Kia EV6: Body (Interior / Exterior / Electrical) / Security & Vehicle Ignition System
Contents:
Body Domain Control Unit Description and Operation
| Description and Operation |
Body Domain Control Unit (BDC)
The body domain control unit is a unit that integrates functions such as a body control module (BCM), a smart key
unit (SMK), a tire pressure monitoring system (TPMS), and an immobilizer.
| 1. |
Body Control Module Functions
Burglar Alarm
|
Tailgate Burglar Alarm
|
Issues an alarm depending on the tailgate operation.
|
Panic Alarm
|
Generates warning sound and displays flasher lamp (horn & flasher) depending on the panic
signal.
|
Security Lamp Control
|
Controls security lamp in vehicle alert status.
|
External Lamp
|
Tail Lamp
|
Turns on / off the tail lamp automatically. It also turns off the tail lamp
automatically when the driver forgot to turn off the lamp switch.
|
Auto Light
|
Turns on/off the tail lamp and headlamp automatically depending on whether it is day or night when the
headlamp switch is placed at Auto.
|
Welcome Light
|
The welcome light function turns on the headlamp and tail lamp for 15 seconds when an unlock signal is
detected while vehicle door is locked.
|
Escort Function
|
Turns on the escort lamp when the power is turned off while the headlamp is on.
|
–
|
It turns on the headlamp and maintains the state for 20 minutes if POWER is turned off
while the headlamp is on.
|
|
–
|
The headlamp remains on only for 30 seconds when the driver seat door is opened and closed
during the 20 minute period.
|
|
–
|
The headlamp turns off when remote control lock button is pressed twice while the headlamp
is on.
|
|
Headlamp (Low Beam / High Beam)
|
Controls high beam / low beam depending on the headlamp switch (multifunction switch).
|
Daytime Driving Light Control
|
Controls the daytime driving light lamp depending on the conditions at the time of vehicle start.
|
Telematics (MTS)
|
MTS Alarm Control
|
Controls the output of the door lock/unlock/remote start/panic function in
response to the signal transmitted by the MTS unit
|
Front / Rear Parking Assist (PDW)
|
PDW Display
|
Receives a signal from parking assist sensor through LIN communication and
displays it on the instrument cluster.
|
PDW Warning
|
Detects obstacles in front and rear sides using the ultrasonic sensor (PDW) in the case of gear range
("R" or "D") and issues a warning if there is an obstacle.
|
Warning
|
Seat Belt Reminder and Indicator Lamp
|
Issues a warning if the seat belt is not fastened, and prevents pattern
activation if the vehicle is driven while the seat belt is not fastened.
|
Key Reminder Warning
|
Issues a warning if the driver seat door is open while ACC is on.
|
Key Reminder Warning
|
Issues a warning if the driver seat door is open while POWER is on.
|
Sunroof Open Warning
|
Alarm output function when getting out of the car by removing the key while the sunroof is open
|
Wiper and Washer
|
Wiper (Low / High / Mist / Auto)
|
Controls wiper operating power and fail-safe circuit.
|
Wiper
|
Control the washer interlocking wiper.
|
|
| 2. |
Smart Key Unit Functions
SMK
|
Door Lock and Unlock
|
Locks/Unlocks the door based on the door unlock signal and the signal from push
buttons on the driver's / passenger's side outside handles.
|
SMK Welcome Light
|
Controls door mirror and puddle lamp after smart key authentication when the driver with smart key
approaches the vehicle.
|
Power Tailgate
|
When holding a smart key and staying in the rear bumper (in the LF antenna area) for more than 3
seconds, the power tailgate opening function is performed.
|
SMK Warning
|
Key Reminder 1
|
When the driver attempts to lock the door, it checks if there is a smart key
inside the vehicle and unlocks the door if there is one.
|
Key Reminder 2
|
Checks the door lock status for 0.5 seconds after the vehicle door is closed and unlocks the door and
generates a warning sound using the external buzzer if the door is locked.
|
Door Lock Warning 1
|
Generates a warning sound with the external buzzer if the driver tries to leave the vehicle while POWER
ON.
|
Door Lock Warning 2
|
Generates a warning sound with the external buzzer if the driver tries to lock the door and leave the
vehicle while one or more doors are open.
|
Door Lock Warning 3
|
Searches for a smart key inside the vehicle when the driver tries to lock the door, and issues a warning
and does not lock the door if there is a smart key inside.
|
Key Out Lamp Warning
|
If the vehicle moves at 3 km/h or less while POWER ON and the door is open, it searches for the smart
key every 3 seconds and blinks the warning lamp if there is no smart key.
|
SMK RKE (Remote Keyless Entry)
|
Door Lock / Unlock
|
Locks/Unlocks the door based on the door unlock signal and the signal from push buttons on the
driver's / passenger's side outside handles.
|
Panic
|
Performs vehicle panic and panic stop functions based on the panic button signal.
