilling illustration

Note
Friction may damage the bearing if the EWP is operated without coolant.
12.
When the operational sound volume of the EWP becomes small and when no air bubbles can be seen in the reservoir tank, bleeding of the coolant system is completed.
Note
•
After air bleeding is completed make sure that coolant in the reservoir flow without air bubble during the EWP actuation.
•
If the coolant flow is not seen or air bubbles are still seen, repeat steps 10 to 11.
13.
After air bleeding is completed, refill the coolant to the MAX level and install the reservoir cap.

Maintenance — Power Train / Coolant / Refilling illustration

14.
Check the coolant for leakage.
Note
The cooling system air bleeding and coolant injection are performed perfectly when the coolant is completely cooled. Check the coolant level of the reservoir tank for 2 - 3 days after flushing the coolant.
15.
Install the front under cover.
(Refer to Motor & Reduction Gear System - "Front Under Cover")
16.
Install the rear under cover.
(Refer to Motor and Reduction Gear System - "Rear Under Cover")

High Voltage Battery Coolant Drain

Special Service Tool
Tool Name / Number
Illustration
Description
Coolant refiller & suction tool
0K253 - J2300

Maintenance — Power Train / High Voltage Battery Coolant / Drain / Special Service Tool illustration

Used to drain and fill the coolant for EV
Cap adapter
0K253 - J2320

Maintenance — Power Train / High Voltage Battery Coolant / Drain / Special Service Tool illustration

Used to drain and fill the coolant for EV

SST (0K253 - J2300) Detail Name

Maintenance — Power Train / High Voltage Battery Coolant / Drain / Special Service Tool illustration

Maintenance — Power Train / High Voltage Battery Coolant / Drain / Special Service Tool illustration

1. Pressure Valve
2. Suction Valve
3. Vacuum Valve 1
4. Vacuum Valve 2
5. Coolant Injection
6. Vacuum Valve
7. Regulator Pressure Gauge
8. Pressure Gauge
9. Vacuum Gauge
10. Air Pressurization Valve
11. Vacuum Outlet Valve
12. Air Hose Inlet Valve
13. Regulator Adjusting Knob

Drain
Warning
•
When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
•
When working a high voltage system, the technician must be recognized and observe "General Safety Information and Caution". If do not follow, serious accidents like electric shock and short circuit are caused.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Disconnect the battery negative ( - ) terminal and the high voltage service interlock connector.
(Refer to Battery Control System - "Battery (12 V)")
(Refer to Battery Control System - "Battery (12 V)" - 4WD)
2.
Open the reservoir tank cap (A).

Maintenance — Power Train / High Voltage Battery Coolant / Drain illustration

3.
Install the cap adapter (0K253 - J2320).

Maintenance — Power Train / High Voltage Battery Coolant / Drain illustration

4.
Install the radiator cap connection hose (A) to the radiator cap adapter (B).

Maintenance — Power Train / High Voltage Battery Coolant / Drain illustration

5.
Connect the radiator cap connection hose (A) to the air pressurization valve of SST (0K253 - J2300).

Maintenance — Power Train / High Voltage Battery Coolant / Drain illustration

6.
Install the air hose (A) to the air inlet valve of SST (0K253 - J2300).

Maintenance — Power Train / High Voltage Battery Coolant / Drain illustration

Note
Make sure all valves are closed.

Maintenance — Power Train / High Voltage Battery Coolant / Drain illustration

7.
Turn the regulator adjusting knob (A) to set pressure gauge (B) to 0.2 Mpa.

Maintenance — Power Train / High Voltage Battery Coolant / Drain illustration

Note
After adjusting the pressure, close the regulator adjustment knob.
8.
Remove the front under cover.
(Refer to Motor & Reduction Gear System - "Front Under Cover")
9.
Release the quick connector, and then disconnect the high voltage battery EWP cooling hose (A).
[2WD]

Maintenance — Power Train / High Voltage Battery Coolant / Drain illustration

[4WD]

Maintenance — Power Train / High Voltage Battery Coolant / Drain illustration

10.
Install the coolant drain adapter and hose (A) to the battery EWP and EWP cooling hose.
[2WD]

Maintenance — Power Train / High Voltage Battery Coolant / Drain illustration

[4WD]

