Kia EV6: Body (Interior / Exterior / Electrical) / Rear Door

Contents:

Components and Components Location

Component and Component Location
Rear Door [Trim]

Body (Interior / Exterior / Electrical) — Rear Door / Components and Components Location / Component and Component Location illustration

1. Rear Door Delta Cover
2. Rear Door Frame Molding
3. Rear Door Belt Outside Weatherstrip
4. Rear Door Front Frame Garnish
5. Rear Door Rear Frame Garnish
6. Rear Door Side Weatherstrip
7. Rear Door Body Side Weatherstrip
8. Rear Door Trim
9. Power Window Switch
10. Rear Door Inside Handle
11. Rear Door Belt Inside Weatherstrip

Rear Door [Mechanism]

Body (Interior / Exterior / Electrical) — Rear Door / Components and Components Location / Component and Component Location illustration

1. Rear Door Module
1-a. 8.8 - 11.8 N·m (0.9 - 1.2 kgf·m, 6.5 - 8.7 lb·ft)
2. Rear Door Window Motor
2-a. 7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)
3. Rear Door Speaker
3-a. 7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)
4. Rear Door Window Glass
4-a. 8.8 - 11.8 N·m (0.9 - 1.2 kgf·m, 6.5 - 8.7 lb·ft)


5. Rear Door Glass Run
6. Rear Door Channel
6-a. 6.9 - 10.8 N·m (0.7 - 1.1 kgf·m, 5.1 - 8 lb·ft)
7. Rear Door Latch
8. Rear Door Outside Handle
8-a. 3.4 - 5.7 N·m (0.35 - 0.58 kgf·m, 2.5 - 4.2 lb·ft)

Adjustment

Adjustment
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Door Adjustment
1.
Check that the gap between the door and the body is even after parking in a flat level.

Body (Interior / Exterior / Electrical) — Rear Door / Adjustment illustration

2.
Loosen the door hinge (A) bolts (B), adjust the door (C) by moving it back and forth, left and right, and then tighten the bolts.

Tightening torque :
21.6 - 26.5 N·m (2.2 - 2.7 kgf·m, 15.9 - 19.5 lb·ft)

Body (Interior / Exterior / Electrical) — Rear Door / Adjustment illustration

Body (Interior / Exterior / Electrical) — Rear Door / Adjustment illustration

3.
Check that the gap between the door and the body is even.
Striker Adjustment
1.
Loosen the screws (B) and adjust the striker (A) by moving it back and forth, left and right, and then tighten the screws.

Tightening torque :
18.6 - 33.3 N·m (1.9 - 3.4 kgf·m, 13.7 - 24.6 lb·ft)

Body (Interior / Exterior / Electrical) — Rear Door / Adjustment illustration

2.
Check that the door opens and closes properly.
Glass Adjustment
Note
Check the damage of the glass run and channel and replace them if necessary.
1.
Remove the rear door trim.
(Refer Rear Door - "Rear Door Trim")
2.
Adjust the gap by moving the window glass (A) up, down, left and right, and then tighten the bolt.

Tightening torque :
8.8 - 11.8 N·m (0.9 - 1.2 kgf·m, 6.5 - 8.7 lb·ft)

Body (Interior / Exterior / Electrical) — Rear Door / Adjustment illustration

3.
Check the window glass for normal operation.
Window Motor Reset
1.
With the window open, use the auto/manual up switch to completely close the window and keep it closed for more than 0.2 seconds.
(If you operate the up switch while the window is completely closed, it will not be initialized)

On Vehicle Inspection

On Vehicle Inspection
Diagnostic with KDS
1.
The rear door can be quickly diagnosed for problems with the KDS. (Refer to "DTC guide")
(1)
Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS.
(Refer to DTC guide when fault code is found.)
Information
Refer to the KDS screen for operating conditions and details
Protection of Window Motor Overheating
1.
The motor can continuously operate at least 15 strokes, and it can be operated again 30 to 40 seconds after the motor stops due to the overheat protection function.

Rear Door Garnish and Molding Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Door Frame Molding
1.
Remove the molding (A).

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Garnish and Molding / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Garnish and Molding / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Garnish and Molding / Removal and Installation / Removal illustration

Door Frame Garnish [Front Side]
1.
Remove the rear door belt outside weatherstrip.
(Refer to Rear Door - "Rear Door Weatherstrip")
2.
Remove the garnish (A).

