Kia EV6: Restraint / Airbag Module
Contents:
Components and Components Location. Description and Operation
Components and Components Location

1. Driver Airbag (DAB) 2. Clock Spring 3.
Passenger Airbag (PAB) 4. Side Airbag (SAB) [Driver's Side]
|
5. Side Airbag (SAB) [Passenger's Side] 6. Curtain Airbag (CAB)
|
Description and Operation
|
•
|
The airbag plays a role in protecting the driver by deploying in the event of a severe collision or
rollover accident.
|
|
•
|
The airbag consists of driver, knee, and passenger airbags deployed in frontal collisions and side and
curtain airbags deployed in side collisions or rollover accidents.
|
On Vehicle Inspection
Diagnosis with KDS
| 1. |
The airbag module can be more quickly diagnosed for problems with the KDS (Refer to "DTC guide").
| (1)
|
Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS.
(Refer to DTC guide when fault code is found)
|
|
Airbag Module Disposal Procedure
| Airbag Module Disposal Procedure |
When scrapping a vehicle equipped with an airbag system such as an airbag or seat Belt Pretensioner (BPT), the
airbag must be deployed first. When deploying the airbag, it must be deployed by a skilled technician, and the used
airbag cannot be reused, so it must not be installed in another vehicle.
|
•
|
If an undeployed airbag is accidentally deployed, it may cause serious injury, so it must be
disposed after deployment.
|
|
•
|
Deployment of the airbag must be performed on a level ground with no risk elements.
|
|
•
|
An explosion sound occurs when the airbag is deployed, perform it in a place where there is no
damage to the surroundings.
|
|
•
|
Smoke may occur when the airbag is deployed, perform the deployment of the airbag in area with good
ventilation and no smoke detector nearby.
|
|
•
|
The airbag is very hot after deploying, so wait at least 30 minutes and let it cool before touching
it.
|
|
•
|
Keep the deployed airbag away from water.
|
|
|
•
|
When scrapping a vehicle, the airbag should, in principle, be deployed while installed in the
vehicle. Do not remove the airbag except unavoidable circumstances.
|
|
•
|
If the airbag is removed from the vehicle due to airbag replacement (accident repair, warranty
repair, etc.), refer to the relevant manual and deploy it outside the vehicle. (Deploying the airbag
inside the vehicle may cause damage to the vehicle.)
|
|
•
|
Do not disassemble the airbag.
|
|
•
|
Be careful not to damage the airbag.
|
|
•
|
Be careful not to drop the airbag.
|
|
•
|
When deploying the airbag, deploy it at least 7 m (22.97 ft.) away from the airbag.
|
|
•
|
When deploying the airbag, always use the special tool and perform it in a place without electrical
noise.
|
|
|
•
|
Wash hands thoroughly with soap after deploying, repacking, and disposal of the airbag.
|
|
•
|
Always wear protective gloves, goggles and earplugs when deploying the airbag.
|
|
Tools and Equipment Required for Disposal of Airbag Modules
Illustration
|
Name
|
Possible Cause
|
|

|
Gloves
|
|
|

|
Goggles
|
|
|

|
Earplugs
|
|
|

|
2 tires with wheels
|
(Top / Bottom)
|
|

|
3 tires without the wheels
|
(Middle)
|
|

|
Rope Strap / Ratchet Strap
|
(Use for connecting the airbag equipment and tires according to the deployment instructions)
|
|

|
12 V battery
|
|
Deployed Inside the Vehicle
| 1. |
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage
service interlock connector.
| (1)
|
Open the front trunk (A).

|
| (2)
|
Open the auxiliary 12 V battery service cover (A).

|
| (3)
|
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).
Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)
|

|
| (4)
|
Disconnect the service interlock connector (A).

|
•
|
Wait more than 5 minutes for capacitor of the high voltage battery system to be
discharged completely.
|
|
•
|
When working on a vehicle during discharging the capacitor, it can cause an
electrical shock or injury, so follow the manual.
|
|
|
The service interlock connector cannot be completely removed.

|
|
|
| 2. |
Make sure the airbag is securely installed.
|
| 3. |
Prepare to deploy the airbag module as follows.
| (1)
|
Disconnect the airbag or seat belt pretensioner connector to be deployed.
|
| (2)
|
Connect the deployment adapter to the airbag or seat belt pretensioner.
|
•
|
For the Driver Airbag (DAB), disconnect the connector, connect the deployment
adapter, and then reinstall it on the steering wheel.
|
|
•
|
When using the deployment adapter, use it appropriately according to the deployment
airbag.
|
|
–
|
DAB, PAB, CAB, BPT (0K57A - 3U100A)
|
|
–
|
For the Driver Airbag (DAB), disconnect the 2-pin connector, connect the deployment
adapter, and then reinstall it on the steering wheel.
|
|
|
|
| 4. |
Workers should be at least 7 meters away from the vehicle.
|
| 5. |
Connect the Special Service Tool (0957A - 34100A) to the deployment adapter and then connect it to the
external battery.
| (2)
|
The Special Service Tool for deployment (0957A - 34100A)
|
| (3)
|
Deployment adapter

|
|
| 6. |
Activate the switch of the airbag deployment tool to deploy the airbag.
| (1)
|
When connecting to an external battery normally , POWER ON (1) is turned on.
|
| (2)
|
If READY (2) button illuminates while pressing READY (2) button, press DEPLOY (3) button to deploy
the airbag.