Maintenance — Power Train / High Voltage Battery Coolant / Drain illustration

11.
Put the opposite of the coolant drain adapter and hose (A) to a bucket (B).

Maintenance — Power Train / High Voltage Battery Coolant / Drain illustration

12.
Turn the pressure valve (A) the direction of the arrow to drain coolant.

Maintenance — Power Train / High Voltage Battery Coolant / Drain illustration

Note
Make sure that the valves other than the pressure valve (A) are closed.
13.
Close the pressure valve after draining coolant, and then install the high voltage battery EWP coolant hose (A).
[2WD]

Maintenance — Power Train / High Voltage Battery Coolant / Drain illustration

[4WD]

Maintenance — Power Train / High Voltage Battery Coolant / Drain illustration

14.
Separate the radiator cap connection hose (A) to the air pressurization valve.

Maintenance — Power Train / High Voltage Battery Coolant / Drain illustration

High Voltage Battery Coolant Refilling

Special Service Tool
Tool Name / Number
Illustration
Description
Coolant refiller & suction tool
0K253 - J2300

Maintenance — Power Train / High Voltage Battery Coolant / Refilling / Special Service Tool illustration

Used to drain and fill the coolant for EV
Cap adapter
0K253 - J2320

Maintenance — Power Train / High Voltage Battery Coolant / Refilling / Special Service Tool illustration

Used to drain and fill the coolant for EV

SST (0K253 - J2300) Detail Name

Maintenance — Power Train / High Voltage Battery Coolant / Refilling / Special Service Tool illustration

Maintenance — Power Train / High Voltage Battery Coolant / Refilling / Special Service Tool illustration

1. Pressure Valve
2. Suction Valve
3. Vacuum Valve 1
4. Vacuum Valve 2
5. Coolant Injection
6. Vacuum Valve
7. Regulator Pressure Gauge
8. Pressure Gauge
9. Vacuum Gauge
10. Air Pressurization Valve
11. Vacuum Outlet Valve
12. Air Hose Inlet Valve
13. Regulator Adjusting Knob

Refilling
Note
•
Be careful not to spill coolant on the electric devices when replacing the coolant.
•
Use genuine antifreeze/coolant.
•
To prevent corrosion, the concentration of coolant should be maintained at a minimum of 45%. If the coolant concentration is less than 45%, there may be a risk of corrosion or freezing.
•
It is not recommended if the concentration of the coolant exceeds 60%, as the cooling effect may be reduced.
•
Do not mix antifreeze/coolant from different brands.
•
Do not add any anti-rust.
1.
Drain the high voltage battery coolant.
(Refer to High Voltage Battery Coolant - "Drain")
2.
Connect the radiator cap connection hose (A) to the vacuum valve of SST (0K253 - J2300).

Maintenance — Power Train / High Voltage Battery Coolant / Refilling illustration

3.
Open the vacuum valve (A) in the direction of the arrow, and then close when the vacuum gauge (B) reaches the green area (C).

Maintenance — Power Train / High Voltage Battery Coolant / Refilling illustration

Note
Make sure that the valves other than the vacuum valve (A) are closed.
4.
Connect the coolant suction hose (A) to SST (0K253 - J2300) coolant filler valve and place the opposite hose in the bucket (B) containing new coolant.

Maintenance — Power Train / High Voltage Battery Coolant / Refilling illustration

5.
Turn the suction valve (A) in the direction of the arrow to fill new coolant, and then close it when the vacuum gauge reaches to '0'.

Maintenance — Power Train / High Voltage Battery Coolant / Refilling illustration

Note
Check that the valve except the suction valve (A) is locked.
6.
Remove the cap adapter (0K253 - J2320).

Maintenance — Power Train / High Voltage Battery Coolant / Refilling illustration

7.
Perform the order below with the KDS.
(Actuation Test → Vehicle Control → Battery EWP Operation Mode for Degassing and Circulation)
Note
Charge the auxiliary 12 V battery during performing "Battery Electric Water Pump Control" to prevent battery drain.
Information
When driving EWP, operate within 10 minutes.
8.
When the battery EWP operates and coolant circulates, refill coolant so that the coolant level is kept between "MAX" and "MIN" level.

Maintenance — Power Train / High Voltage Battery Coolant / Refilling illustration

Note
Friction may damage the bearing if the EWP is operated without coolant.
9.
When the operational sound volume of the EWP becomes small and when no air bubbles can be seen in the reservoir tank, bleeding of the coolant system is completed.
Note
•
After air bleeding is completed make sure that coolant in the reservoir tank flow without air bubble during the EWP actuation.
•
If the coolant flow is not seen or air bubbles are still seen, repeat steps 7 to 8.
10.
After air bleeding is completed, refill the coolant to the MAX level and install the reservoir cap.