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Garnish and Molding / Removal and Installation / Removal illustration

Door Frame Garnish [Rear Side]
1.
Remove the rear door delta cover.
(Refer Rear Door - "Rear Door Trim")
2.
Remove the rear door belt outside weatherstrip.
(Refer to Rear Door - "Rear Door Weatherstrip")
3.
Remove the screw (A).

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Garnish and Molding / Removal and Installation / Removal illustration

4.
Remove the garnish (A).

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Garnish and Molding / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Garnish and Molding / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Garnish and Molding / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Rear Door Handle Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Door Inside Handle
1.
Remove the rear door trim.
(Refer to Rear Door - "Rear Door Trim")
2.
Remove the handle (A) after removing the screws.

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Handle / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Handle / Removal and Installation / Removal illustration

Door Outside Handle
1.
Remove the rear door module.
(Refer to Rear Door - "Rear Door Module")
2.
Disconnect the handle connector (A).

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Handle / Removal and Installation / Removal illustration

3.
Separate the connector wiring (A).

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Handle / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Handle / Removal and Installation / Removal illustration

4.
Separate the door latch rod (A).

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Handle / Removal and Installation / Removal illustration

5.
Remove the handle (A) after removing the nuts.

Tightening torque :
3.4 - 5.7 N·m (0.35 - 0.58 kgf·m, 2.5 - 4.2 lb·ft)

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Handle / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Handle / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Rear Door Latch Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Remove the rear door module.
(Refer to Rear Door - "Rear Door Module")
2.
Remove the door channel (A) after removing the nuts.

Tightening torque :
6.9 - 10.8 N·m (0.7 - 1.1 kgf·m, 5.1 - 8.0 lb·ft)

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Latch / Removal and Installation / Removal illustration

3.
Disconnect the door outside handle connector (A).

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Latch / Removal and Installation / Removal illustration

4.
Separate the connector wiring (A).

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Latch / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Latch / Removal and Installation / Removal illustration

5.
Separate the door latch rod (A).

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Latch / Removal and Installation / Removal illustration

6.
Remove the screws (A).

Tightening torque :
6.9 - 10.8 N·m (0.7 - 1.1 kgf·m, 5.1 - 8.0 lb·ft)

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Latch / Removal and Installation / Removal illustration

7.
Remove the door latch (A).

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Latch / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Rear Door Latch Inspection

Inspection
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Remove the rear door latch.
(Refer to Rear Door - "Rear Door Latch")
2.
Apply voltage to connector terminal and check that the door latch operates properly.

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Latch / Inspection illustration

Location
Terminal
Driver
7, 8
Passenger
1, 2

Rear Door Module Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Remove the rear door window glass.
(Refer to Rear Door - "Rear Door Window Glass")
2.
Disconnect the door main wiring connector (A).

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Module / Removal and Installation / Removal illustration

3.
Separate the door module (A) after removing the bolts.

Tightening torque :
8.8 - 11.8 N·m (0.9 - 1.2 kgf·m, 6.5 - 8.7 lb·ft)

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Module / Removal and Installation / Removal illustration

4.
Remove the door module after disconnecting the wiring connectors (A).

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Module / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Module / Removal and Installation / Removal illustration

5.
Separate the wiring harness (A).

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Module / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Module / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Rear Door Speaker Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Door Speaker
1.
Remove the rear door trim.
(Refer to Rear Door - "Rear Door Trim")
2.
Separate the speaker connector (A).

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Speaker / Removal and Installation / Removal illustration

3.
Remove the speaker (A) after removing the bolts.

Tightening torque :
7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Speaker / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Rear Door Switch Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Door Switch
1.
Remove the rear door trim.
(Refer to Rear Door - "Rear Door Trim")
2.
Remove the switch (A) by pulling the hook in the direction of the arrow.

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Switch / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Switch / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Rear Door Trim Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Door Delta Cover
1.
Remove the cover (A).

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Trim / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Trim / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Trim / Removal and Installation / Removal illustration

Door Trim
1.
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
(1)
Open the front trunk (A).

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Trim / Removal and Installation / Removal illustration

(2)
Open the auxiliary 12 V battery service cover (A).

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Trim / Removal and Installation / Removal illustration

(3)
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).

Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Trim / Removal and Installation / Removal illustration

(4)
Disconnect the service interlock connector (A).