|
When the airbag is deployed, loud noise is generated, visually confirmed, and after rapid
inflation, it contracts slowly.
|
|
|
| 7. |
Place the deployed airbag in a sturdy plastic bag and sealed securely, then dispose it.

|
Deployment outside of the vehicle
| 1. |
After spreading the rope (A) on the floor in a cross shape, put the tire (B) equipped with the wheel on the
floor.

|
| 2. |
Connect the deployment adapter (A) to the airbag or pretensioner.

|
•
|
For the Driver Airbag (DAB), disconnect the connector, connect the deployment adapter, and
then reinstall it on the steering wheel.
|
|
•
|
When using the deployment adapter, use it appropriately according to the deployment airbag.
|
|
–
|
DAB, PAB, CAB, BPT (0K57A - 3U100A)
|
|
|
| 3. |
Fix the airbag or pretensioner (A) to the wheel.
Airbag

|
If the airbag deployment surface faces downward instead of upward, the airbag may spring up and
cause serious injury to the worker.
|
Pretensioner

|
Install the end of the piston tube of the anchor pretensioner, facing the floor.
|
|
| 4. |
After putting the three waste tires (A), put the tire (B) with the wheel on it.
|
| 5. |
Fix the tire by using the ratchet strap (C).

|
| 6. |
After connecting the battery, connect the airbag deployment tool (0957A - 34100A) to the deployment
adapter.

|
| 7. |
Activate the switch of the airbag deployment tool to deploy the airbag.
| (1)
|
When connecting to an external battery normally, POWER ON (1) is turned on.
|
| (2)
|
If the READY (2) button illuminates while pressing the READY (2) button, press DEPLOY (3) button to
deploy the airbag.
|

|
When the airbag is deployed, loud noise is generated, visually confirmed, and after rapid
inflation, it contracts slowly.
|
|
| 8. |
Place the deployed airbag in a sturdy plastic bag and sealed securely, then dispose it.

|
Clock Spring Description and Operation. Clock Spring Troubleshooting
Clock Spring Description and Operation
The clock spring is a device that transmits the operation signal generated from the sensors installed on the front
and side of the vehicle to the inflator (gas generator) of the airbag via the internal cable. It also transmits the
steering wheel remote control switch and horn operation signals to the system via the internal cable.
|
If the airbag is deployed due to an accident, the clock spring cannot be repaired or reused because there
is a possibility of damage to the clock spring due to heat and impact caused by the explosion of the airbag
inflator (gas generating device). Be sure to replace with a new one.
|
Clock Spring Troubleshooting
Airbag Warning Light On

Noise

Clock Spring Replacement. Curtain Airbag (CAB) Troubleshooting
Clock Spring Replacement
|
The clock spring cannot be replaced individually due to included in the multifunction switch. If necessary,
replace the multifunction switch.
|
| 1. |
Replace the multifunction switch.
(Refer to Body - "Multifunction Switch")
|
Curtain Airbag (CAB) Troubleshooting
|
Direct measuring the resistance of the airbag is very dangerous as it can cause the airbag deployment.
|

Curtain Airbag (CAB) Removal and Installation
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
|
The procedure for removing the Curtain Airbag (CAB) below is for driver's side. Opposite airbag are
performed in the same procedures.
|
| 1. |
Remove the roof trim.
(Refer to Body - "Roof Trim Assembly")
|
| 2. |
Disconnect the CAB connector (A).
|
| 3. |
Remove the CAB (A) after removing the bolts and nuts.
Tightening torque
Bolt : 7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)
Nut : 3.9 - 5.9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7
- 52.1 lb·in)
|
|
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
| 1. |
Install in the reverse order of removal.
|
•
|
Be sure to keep the torque specifications presented in shop manuals. Otherwise, it could
lead to the malfunction of airbag system.
|
|
•
|
Use the color of sentence and line on a airbag to identify curtain airbag module.
Driver's side : Yellow label (attached to
plastic cover)
Passenger's side : Orange label (attached to
plastic cover)
|
|
•
|
Be careful not to twist when the curtain airbag module installing. The curtain airbag
module may not deploy normally if twisted.
|
|
|
| 2. |
Check that the airbag system operates normally.
|
When POWER ON, the airbag warning light should turns off after turning on for 3 - 6 seconds.
|
|
Driver Airbag (DAB) Troubleshooting
|
Direct measuring the resistance of the airbag is very dangerous as it can cause the airbag deployment.
|

Driver Airbag (DAB) Removal and Installation
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedure.
|
|
| 1. |
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage
service interlock connector.
| (1)
|
Open the front trunk (A).
|
| (2)
|
Open the auxiliary 12 V battery service cover (A).
|
| (3)
|
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).
Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)
|
|
| (4)
|
Disconnect the service interlock connector (A).
|
•
|
Wait more than 5 minutes for capacitor of the high voltage battery system to be
discharged completely.
|
|
•
|
When working on a vehicle during discharging the capacitor, it can cause an
electrical shock or injury, so follow the manual.
|
|
|
The service interlock connector cannot be completely removed.
|
|
|
| 2. |
Remove the Driver Airbag (DAB) by pressing the lock levers (B) using the service hole (A).