|
Engine Start
|
Start stop button (SSB), immobilizer, start relay power control, SSB Lamp Control.
|
|
| 3. |
Tire Pressure Monitoring System (TPMS) Functions
Tire pressure monitoring system continuously monitors pressure and temperature inside the tire in order to
warn the driver of the changes in tire pressure that may have influence on vehicle driving conditions. TPMS
control module analyzes the data from the WE (Wheel Electronic) sensor attached inside each wheel and
determines the tire conditions and generates a signal that is necessary for warning lamp control.
|
| 4. |
Identity Authentication Unit (IAU) Function
The IAU receives the encrypted digital key value from the smartphone, decrypts it, analyzes it, and
delivers the authentication result to the BDC.
|
Body Domain Control Unit On Vehicle Inspection
| 1. |
The Body Domain Control unit (BDC) can quickly diagnosed for problems with the KDS (Refer to "DTC
guide").
| (1)
|
Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS.
(Refer to DTC guide when fault code is found.)
|
| (2)
|
S/W Management : Controlling other features including system option setting and zero point
adjustment.
(S/W Management → BDC-BCM → Variant Coding)
(S/W Management → BDC-SMK → Smart Key Code Saving)
(S/W Management → BDC-TPMS → ID Writing)
(S/W Management → BDC-IAU → Status Information)
(S/W Management → BDC-IAU → Learning Mode)
(S/W Management → BDC-IAU → IAU Neutralization Mode)
(S/W Management → BDC-IAU → Activate Card Key Registration Mode)
|
|
Refer to the KDS screen for operating conditions and details
|
|
Body Domain Control Unit Removal and Installation
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedure.
|
|
| 1. |
Perform the order below with the KDS before removing the Body Domain Control unit (BDC).
(S/W Management → Connected Car Navigation Cockpit → AVN-FPM Neutralization Mode)
(S/W Management → BDC-IAU → IAU Neutralization Mode)
|
Refer to the KDS screen for operating conditions and details.
|
|
| 2. |
Remove the crash pad assembly.
(Refer to Crash Pad - "Crash Pad Assembly")
|
| 3. |
Separate the body domain control unit (A) after removing the bolts and nut.
Tightening torque :
7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)
|
|
| 4. |
Remove the unit (A) after disconnecting the connector (B).
|
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedure.
|
|
| 1. |
Install in the reverse order of removal.
|
| 2. |
Perform the order below with the KDS when replacing the body domain control unit.
(S/W Management → BDC-BCM → Variant Coding)
(S/W Management → BDC-SMK → Smart Key Code Saving)
(S/W Management → BDC-TPMS → ID Writing)
(S/W Management → Connected Car Navigation Cockpit → AVN-FPM Learning Mode)
(S/W Management → BDC-IAU → Learning Mode)
|
Refer to the KDS screen for operating conditions and details.
|
|
| 3. |
Perform Over The Air (OTA) controller S/W update with KDS.
(Refer to Security & Vehicle Ignition System - "Over The Air
(OTA)")
|
System characteristics :
|
–
|
Changing the state of power by using the start button.
|
|
–
|
Controlling external relays for POWER ON / DRIVE READY terminal switching and STARTER, without use of
mechanical IG switch.
|
|
–
|
Indicating the vehicle status on cluster by displaying messages.
|
|
–
|
Immobilizer function by LF transponder communication between between fob and button start switch.
|
|
–
|
Interface with Low Speed CAN vehicle communication network.
|
|
–
|
Interface with LIN vehicle communication network depending on platform.
|
System Main Function
|
•
|
Switching of POWER ON / DRIVE READY terminal.
|
|
•
|
Control of the STARTER relay based on communication with Vehicle Control Unit (VCU).
|
|
•
|
Management of the Immobilizer function.
|
|
•
|
Management of Button Start System warning function.
|
Wireless Communications
The electric signal is used to exchange information between vehicle and FOB key. For now, button start is applied
with smart key FOB key together.
Smart key function is explained separately so refer to the corresponding system contents.
System Flow Chart
Schematic Diagram
Body Domain Control Unit (BDC)
Body domain control unit function :
|
–
|
Start/Stop Button (SSB) control
|
|
–
|
Immobilizer communication (with VCU for releasing immobilizer)
|
|
–
|
Authentication server (Validity of Transponder and in case of Smart Key option Passive FOB authentication)
|
|
–
|
System consistency monitoring
|
|
–
|
Control of display message / warning buzzer
|
Limp Home Mode
|
–
|
In case of no input signal for the brake switch, the POWER OFF mode shall cycle to “START” by pressing SSB
for more than 10 seconds.
|
|
–
|
In case of problems with communication between VCU and CAN (the VCU state), the “START” state cycles to the
“EV Ready” based on rpm input.
|
|
–
|
In case that one out of two SSB input lines is disconnected, the electric power cycling is available when
SSB is pressed twice within 10 seconds.
