Kia EV6: Restraint

Contents:

Single-Use Parts

Single-Use Parts
Non-reusable parts (Single-Use Parts)
Workshop manual provides “Components and Components Location” which can be used to identify “Non-reusable parts”. When repairing a vehicle, Non-reusable parts such as fasteners, gaskets, washers, clips and garnishes must be replaced. Kia Non-reusable parts are designed to be installed only once.
Before working on a vehicle, check “Components and Components Location” to find the non-reusable parts in a system.
※ Symbol of Non-reusable parts
Symbol
Meaning

Restraint — Single-Use Parts illustration

Do not reuse the part. Replace with a new one.

※ Example of “Components and Components Location”

Restraint — Single-Use Parts illustration

High Voltage System General Safety Information and Caution ➤

High Voltage Shut-off Procedures

High Voltage Shut-off Procedures

High Voltage Shut-off Procedures
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Information
High Voltage Component : Battery System Assembly (BSA), motor assembly, inverter assembly, high voltage junction box, power cable, etc.
1.
Check the Battery Management Unit (BMU) weld flag with the KDS.
(Data Analysis → Battery Management System (BMS) → BMU Weld Flag)

Specified value : NO

Information
Refer to the KDS screen for operating conditions and details.
2.
Open the front trunk (A).

Restraint — High Voltage Shut-off Procedures illustration

3.
Open the low voltage (12 V) battery service cover (A).

Restraint — High Voltage Shut-off Procedures illustration

4.
Turn the POWER OFF, separate the low voltage (12 V) battery ( - ) terminal (A).

Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)

Restraint — High Voltage Shut-off Procedures illustration

5.
Disconnect the service interlock connector (A).

Restraint — High Voltage Shut-off Procedures illustration

Warning
•
Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
•
When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
Note
The service interlock connector cannot be completely removed.

Restraint — High Voltage Shut-off Procedures illustration

6.
Remove the front under cover.
(Refer to Motor and Reduction Gear System - "Front Under Cover")
7.
Remove the high voltage battery cover (A).

Tightening torque :
7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)

Restraint — High Voltage Shut-off Procedures illustration

8.
Disconnect the front high voltage junction box power cable (A).

Restraint — High Voltage Shut-off Procedures illustration

Note
How to disconnect the connector
1)
Release the locking clip (A) by pulling it.
2)
Disconnect the connector by pushing the lever (A) in the direction of the arrow while pressing the locking clip (B).

Restraint — High Voltage Shut-off Procedures illustration

9.
Remove the center floor rear under cover.
(Refer to Motor and Reduction Gear System - "Rear Under Cover")
10.
Disconnect the Integrated Charge Control Unit (ICCU) connector (A).

Restraint — High Voltage Shut-off Procedures illustration

Note
How to disconnect the connector
1)
Release the locking clip (A) by pulling it.
2)
Disconnect the connector while pressing the locking clip (B).

Restraint — High Voltage Shut-off Procedures illustration

11.
Disconnect the rear high voltage junction box power cable (A).

Restraint — High Voltage Shut-off Procedures illustration

Note
How to disconnect the connector
1)
Release the locking clip (A) by pulling it.
2)
Disconnect the connector by pushing the lever (A) in the direction of the arrow while pressing the locking clip (B).

Restraint — High Voltage Shut-off Procedures illustration

12.
Measure the voltage between the high voltage power connector and high voltage battery terminal to check whether the high voltage is shut-off.

30 V or less : Normal cut off high voltage circuit
Above 30 V : Fault on high voltage circuit

(1)
Measure the voltage between the high voltage power connector positive ( + ) terminal and negative ( - ) terminal.

Restraint — High Voltage Shut-off Procedures illustration

(2)
Measure the voltage between the high voltage battery positive ( + ) and negative ( - ) terminal.

Restraint — High Voltage Shut-off Procedures illustration

(3)
Measure the voltage between the high voltage battery positive ( + ) terminal and ground.

Restraint — High Voltage Shut-off Procedures illustration

(4)
Measure the voltage between the high voltage battery negative ( - ) terminal and ground.

Restraint — High Voltage Shut-off Procedures illustration

(5)
Measure the voltage between the rear high voltage battery positive ( + ) and negative ( - ) terminal.