How to Release the Lock Levers When Removing the DAB Module and How to Install It (Play ▶)
Notes When Refering Video
This video helps clearly identify areas that are hard to distinguish in manual images, such as component
locations or assembly structures.
It also allows visual confirmation of areas that are difficult to see directly due to restricted visibility
caused by surrounding components, from a technician’s perspective.
|
•
|
This video is created using common specifications and may differ from the actual vehicle.
|
|
•
|
The location and repair procedures of the parts may vary depending on vehicle model, model year,
region, and specifications.
|
|
•
|
Check the KDS Guide for detailed information on how to use the KDS.
|
|
•
|
Check the manual for detailed maintenance procedures.
|
|
•
|
Unauthorized reproduction, distribution, or sharing of this video is prohibited.
|
|
| 3. |
Remove the (DAB) (A).

|
| 4. |
Disconnect the DAB connector (A) and horn connector (B).

|
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedure.
|
|
| 1. |
Install in the reverse order of removal.
|
When installing the Driver Airbag (DAB) to the steering wheel, make sure that the airbag wire is
not caught in the steering wheel's internal structure.
|
|
| 2. |
Check the airbag system and horn operate normally.
|
When POWER ON, the airbag warning light should turns off after turning on for 3 - 6 seconds.
|
|
Passenger Airbag (PAB) Troubleshooting
|
Direct measuring the resistance of the airbag is very dangerous as it can cause the airbag deployment.
|

Passenger Airbag (PAB) Removal and Installation
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
| 1. |
Remove the crash pad assembly.
(Refer to Body - "Crash Pad Assembly")
|
| 2. |
Remove the Passenger Airbag (PAB) (A) after removing the bolts.
Tightening torque :
3.9 - 5.9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)
|
|
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
| 1. |
Install in the reverse order of removal.
|
Be sure to keep the torque specifications presented in shop manuals. Otherwise, it could lead to
the malfunction of airbag system.
|
|
| 2. |
Check that the airbag system operates normally.
|
When POWER ON, the airbag warning light should turns off after turning on for 3 - 6 seconds.
|
|
Side Airbag (SAB) Troubleshooting
|
Direct measuring the resistance of the airbag is very dangerous as it can cause the airbag deployment.
|

Side Airbag (SAB) Removal and Installation
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
|
When replacing the airbag due to a deployment of the airbag, replace the seat bag assembly.
|
|
The indication below represents the location of a clip or fastener.

|
Front Side Airbag (SAB)
| 1. |
Remove the front seat back cover assembly.
(Refer to Body - "Front Seat Back Cover Assembly")
|
| 2. |
Separate the Side Airbag (SAB) after removing the nuts (A).
Tightening Torque :
5.9 - 7.8 N·m (0.6 - 0.8 kgf·m, 4.3 - 5.8 lb·ft, 52.1 - 69.4 lb·in)
|

|
| 3. |
Remove the SAB (A) after removing the fasteners.

|
Rear Side Airbag (SAB)
| 1. |
Remove the rear seat back cover assembly.
(Refer to Body - "Rear Seat Back Cover Assembly")
|
| 2. |
Separate the SAB connector (A).

|
| 3. |
Remove the SAB (A) after removing the nuts.
Tightening Torque :
5.9 - 7.8 N·m (0.6 - 0.8 kgf·m, 4.3 - 5.8 lb·ft, 52.1 - 69.4 lb·in)
|

|
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
| 1. |
Install in the reverse order of removal.
|
•
|
Be sure to keep the torque specifications presented in shop manuals. Otherwise, it could
lead to the malfunction of airbag system.
|
|
•
|
Since improper installation of the front seat back cover will prevent the normal deployment
of the side airbags, make sure that the front seat back cover is properly installed.
|
|
|
| 2. |
Check that the airbag system operates normally.
|
When POWER ON, the airbag warning light should turns off after turning on for 3 - 6 seconds.
|
|
Other information:
Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: LCD display modes
View
Description
Driving Assist view
Displays information related to Kia EV6 driver assistance and safety systems.
Navigation view
Displays navigation guidance, route information, and map-related details.
Utility information view
Displays driving information, warnings, energy economy data, and additional vehicle status
information.
Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Brake bleeding
Special Service Tool
Tool Name / Number
Illustration
Description
Air bleeding tool0K580 - 3D100
Used for brake bleeding (regulating pressure)(Used with 0K585 - E8100)
Air bleeding tool adaptor0K585 - E8100
Used for brake bleeding (reservoir cap adapter)(Used with 0K580 - 3D100)
Integrated Electronic Brake (IEB) System Air Bleeding procedures
•
Do not reuse the drained brake fluid.

Contents
Categories