The buzzer rings when the button is pressed for the first time.
Electric power cycling is available and buzzer stops when the button is pressed twice within 10 seconds.
|
Terminal and Starter Relay
Relay is used to switch the terminal POWER ON / DRIVE READY.
Normally-open relay is operated by smart key unit.
One relay coil is connected to output terminal of IBU.
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
| 1. |
Remove the Start/Stop Button (SSB).
(Refer to Floor Console - "Console Upper Cover")
|
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
| 1. |
Install in the reverse order of removal.
|
Central Communication Unit (CCU) On Vehicle Inspection
| 1. |
The central communication unit (CCU) can be quickly diagnosed for problems with the KDS. (Refer to
"DTC guide")
| (1)
|
Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS.
(Refer to DTC guide when fault code is found.)
|
| (2)
|
S/W Management : Controlling other features including system option setting and zero point
adjustment.
(S/W Management → Central Communication Unit (CCNF) → Variant Coding)
(S/W Management → Central Communication Unit (CCNF) → OTA Initialization)
|
|
Refer to the KDS screen for operating conditions and details
|
|
Central Communication Unit (CCU) Removal and Installation
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedure.
|
|
| 1. |
Remove the crash pad lower panel.
(Refer to Crash Pad - "Crash Pad Panel")
|
| 2. |
Lower the steering column after removing the nuts and through-bolt.
(Refer to Steering System - "MDPS Column and Housing")
|
| 3. |
Separate the central communication unit (CCU) (A) after removing the bolts.
Tightening torque :
6.9 - 10.8 N·m (0.7 - 1.1 kgf·m, 5.1 - 8.0 lb·ft)
|
|
| 4. |
Remove the CCU (A) after disconnecting the connectors (B).
|
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedure.
|
|
| 1. |
Install in the reverse order of removal.
|
| 2. |
Perform the order below with the KDS when replacing the Central Communication Unit (CCU).
(S/W Management → Central Communication Unit (CCNF) → Variant Coding)
|
Refer to the KDS screen for operating conditions and details
|
|
| 3. |
Perform Over The Air (OTA) controller S/W update with KDS.
(Refer to Security & Vehicle Ignition System - "Over The Air
(OTA)")
|
Data Connectivity Unit (DCU) On Vehicle Inspection
| 1. |
The Data Connectivity Unit (DCU) can be quickly diagnosed for problems with the KDS. (Refer to "DTC
guide")
| (1)
|
Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS.
(Refer to DTC guide when fault code is found.)
|
|
Refer to the KDS screen for operating conditions and details
|
|
Data Connectivity Unit (DCU) Removal and Installation
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
| 1. |
Remove the center crash pad panel.
(Refer to Crash Pad - "Crash Pad Panel")
|
| 2. |
Separate the Data Connectivity Unit (DCU) (A) after disconnecting the DCU connector (B).
|
| 3. |
Remove the DCU (A) after removing the nuts.
Tightening torque :
7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)
|
|
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
| 1. |
Install in the reverse order of removal.
|
| 2. |
When replacing the Data Connectivity Unit (DCU), perform Over The Air (OTA) controller S/W update with KDS.
(Refer to Security & Vehicle Ignition System - "Over The Air
(OTA)")
|
Digital Key System On Vehicle Inspection
| 1. |
The digital key system can quickly diagnosed for problems with the KDS. (Refer to "DTC guide")
| (1)
|
Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS.
(Refer to DTC guide when fault code is found.)
|
| (2)
|
S/W Management : Controlling other features including system option setting and zero point
adjustment.
|
|
Refer to the KDS screen for operating conditions and details
|
|
Digital Key System Description and Operation
Digital key system allows a driver to lock or unlock the vehicle doors with smartphone app or a NFC key card
without a smart key.
| Main features of digital key system |
|
–
|
A smartphone key can be issued from the digital key server and a NFC key card can be registered through a
separate process.
|
|
–
|
The smartphone key can be registered through the ccNC screen of the vehicle by downloading the app after
registering as a member on the Kia website.
|
|
–
|
The NFC card key can be registered through the ccNC screen of the vehicle after going through a separate
authentication process.
(The separate authentication procedure is available with the digital key app or selecting “Card key
registration mode activation” using the KDS.)
|
|
–
|
3 drivers can share a smartphone key at maximum but one NFC key card is provided.
|
|
–
|
When registering a smartphone key or an NFC card key, the user must possess the smart key, and after
registration, door lock/unlock and start functions can be performed without carrying the smart key.
|
|
–
|
If a smartphone is set up in the driver's profile (Profile 1, Profile 2, Guest) through the ccNC
screen, the driver is automatically recognized when the door is unlocked and the personal preference function
(IMS, ccNC, etc.) is executed.
|
|
–
|
Vehicle status information (mileage, fuel economy, battery level, etc.) can be checked on the smartphone
app.
|
|
–
|
When you delete the smartphone key or NFC key card, you should have the smart key.