Maintenance — Power Train / High Voltage Battery Coolant / Refilling illustration

11.
Check the coolant for leakage.
Note
The cooling system air bleeding and coolant injection are performed perfectly when the coolant is completely cooled. Check the coolant level of the reservoir tank for 2 - 3 days after flushing the coolant.
12.
Install the front under cover.
(Refer to Motor & Reduction Gear System - "Front Under Cover")

Motor Coolant Drain

Special Service Tool
Tool Name / Number
Illustration
Description
Coolant refiller & suction tool
0K253 - J2300

Maintenance — Power Train / Motor Coolant / Drain / Special Service Tool illustration

Used to drain and fill the coolant for EV
Cap adapter
0K253 - J2320

Maintenance — Power Train / Motor Coolant / Drain / Special Service Tool illustration

Used to drain and fill the coolant for EV

SST (0K253 - J2300) Detail Name

Maintenance — Power Train / Motor Coolant / Drain / Special Service Tool illustration

Maintenance — Power Train / Motor Coolant / Drain / Special Service Tool illustration

1. Pressure Valve
2. Suction Valve
3. Vacuum Valve 1
4. Vacuum Valve 2
5. Coolant Injection
6. Vacuum Valve
7. Regulator Pressure Gauge
8. Pressure Gauge
9. Vacuum Gauge
10. Air Pressurization Valve
11. Vacuum Outlet Valve
12. Air Hose Inlet Valve
13. Regulator Adjusting Knob

Drain
Warning
•
When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
•
When working a high voltage system, the technician must be recognized and observe "General Safety Information and Caution". If do not follow, serious accidents like electric shock and short circuit are caused.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Disconnect the battery negative ( - ) terminal and the high voltage service interlock connector.
(Refer to Battery Control System - "Battery (12 V)")
(Refer to Battery Control System - "Battery (12 V)" - 4WD)
2.
Open the reservoir tank cap (A).

Maintenance — Power Train / Motor Coolant / Drain illustration

3.
Install the cap adapter (0K253 - J2320).

Maintenance — Power Train / Motor Coolant / Drain illustration

4.
Install the radiator cap connection hose (A) to the radiator cap adapter (B).

Maintenance — Power Train / Motor Coolant / Drain illustration

5.
Connect the radiator cap connection hose (A) to the air pressurization valve of SST (0K253 - J2300).

Maintenance — Power Train / Motor Coolant / Drain illustration

6.
Install the air hose (A) to the air inlet valve of SST (0K253 - J2300).

Maintenance — Power Train / Motor Coolant / Drain illustration

Note
Make sure all valves are closed.

Maintenance — Power Train / Motor Coolant / Drain illustration

7.
Turn the regulator adjusting knob (A) to set pressure gauge (B) to 0.2 Mpa.

Maintenance — Power Train / Motor Coolant / Drain illustration

Note
After adjusting the pressure, close the regulator adjustment knob.
8.
Remove the rear under cover.
(Refer to Motor and Reduction Gear System - "Rear Under Cover")
9.
Disconnect the cooling hose (A) after releasing the quick connector.

Maintenance — Power Train / Motor Coolant / Drain illustration

10.
Install the coolant drain adapter and hose (A) to the cooling hose.

Maintenance — Power Train / Motor Coolant / Drain illustration

11.
Put the opposite of the coolant drain adapter and hose (A) to a bucket (B).

Maintenance — Power Train / Motor Coolant / Drain illustration

12.
Turn the pressure valve (A) the direction of the arrow to drain coolant.

Maintenance — Power Train / Motor Coolant / Drain illustration

Note
Make sure that the valves other than the pressure valve (A) are closed.
13.
Close the pressure valve after draining coolant, and then install the cooling hose (A).