Restraint — High Voltage Shut-off Procedures illustration

(6)
Measure the voltage between the rear high voltage battery positive ( + ) terminal and ground.

Restraint — High Voltage Shut-off Procedures illustration

(7)
Measure the voltage between the rear high voltage battery negative ( - ) terminal and ground.

Restraint — High Voltage Shut-off Procedures illustration

Warning
1)
Check for insulation breakdown via KDS and physical leakage current before working on EV.
2)
Remove the main fuse if insulation breakdown or leakage current is suspected. (Remove the main fuse even when DTC CODE ON such as PRA malfunction)
(Refer to High Voltage Battery Control System - "Main Fuse")
※ If there is no insulation breakdown or leakage current and it is normal, work without removing the main fuse.

Specification

Tightening Torque

Tightening Torque
Airbag Module
Curtain Airbag (CAB)
Item
N·m
kgf·m
lb·ft
lb·in
Curtain Airbag (CAB) bolt
7.8 - 11.8
0.8 - 1.2
5.8 - 8.7
-
Curtain Airbag (CAB) nut
3.9 - 5.9
0.4 - 0.6
2.9 - 4.3
34.7 - 52.1

Passenger Airbag (PAB)
Item
N·m
kgf·m
lb·ft
lb·in
Passenger Airbag (PAB) bolt
3.9 - 5.9
0.4 - 0.6
2.9 - 4.3
34.7 - 52.1

Side Airbag (SAB)
Item
N·m
kgf·m
lb·ft
lb·in
Side Airbag (SAB) nut
5.9 - 7.8
0.6 - 0.8
4.3 - 5.8
52.1 - 69.4

Seat Belt System
Height Adjust
Item
N·m
kgf·m
lb·ft
lb·in
Front seat belt upper anchor bolt
39.2 - 53.9
4.0 - 5.5
28.9 - 39.8
-
Height adjuster bolt
39.2 - 53.9
4.0 - 5.5
28.9 - 39.8
-

Seat Belt Pretensioner (BPT)
Item
N·m
kgf·m
lb·ft
lb·in
Seat Belt Pretensioner (BPT) bolt
44.1 - 54.9
4.5 - 5.6
32.5 - 40.5
-

Seat Belt Reminder
Item
N·m
kgf·m
lb·ft
lb·in
Seat belt buckle bolt and nut
44.1 - 53.9
4.5 - 5.5
32.5 - 39.8
-

SRSCM
Acceleration type Side Impact Sensor (A-SIS)
Item
N·m
kgf·m
lb·ft
lb·in
Acceleration type Side Impact Sensor (A-SIS) bolt
7.5 - 9.1
0.76 - 0.93
5.5 - 6.7
-

Airbag Control Unit (ACU)
Item
N·m
kgf·m
lb·ft
lb·in
Airbag Control Unit (ACU) nut
7.7 - 9.5
0.79 - 0.97
5.7 - 7.0
-

Front Impact Sensor (FIS)
Item
N·m
kgf·m
lb·ft
lb·in
Front Impact Sensor (FIS) nut
7.5 - 9.1
0.76 - 0.93
5.5 - 6.7
-

Pressure type Side Impact Sensor (P-SIS)
Item
N·m
kgf·m
lb·ft
lb·in
Pressure type Side Impact Sensor (P-SIS) screw
2.0 - 3.0
0.20 - 0.31
1.4 - 2.2
17.4 - 26.9

Special Service Tools

Special Service Tool
Tool Name / Number
Illustration
Description
Deployment tool
0957A - 34100A

Restraint — Special Service Tools / Special Service Tool illustration

Use when deploying airbag module
Deployment adapter
0K57A - 3U100A

Restraint — Special Service Tools / Special Service Tool illustration

Use when deploying DAB, PAB, CAB modules and BPT
Used with the airbag deployment tool (9057A - 34100A)
Deployment adapter
0957A - 2W100

Restraint — Special Service Tools / Special Service Tool illustration

Used when deploying the SAB module
Used with the airbag deployment tool (9057A - 34100A)
Dummy
0957A - 38200