(Smartphone key or NFC key card is not required to carry to delete.)
|
|
•
|
Register a smartphone key or NFC key card using the registration process below.
Smartphone Key/NFC Key Card Registration Process
Step
|
1. Sign up for membership
|
2. Install App & Login
|
3. Key Registration
|
4. Entry/Start
|
5. Key Sharing
|
Description
|
Create an account on the Kia membership website
|
Install the Kia Connect APP on your smartphone and login
|
Get in the car with the FOB key and register the smartphone and the NFC card key
|
NFC door lock/unlock, NFC vehicle start, remote control via APP
|
Digital key can be shared with others with the APP
|
|
|
Digital Key System NFC Key Card Registration
| NFC Key Card Registration Process |
The digital key system provides an NFC key card for emergency purposes, such as when a smartphone cannot be
delivered directly, such as valet parking, or when the smartphone battery is off.
The card key must be registered in the vehicle for the first time after the vehicle is shipped or the first time
after replacing the BDC to be used.
NFC Key Card Registration Process
You should follow the steps in the procedure below to register NFC key card.
| 1. |
Make the vehicle enable to register NFC key card.
|

It can be registered with KDS - S/W Management - "Card Key Registration Mode
Activation".
|
|

It also can be registered digital key app available in the vehicle.
|
|
|
| 2. |
You should register the NFC key card on AVNT or the cluster within 5 minutes after getting in the vehicle.
|
•
|
When there is a previously enrolled NFC key card, the “Enroll” button on the User’s
Settings menu is deactivated so press “Deletion” button to delete the NFC key card and
register new one. (You should have your smart key to delete in the vehicle)
|
|
•
|
A NFC key card can be registered and deleted repeatedly but if you enroll a new NFC key
card, the previously enrolled key is not available.
|
|
•
|
When replacing the BDC-IAU (authentication controller), the previously used NFC card key
cannot be used.
|
|
•
|
iPhone users and non-smartphone users can register the NFC card key with KDS - S/W
Management - "Card Key Registration Mode Activation".
|
|
•
|
You should register the NFC key card in the vehicle within 5 minutes after proceeding
authentication process.
|
|
•
|
If the enrollment process fails to be completed within 5 minutes, you should retry after
re-processing the authentication.
|
|
|
NFC Key Card Registration by using the KDS.
| 1. |
Perform the "Card Key Registration Mode Activation" by using the KDS.
(S/W Management → BDC-IAU → Card Key Registration Mode Activation)
|
Refer to the KDS screen for operating conditions and details
|
|
| 2. |
After placing the card key on the NFC wireless charger, register the card key on the ccNC screen.
|
•
|
You should get in the vehicle within 5 minutes and register the key card After completing
“Key Card Enroll Mode” by using the KDS.
|
|
•
|
When you register a NFC key card, the smart key should be in the vehicle.
|
|
|
| 3. |
Place the NFC key card that you want to register on the interior authentication pad (Wireless charger) to
complete the process.
|
Digital Key System Digital Key System Inspection
Digital Key System Operation Verification
| 1. |
When the digital key system failure occurs, the system operation should be confirmed as below.
| (1)
|
Checked the lock/unlock operation by touching the NFC antenna portion of the door handle with a
smart phone or NFC card key.
|
| (2)
|
Check whether the start-up is working or not after placing your smart phone or key card on the
wireless charger.
|
| (3)
|
Make sure confirm whether BLE lock or unlock are operable with the smart phone.
|
| (4)
|
If there is an abnormality in the operation of the digital key system, the inspection is performed
according to the "Digital Key System A/S procedure" below.
|
|
Digital Key System A/S Procedure
|
•
|
To inspect the digital key, vehicle owner’s smart phone or NFC card key is required. If you do not
have both of those, you should register new NFC card key and complete the test before delivering the
vehicle.
|
|
•
|
Once a new NFC key card is registered, the existing NFC key card is not available.
|
|
Inspection 1 :
Check whether the door handles of driver’s seat and passenger’s seats work properly. If the door
handle of the driver’s seat fails to operate, the handle should be checked after replacing with
passenger’s seat door handle.
If it works properly, only the door handles of driver’s seat should be replaced since it does not
have problem with wiring.
If both of those handles do not work, the door handles of driver’s seat and passenger’s seat should
be replaced with a new handle to check whether it works properly.
If it performs normally, the handle should be replaced with a new one. However, there is a
malfunction in the part, you assume (B166D00 driver’s seat door handle malfunction) or (B166E00
passenger’s seat door handle malfunction) occurs and process inspections in accordance with “DTC
Diagnosis Guide”.
|
|
Inspection 2 :
Check whether the tart-up with the digital key (smart phone or card key) after replacing with new
wireless charger.
If it works properly, the vehicle can be delivered with the function on since it does not have a
problem with wiring.