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Trim / Removal and Installation / Removal illustration

Warning
•
Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
•
When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
Note
The service interlock connector cannot be completely removed.

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Trim / Removal and Installation / Removal illustration

2.
Remove the delta cover.
3.
Separate the trim (A) after removing the screw.

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Trim / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Trim / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Trim / Removal and Installation / Removal illustration

4.
Press the hook (B) and separate the rear door inside handle cage (A).

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Trim / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Trim / Removal and Installation / Removal illustration

5.
Remove the door trim after disconnecting the connectors (A).
(1)
Disconnect the tweeter speaker connector (A).

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Trim / Removal and Installation / Removal illustration

(2)
Disocnnect the rear mood lamp connector (A).

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Trim / Removal and Installation / Removal illustration

(3)
Disconnect the power window switch connector (A).

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Trim / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Rear Door Weatherstrip Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Door Side Weatherstrip
1.
Separate the door checker (A) after removing the bolt.

Tightening torque :
21.6 - 32.4 N·m (2.2 - 3.3 kgf·m, 15.9 - 23.9 lb·ft)

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Weatherstrip / Removal and Installation / Removal illustration

2.
Remove the weatherstrip (A).

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Weatherstrip / Removal and Installation / Removal illustration

Door Body Side Weatherstrip
1.
Remove the weatherstrip (A).

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Weatherstrip / Removal and Installation / Removal illustration

Door Belt Outside Weatherstrip
1.
Remove the weatherstrip (A).

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Weatherstrip / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Weatherstrip / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Weatherstrip / Removal and Installation / Removal illustration

Door Belt Inside Weatherstrip
1.
Remove the rear door trim.
(Refer to Rear Door - "Rear Door Trim")
2.
Remove the weatherstrip (A).

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Weatherstrip / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Rear Door Window Glass Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Door Window Glass
1.
Remove the rear door belt inside and outside weatherstrips.
(Refer to Rear Door - "Rear Door Weatherstrip")
2.
Remove the rear door frame garnish. [Rear side]
(Refer to Rear Door - "Rear Door Garnish and Molding")
3.
Separate the door channel (A) in the direction of the arrow after removing the nuts.

Tightening torque :
6.9 - 10.8 N·m (0.7 - 1.1 kgf·m, 5.1 - 8.0 lb·ft)

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Window Glass / Removal and Installation / Removal illustration

4.
Operate the power window switch to lower the window glass until the window glass bolts is visible in the service hole.
5.
remove the window glass (A) after removing the bolt.

Tightening torque :
8.8 - 11.8 N·m (0.9 - 1.2 kgf·m, 6.5 - 8.7 lb·ft)

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Window Glass / Removal and Installation / Removal illustration

Door Window Glass Run
1.
Remove the door window glass.
2.
Remove the rear door frame garnish. [Front side]
(Refer to Rear Door - "Rear Door Garnish and Molding")
3.
Remove the glass run (A).

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Window Glass / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Rear Door Window Motor Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Door Window Motor
1.
Remove the rear door trim.
(Refer Rear Door - "Rear Door Trim")
2.
Remove the motor connector (A).

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Window Motor / Removal and Installation / Removal illustration

3.
Remove the motor (A) after removing the bolts.

Tightening torque :
7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)

Body (Interior / Exterior / Electrical) — Rear Door / Rear Door Window Motor / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.
2.
Perform the window motor reset procedure.
(Refer to Rear Door - "Adjustment")

Other information:

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Noise and smoke

When the airbags in the Kia EV6 deploy, a loud noise will be heard and smoke or powder may appear inside the cabin. This is a normal result of the airbag inflator operation and does not indicate a fire. Following deployment, occupants may experience temporary breathing discomfort caused by the force of the seat belt, airbag deployment, and exposure to the harmless smoke and powder released during inflation.

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Gear position

The Kia EV6 instrument cluster displays the currently selected gear position whenever the EV button is in the DRIVE READY or POWER ON mode. P (Park) Always bring the Kia EV6 to a complete stop before shifting into P (Park). To shift from R (Reverse), N (Neutral), or D (Drive) into P (Park), press the [P] button. If the Kia EV6 is switched OFF while stationary, the transmission system automatically shifts into P (Park).

 
Copyright © 2026 Kia EV6 Manuals ⏱ 0.0221