Restraint — Special Service Tools / Special Service Tool illustration

Use to check the resistance of the airbag module
Dummy adapter
0957A - 2W200

Restraint — Special Service Tools / Special Service Tool illustration

Use to check the resistance of SAB and KAB modules
Used with 0957A - 38200
Dummy adapter
0957A - 2G000

Restraint — Special Service Tools / Special Service Tool illustration

Use to check resistance of DAB, PAB, CAB modules and BPT
Used with 0957A - 38200
Deployment adapter
0957A - 3F100

Restraint — Special Service Tools / Special Service Tool illustration

Use when deploying KAB modules
Use with 0957A - 34100A
Dummy adapter
0957A - 3F000

Restraint — Special Service Tools / Special Service Tool illustration

Use to check KAB module resistance
Use with 0957A - 38200

Information
Name
Abbreviation
Curtain Airbag
CAB
Driver Airbag
DAB
Knee Airbag
KAB
Passenger Airbag
PAB
Side Airbag
SAB

General Safety Information and Caution

Precautions when repairing the airbag system
When repairing the SRS, pay attention to the following items.
Warning
If the items below are not observed, there is a possibility of serious injury due to unexpected airbag deployment, and the airbag may not operate.
1.
After disconnecting the ( - ) terminal of the auxiliary 12 V battery in the POWER OFF state, wait at least 3 minutes and 30 seconds before starting related work. (Backup power is valid for about 150ms)
2.
Failure symptoms of the airbag system are difficult to identify. When troubleshooting, the DTC provides the most important information.
3.
When repairing an airbag system fault, always inspect the DTC before removing the battery.
4.
Do not measure the resistance of the airbag squib connector. (It is very dangerous because the airbag can be activated.)
Information
Squib : It is an ignition device installed in the inflator of the electric airbag module.
5.
Be careful not to damage the airbag module by oil, grease, cleaner and water.
6.
Do not use airbag components from other vehicles.
7.
When replacing components, replace them with new ones.
8.
Do not disassemble or repair to reuse for all airbag system components.
9.
When installing the airbag system, be careful not to impact around the airbag control unit and impact sensor. The airbag may be suddenly deployed, which may cause damage and injury.
10.
If the airbag module is dropped or other defects such as cracks, dents on the case, the bracket and the connector are occurred, replace them with new ones.

Restraint — General Safety Information and Caution / Precautions when repairing the airbag system illustration

11.
After completing the SRS repair, check the warning lamp and delete the DTC.
Note
The operation of the airbag warning light may be blocked by other circuit faults. Therefore, when the airbag warning light turns on, the DTC is deleted by using the KDS.
12.
After completing the repair and inspection of the SRS, be sure to initialize the system. (Keep POWER ON for more than 7 seconds → Keep POWER OFF for more than 3 minutes and 30 seconds → Keep POWER ON for more than 7 seconds)
Airbag Handling and Storage
1.
Do not disassemble the airbag.
2.
The deployed airbags cannot be reused.
3.
Be sure to observe the following precautions when storing the airbag module.
•
Store the airbag module with the top side of the cover facing upward.
•
The double locking connector lever must be locked, and positioned so that the connector is not damaged.
•
Be careful not to damage the airbag module by oil, grease, cleaner and water.

Restraint — General Safety Information and Caution / Precautions when repairing the airbag system illustration

•
Store in a place where the ambient temperature is below 60°C (140°F), humidity is not high, and there is no electrical noise.
•
Follow the disposal procedure for the damaged airbag modules.
(Refer to Airbag Module - "The Airbag Module Disposal Procedure")
Wiring Precautions
Observe the precautions described below.
•
Never reconnect or repair the damaged airbag wiring. If the airbag wiring is damaged, replace the harness.

Restraint — General Safety Information and Caution / Precautions when repairing the airbag system illustration

•
Make sure the wiring is not interfered with other components.

Restraint — General Safety Information and Caution / Precautions when repairing the airbag system illustration

•
Make sure that there are no foreign substances on the connector surface of the airbag module . Poor grounding can cause problems which are difficult to diagnose.
Precautions for Inspections
•
When using the tester, insert the tester probe into the connector wire side. Do not insert the tester probe into the terminal side of the connector.
•
Use a U-shaped probe and do not forcefully insert the probe.