If it does not work even after replacing with a new product, the wireless charger wiring should be
checked.
|
|
Inspection 3 :
After replacing with a new BLE module, check whether the digital key works.
If it does not work even after replacing with a new product, the wireless charger wiring should be
checked.
If there is not a problem with wiring, we assume (B165A00 BLE module malfunction), (B167F00 LIN
communication failure between IAU and BLE modules) occurs and process inspections in accordance with
“DTC Diagnosis Guide”.
|
|
Inspection 4 :
Process above “Inspection 1” and “Inspection 2” in order.
|
|
Inspection 5 :
Process above “Inspection 1” and “Inspection 3” in order.
|
|
Inspection 6 :
Process above “Inspection 1” and “Inspection 3” in order.
|
|
Inspection 7 :
If it operates without any problem after processing from No.1 to No.3 with the digital key, the
vehicle can be delivered with the function on since it does not have a problem with wiring.
If it does not work, assume that (B165C00 IAU-BDC learning anomaly) has occurred and perform a
check according to the "DTC Guide".
If still does not operate, “Inspection 1”, “Inspection 2”and “Inspection 3” should be processes in
order.
If any one of the three works normally, check the wiring of the remaining cases, and if all three
do not work, replace the BDC with a new one and perform "EMS/FOB learning" and "IAU-BDC
learning".
Since the BDC has been replaced with a new one, perform "Check 1", "Check 2",
and "Check 3" in order to check the system operation.
|
|
IAU-BDC learning status inspection
|
Digital key function works only when the learning states of IAU and BDC are learnt.
|
| 1. |
Perform the "Status Information" procedure by using the KDS.
(S/W Management → BDC-IAU → IAU Status Information)
|
Refer to the KDS screen for operating conditions and details
|
Mark
|
Description
|
Learning status
|
Virgin
|
Initial state
|
Non-learning state
|
Learnt
|
Learning completiond state
|
Learning completiond state
|
Neutralized
|
Neutral state
|
Non-learning state
|
|
Smartphone Key Registration Status Inspection
|
Smart phone key registration status can be checked via "Data Analysis".
|
| 1. |
Connect KDS to vehicle.
|
| 2. |
Select the "Data Analysis" and "IAU".
Mark
|
Description
|
Owner's smartphone registration state
|
0 : Main user's smart phone is not registered.
|
1 : Main user's smart phone is registered.
|
Number of currently registered digital key (smartphones)
|
0 : No registered phone.
|
1-4 : Currently registered device number.
|
|
NFC Key Card registration status Inspection
|
Smart phone key registration status can be checked via "Data Analysis".
|
| 1. |
Connect KDS to vehicle.
|
| 2. |
Select the "Data Analysis" and "IAU".
Mark
|
Description
|
Number of currently registered digital key (card key)
|
0 : No registered card.
|
1 : registered 1 card.
|
|
Digital Key System Removal and Installation
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
Ultra Wideband Unit [Front Bumper Side]
| 1. |
Remove the front bumper assembly.
(Refer to Front & Rear Bumper - "Front Bumper
Assembly")
|
| 2. |
Disconnect the unit connector (A).
|
| 3. |
Remove the unit (A).
|
|
Clip position :
|
Ultra Wideband Unit [Rear Bumper Side]
| 1. |
Remove the rear bumper assembly.
(Refer to Front & Rear Bumper - "Rear Bumper
Assembly")
|
| 2. |
Disconnect the unit connector (A).
|
| 3. |
Remove the unit (A).
|
|
Clip position :
|
Ultra Wideband and BLE Unit
| 1. |
Remove the roof trim assembly.
(Refer to Roof Trim - "Roof Trim Assembly")
|
| 2. |
Disconnect the unit connector (A).
[Master]
[Slave]
|
| 3. |
Remove the unit (A).
[Master]
[Slave]
|
Clip position :
|
|
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
| 1. |
Install in the reverse order of removal.
|
| 2. |
When replacing the ultra-wideband and BLE unit, perform Over The Air (OTA) controller S/W update with KDS.
(Refer to Security & Vehicle Ignition System - "Over The Air
(OTA)")
|
Fingerprint Authentication System Description and Operation. Fingerprint Authentication System Troubleshooting
Fingerprint Authentication System Description and Operation
| Description and Operation |
The fingerprint authentication system recognizes a user with a registered fingerprint and provides the convenience
of starting a vehicle without a smart key or making electronic payments without entering a password.
Major Features of the Fingerprint Recognition System
|
–
|
AVN link: Reinforcing driver convenience and security such as personalization, profile lock & unlock,
electronic payment and valet parking mode using pre-registered fingerprint information.
|
|
–
|
Engine start: Start the engine and drive with pre-registered fingerprint information.
|
Fingerprint Authentication System Troubleshooting
Fingerprint Authentication System On Vehicle Inspection
| 1. |
The fingerprint authentication system can quickly diagnosed for problems with the KDS (Refer to "DTC
guide").
| (1)
|
Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS.