Maintenance — Power Train / Motor Coolant / Drain illustration

14.
Separate the radiator cap connection hose (A) to the air pressurization valve.

Maintenance — Power Train / Motor Coolant / Drain illustration

Motor Coolant Refilling

Special Service Tool
Tool Name / Number
Illustration
Description
Coolant refiller & suction tool
0K253 - J2300

Maintenance — Power Train / Motor Coolant / Refilling / Special Service Tool illustration

Used to drain and fill the coolant for EV
Cap adapter
0K253 - J2320

Maintenance — Power Train / Motor Coolant / Refilling / Special Service Tool illustration

Used to drain and fill the coolant for EV

SST (0K253 - J2300) Detail Name

Maintenance — Power Train / Motor Coolant / Refilling / Special Service Tool illustration

Maintenance — Power Train / Motor Coolant / Refilling / Special Service Tool illustration

1. Pressure Valve
2. Suction Valve
3. Vacuum Valve 1
4. Vacuum Valve 2
5. Coolant Injection
6. Vacuum Valve
7. Regulator Pressure Gauge
8. Pressure Gauge
9. Vacuum Gauge
10. Air Pressurization Valve
11. Vacuum Outlet Valve
12. Air Hose Inlet Valve
13. Regulator Adjusting Knob

Refilling
Note
•
Be careful not to spill coolant on the electric devices when replacing the coolant.
•
Use genuine antifreeze/coolant.
•
To prevent corrosion, the concentration of coolant should be maintained at a minimum of 45%. If the coolant concentration is less than 45%, there may be a risk of corrosion or freezing.
•
It is not recommended if the concentration of the coolant exceeds 60%, as the cooling effect may be reduced.
•
Do not mix antifreeze/coolant from different brands.
•
Do not add any anti-rust.
1.
Drain the motor coolant.
(Refer to Motor Coolant - "Drain")
2.
Connect the radiator cap connection hose (A) to the vacuum valve of SST (0K253 - J2300).

Maintenance — Power Train / Motor Coolant / Refilling illustration

3.
Open the vacuum valve (A) in the direction of the arrow, and then close when the vacuum gauge (B) reaches the green area (C).

Maintenance — Power Train / Motor Coolant / Refilling illustration

Note
Make sure that the valves other than the vacuum valve (A) are closed.
4.
Connect the coolant suction hose (A) to SST (0K253 - J2300) coolant filler valve and place the opposite hose in the bucket (B) containing new coolant.

Maintenance — Power Train / Motor Coolant / Refilling illustration

5.
Turn the suction valve (A) in the direction of the arrow to fill new coolant, and then close it when the vacuum gauge reaches to '0'.

Maintenance — Power Train / Motor Coolant / Refilling illustration

Note
Check that the valve except the suction valve (A) is locked.
6.
Remove the cap adapter (0K253 - J2320).

Maintenance — Power Train / Motor Coolant / Refilling illustration

7.
Perform the order below with the KDS.
(S/W Management → Vehicle Control → Electric Water Pump Control)
Note
Charge the auxiliary 12 V battery during performing "Electric Water Pump Control" to prevent battery drain.
Information
When driving EWP, operate within 10 minutes.
8.
When the EWP operates and coolant circulates, refill coolant so that the coolant level is kept between "MAX" and "MIN" level.

Maintenance — Power Train / Motor Coolant / Refilling illustration

Note
Friction may damage the bearing if the EWP is operated without coolant.
9.
When the operational sound volume of the EWP becomes small and when no air bubbles can be seen in the reservoir tank, bleeding of the coolant system is completed.
Note
•
After air bleeding is completed make sure that coolant in the reservoir tank flow without air bubble during the EWP actuation.
•
If the coolant flow is not seen or air bubbles are still seen, repeat steps 7 to 8.
10.
Install the rear under cover.
(Refer to Motor and Reduction Gear System - "Rear Under Cover")

Other information:

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Front Subframe Removal and Installation - 2WD

Special Service Tool Tool Name / Number Illustration Description Ball joint puller09568 - 2J100 Used for removal of tie rod end Lower arm ball joint remover0K545 - A9100 Used for removal of front lower arm ball joint Removal • When working on high voltage system, the work should be performed by technicians who have completed the relevant training.

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Front seat adjustment for manual seat: (if equipped)

Forward/backward seat adjustment Seat cushion height adjustment Seatback recline angle adjustment Use the manual adjustment levers located on the outer side of the Kia EV6 seat cushion to adjust the front seat position. Proper seat adjustment improves driving comfort, visibility, and control of the Kia EV6 steering wheel, pedals, and dashboard controls.

Contents

Categories

 
Copyright © 2026 Kia EV6 Manuals ⏱ 0.0131