Restraint — General Safety Information and Caution / Precautions when repairing the airbag system illustration

Airbag Module Connector Precautions
•
To disconnect the connector, remove the connector by holding the connector and pulling the spring loaded sleeve (A) and slider (B) from the opposite side. Be careful to pull the sleeve, not the connector.

Restraint — General Safety Information and Caution / Precautions when repairing the airbag system illustration

•
Hold both connectors and push firmly until the protrusion (C) of the connector on the sleeve side clicks into place.

Restraint — General Safety Information and Caution / Precautions when repairing the airbag system illustration

Description and Operation

Description
•
The airbag system is a supplemental restraint system to protect the driver and passengers from injuries by operating the airbags and seat belt pretensioner installed on the driver's and front passenger's seats in the event of a vehicle collision.
•
The airbag system is configured as follows.
Name
Abbreviation
Airbag and seat belt warning light
-
Airbag Control Unit
ACU
Clock spring
-
Curtain Airbag
CAB
Driver Airbag
DAB
Front Impact Sensor
FIS
Knee Airbag
KAB
Passenger Airbag
PAB
Seat Belt Pretensioner
BPT
Side Airbag
SAB
Side Impact Sensor
Acceleration type Front
A-FSIS
Acceleration type Rear
A-RSIS
Pressure type
P-SIS

Airbag Warning Light
The airbag control unit turns on the airbag warning light by detecting whether there is an abnormality in the airbag system when the power is applied.
1.
When the airbag system is normal, the airbag warning light turns on for 3 to 6 seconds and turns off.

Restraint — Description and Operation / Airbag Warning Light illustration

2.
If there is a problem with the airbag system, the warning lamp will be on for 3 to 6 seconds, then go off for 1 second, then come back on and stay on.

Restraint — Description and Operation / Airbag Warning Light illustration

3.
When in the variant coding mode.
•
When POWER ON, the airbag warning light turns on for 3 seconds.
•
The airbag warning lamp blinks at 1 second intervals until the variant coding is normally completed.
•
When variant coding is normally completed, the airbag warning lamp turns on for 6 seconds and then turns off.

Restraint — Description and Operation / Airbag Warning Light illustration

•
When variant coding is not normally completed, the airbag warning lamp continues to blink at 1 second intervals.

Restraint — Description and Operation / Airbag Warning Light illustration

Note
•
If there is a failure of the airbag system or an internal failure of the airbag system control module, variant coding should be re-performed after confirming the cause of failure and completing the action using the KDS.
•
In the following cases, the airbag warning light continues to illuminate.
–
If there is a failure of the airbag system or an internal failure of the airbag control unit.
–
If there is a Diagnostic Trouble Code (DTC).
•
If a failure occurs in which the airbag control module cannot operate, the operation of the airbag warning lamp cannot be controlled normally.

Repair Procedures

Replacement of components after deploying the airbag system
Note
Before the work related to the airbag, Check the Diagnosis Trouble Code (DTC) with the KDS.
1.
When the airbags deployed after a collision, replace the following items.
(1)
Airbag Control Unit (ACU)
(2)
Replace the clock spring if there is any problem after checking the clock spring for damage when the driver airbag is deployed.
(3)
Damaged impact sensor
(4)
Airbag wiring harness
2.
Check that the airbag system operates normally after repairing the vehicle.
Note
When POWER ON the airbag warning light should turn off after turning on for 3 - 6 seconds.

Airbag Module ➤

Seat Belt System ➤

SRSCM ➤

Other information:

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Tires and Wheels

Proper tire maintenance is essential for the safety, efficiency, comfort, and overall performance of the Kia EV6. To achieve the best driving experience, always maintain the recommended tire inflation pressures and stay within the specified load limits and weight-distribution guidelines provided for your vehicle. Recommended Cold Tire Inflation Pressures All tire pressure measurements should be performed when the tires are cold.

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Highway Lane Change Assist: (if equipped)

Display and control You can check the operating status of the Highway Lane Change Assist function in the Driving Assist view on the Kia EV6 instrument cluster. For more information about the related graphics and indicators, refer to the LCD display section. The Highway Lane Change Assist status is displayed on the Kia EV6 cluster as follows: Figure 1.

Contents

Categories

 
Copyright © 2026 Kia EV6 Manuals ⏱ 0.0115