(Refer to DTC guide when fault code is found.)
|
| (2)
|
S/W Management : Controlling other features including system option setting and zero point
adjustment.
(S/W Management → Fingerprint Recognition Module → Status Information)
(S/W Management → Fingerprint Recognition Module → FPM Self-Diagnosis Test)
(S/W Management → Fingerprint Recognition Module → Check Registered Fingerprint Status)
(S/W Management → Fingerprint Recognition Module → Fingerprint Sensor Contact Inspection)
|
|
Refer to the KDS screen for operating conditions and details
|
|
Fingerprint Authentication System Removal and Installation
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedure.
|
|
| 1. |
Perform the order below with the KDS before removing the fingerprint recognition unit.
(S/W Management → Connected Car Navigation Cockpit → AVN-FPM Neutralization Mode)
(S/W Management → BDC-IAU → IAU Neutralization Mode)
|
Refer to the KDS screen for operating conditions and details.
|
|
| 2. |
Remove the fingerprint recognition unit.
(Refer to Floor Console - "Console Upper Cover")
|
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedure.
|
|
| 1. |
Install in the reverse order of removal.
|
| 2. |
Perform the order below with the KDS when replacing the fingerprint recognition unit.
(S/W Management → BDC-IAU → Learning Mode)
(S/W Management → Connected Car Navigation Cockpit → AVN-FPM Learning Mode)
|
Refer to the KDS screen for operating conditions and details.
|
|
| 3. |
Perform Over The Air (OTA) controller S/W update with KDS.
(Refer to Security & Vehicle Ignition System - "Over The Air
(OTA)")
|
Junction Block On Vehicle Inspection
| 1. |
PowerNet domain controllers can quickly diagnosed for problems with KDS. (Refer to "DTC Guide")
| (1)
|
Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS.
(Refer to DTC guide when fault code is found.)
|
| (2)
|
S/W Management : Controlling other features including system option setting and zero point
adjustment.
(S/W Management → Powernet Domain Controller → Variant Coding)
(S/W Management → Powernet Domain Controller → Mode Setting)
|
|
Refer to the KDS screen for operating conditions and details
|
|
Junction Block Inspection
Power Relay Inspection (Type A)
Check for continuity between the terminals.
| 1. |
After supplying power between terminal No. 85 and 86, check that there is continuity between terminal No.
30 and 87.
|
| 2. |
After supplying power between terminal No. 85 and 86, check that there is no continuity between terminal
No. 30 and 87.
Terminal
|
Operate
|
Power ON
|
Power OFF
|
30 - 87
|
Continuity
|
-
|
|
Power Relay (Type B)
Check for continuity between the terminals.
| 1. |
After supplying power between terminal No. 86 and 85, check that there is continuity between terminal No.
87 and 30.
|
| 2. |
After supplying power between terminal No. 86 and 85, check that there is no continuity between terminal
No. 87 and 30.
Terminal
|
Operate
|
Power ON
|
Power OFF
|
30 - 87
|
Continuity
|
-
|
|
Fuse
| 1. |
Check for separation of fuse holder and check that the holder is tightly holding the fuse.
|
| 2. |
Check that each fuse circuit has the exact fuse capacity.
|
| 3. |
Check the fuses for any damage.
|
If a fuse is to be replaced, be sure to use a new fuse of the same capacity.
|
|
Multi-Fuse
| 1. |
Disconnect the battery negative ( - ) terminal and the high voltage service interlock connector.
(Refer to Battery Control System - "Auxiliary 12 V Battery -
2WD")
(Refer to Battery Control System - "Auxiliary 12 V Battery -
4WD")
|
| 2. |
Remove the multi fuse (A) in the direction of the arrow after removing the nut.
|
| 3. |
Remove the multi-fuse (A) by pulling it in the direction of the arrow.
|
| 4. |
Remove the multi fuse (A) in the direction of the arrow after removing the nut.
|
| 5. |
Check the multi-fuses for any damage.
|
Use the multi-fuse of the correct fuse specification.
|
|
Junction Block Removal and Installation
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
PCB Block
| 1. |
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage
service interlock connector.
| (1)
|
Open the front trunk (A).
|
| (2)
|
Open the auxiliary 12 V battery service cover (A).
|
| (3)
|
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).
Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)
|
|
| (4)
|
Disconnect the service interlock connector (A).
|
•
|
Wait more than 5 minutes for capacitor of the high voltage battery system to be
discharged completely.
|
|
•
|
When working on a vehicle during discharging the capacitor, it can cause an
electrical shock or injury, so follow the manual.
|
|
|
The service interlock connector cannot be completely removed.
|
|
|
| 2. |
Remove the PCB block (A) after pushing the mounting hooks in the direction of the arrow.
|
| 3. |
Disconnect the PCB block connector (A).
|
Powernet Domain Controller
| 1. |
Remove the crash pad lower panel.
(Refer to Crash Pad - "Crash Pad Panel")
|
| 2. |
Disconnect the powernet domain controller connectors (A).
|
| 3. |
Separate the powernet domain controller (A) after removing the nuts.
Tightening torque :
6.9 - 10.8 N·m (0.7 - 1.1 kgf·m, 5.1 - 8.0 lb·ft)
|
|
| 4. |
Remove the powernet domain controller (A) after disconnecting the connectors (B).
|
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
| 1. |
Install in the reverse order of removal.
|
| 2. |
Perform the order below with the KDS when replacing the Powernet domain controller.
(S/W Management → Powernet Domain Controller → Variant Coding)
|
Refer to the KDS screen for operating conditions and details
|
|
| 3. |
When replacing PowerNet domain controller, Perform Over The Air (OTA) controller S/W update with KDS.
(Refer to Security & Vehicle Ignition System - "Over The Air
(OTA)")
|
Over The Air (OTA) Description and Operation. Over The Air (OTA) OTA Update Sequence
Over The Air (OTA) Description and Operation
| Description and Operation |
|
•
|
OTA (Over The Air) is a function that wirelessly updates the vehicle's controller software.
|
|
•
|
It provides a service that enables direct wireless communication to update the electronic control unit
software, which was only possible by visiting a service center.
|
OTA System Flow Chart
Over The Air (OTA) OTA Update Sequence
|
•
|
OTA update downloads S/W wirelessly while driving and updates after turning off the vehicle.
|
|
•
|
Updates are performed in the following order.
|
|
| 1. |
After stopping the vehicle, turn off the vehicle and update in order when the update approval information
is displayed.
|
| 2. |
After restarting the vehicle, the update information message is displayed.
|
When update fails, check "Part No" and "S/W version" with KDS and try again.
(Refer to Over The Air (OTA) - "On Vehicle
Inspection")
|
|
Over The Air (OTA) On Vehicle Inspection
OTA target controller
|
•
|
When replacing the OTA target controller, check the S/W version with KDS.
|
|
•
|
If the S/W version of the replaced controller is higher or lower than other controller versions,
OTA automatic update is not possible.
|
|
No.
|
Controller
|
Detail
|
1
|
ACU
|
Airbag Control Unit
|
2
|
ADAS_DRV
|
ADAS DRIVING ECU
|
3
|
ADAS_PRK
|
ADAS PARKING ECU
|
4
|
ADP
|
Acoustic Design Processor
|
5
|
ATCU
|
Auto Temperature Control Unit
|
6
|
BDC
|
Body Domain Controller
|
7
|
BLTN_CAM
|
Built-in Cam
|
8
|
BMS
|
Battery Management System
|
9
|
ccNC
|
Connected Car Navigation Cockpit
|
10
|
CCU
|
Cental Communication Unit
|
11
|
CLU
|
Cluster
|
12
|
DCU
|
Data Connectivity Unit
|
13
|
ECS
|
Electronic Controlled Suspension
|
14
|
eLSD
|
Electronic Limited Slip Differential
|
15
|
ETCS
|
Electronic Toll Collection System
|
16
|
EXT AMP
|
external AMPlifier
|
17
|
FPM
|
FingerPrint Module
|
18
|
HOD
|
Hand of Detection
|
19
|
HUD
|
Head Up display
|
20
|
ICC
|
In Cabin Camera
|
21
|
ICCU
|
Integrated Charging Control Unit
|
22
|
IEB
|
Intergrated Electronic Booster
|
23
|
MCU (INVERTER)
|
Motor Control Unit
|
24
|
MDPS
|
Motor Driven Power Steering
|
25
|
MKBD
|
Multimedia Keyboard
|
26
|
MLM
|
Mood Lamp Module
|
27
|
PDC
|
Powernet Domain Controller
|
28
|
PSM
|
UNIT ASSY-MEMORY POWER SEAT
|
29
|
PSU
|
Power Seat Unit
|
30
|
PTGM
|
Power Tailgate Module
|
31
|
SBCM
|
Side Body Control Module
|
32
|
SBW-SHIFTER
|
SBW-SHIFTER
|
33
|
SCU
|
SBW Control Unit
|
34
|
SHVU
|
Seat Heater&Ventilation Unit
|
35
|
UWB_BLE
|
Ultra Wideband & Bluetooth Low Energy
|
36
|
VCMS
|
Vehicle Charging Management System
|
37
|
VCU
|
Vehicle Control Unit
|
38
|
VESS
|
Virtual Engine Sound System
|
39
|
WPC
|
UNIT ASSY-WIRELESS CHARGING
|
Over The Air (OTA) Controller S/W Update
| 1. |
Perform OTA management version update with the KDS.
|
| 2. |
Turn off the vehicle and connect the KDS.
|
| 3. |
Enter the service inspection mode.
(Refer to Body (Interior / Exterior / Electrical) - "Service
Inspection Mode")
|
| 4. |
Select "Car Model" and select "ECU Upgrade".
|
| 5. |
Select “OTA Management Version Update”.
|
•
|
It is possible to enter OTA management version update without VCI 2 or ECI cable, but the
entry and update time may become longer.
|
|
•
|
Ethernet communication controller requires a dedicated cable connection for OTA management
version update.
|
|
–
|
VCI 2: ECI module set for VCI 2
|
|
–
|
VCI 3: Ethernet Cable for VCI 3
|
|
|
| 6. |
Update by checking the "Part No" and "S/W version" of the controller.
|
•
|
All active buttons must be updated. (Switch to inactive when update is complete)
|
|
•
|
Manual Update Precautions
Before work, check if the controller is installed on the vehicle, and if it is installed,
check the Part No. and perform the update. (Prevention of erroneous specification update)
|
|
•
|
Conditions for activating the manual update button
|
| 1) |
Unable to read controller information (controller no response or negative response)
|
| 2) |
Controller not mounted on vehicle
|
|
•
|
Conditions for activating the auto update button
|
| 1) |
Matching Part No. (same specifications)
|
| 2) |
Vehicle S/W version and OTA latest S/W version mismatch (update required)
|
|
|
※ Automatic update procedure
Displays controller name, Part No, and S/W version information during auto update
|
|
※ Manual update procedure
In a situation, it is difficult to check the controller specification through KDS, check the Part
No. of the vehicle controller directly,
Perform an update after checking that it is the same as Part No. in the pop-up
|
|
| 7. |
Data download and reprogramming are in progress.
|
| 8. |
When the update is completed, the activated update button is inactivated and the list is updated with
completion.
|
| 9. |
When the update fails, recheck the OTA management version update function entry conditions and Part No.
|
When the update is complete, restart the vehicle, wait for 5 minutes, and check if there is no S/W
ver error pop-up displayed in ccNC.
|
|
ROA (Rear Occupant Alert) System Description and Operation
The system detects the passenger in the vehicle and prevents the driver from getting off the vehicle with the
passenger in the back.
Order of Operation
Sensor Detection
|
Sensing Control
|
Radar Sensing
|
Warning Control
|
Warning
|
Driver's door switch Rear door switch
|
Body Domain Control Unit (BDC)
|
Rear Occupant Alert (ROA) Unit
|
Body Domain Control Unit (BDC)
|
Cluster pop-up and voice guidance
|
Horn + Hazard lamp
|
Kia Connect warning
|
|
–
|
1st warning : If you open the driver's door after you open and then close the rear door and POWER OFF,
the system provides warning by showing message on the cluster and giving voice instruction.
|
| 1) |
The system detects the indoor movement using the rear occupant alert sensor installed on the roof trim when
the driver gets off the vehicle and locks all the doors.
|
| 2) |
If any movement inside the vehicle is detected, horn is activated for 25 seconds and the mobile text
message is sent. (If Kia Connect equipped)
|
ROA (Rear Occupant Alert) System On Vehicle Inspection
| 1. |
The Rear Occupant Alert (ROA) system can be quickly diagnosed for problems with the KDS. (Refer to
"DTC guide")
| (1)
|
Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS.
(Refer to DTC guide when fault code is found.)
|
|
Refer to the KDS screen for operating conditions and details
|
|
ROA (Rear Occupant Alert) System Removal and Installation
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
| 1. |
Remove the roof trim assembly.
(Refer to Roof Trim - "Roof Trim Assembly")
|
| 2. |
Disconnect the rear occupant alert sensor (ROA) connector (A).
|
| 3. |
Remove the ROA (A).
|
Clip position :
|
|
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
| 1. |
Install in the reverse order of removal.
|
Side Body Control Unit On Vehicle Inspection
| 1. |
The side body control unit can be quickly diagnosed for problems with the KDS (Refer to "DTC
guide").
| (1)
|
Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS.
(Refer to DTC guide when fault code is found.)
|
| (2)
|
S/W Management : Controlling other features including system option setting and zero point
adjustment.
(S/W Management → Side Body zone Control Module_Driver → Variant Coding)
(S/W Management → Side Body zone Control Module_Assist → Variant Coding)
|
|
Refer to the KDS screen for operating conditions and details
|
|
Side Body Control Unit Removal and Installation
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedure.
|
|
Side Body Control Unit [Crash Pad Side]
| 1. |
Remove the ADAS parking ECU bracket.
(Refer to Advanced Driver Assistance System - "ADAS parking ECU
(ADAS_PRK)")
|
| 2. |
Remove the unit (A) after disconnect the connectors (B).
|
| 3. |
Remove the unit (A) after removing the nuts.
Tightening torque :
6.9 - 10.8 N·m (0.7 - 1.1 kgf·m, 5.1 - 8.0 lb·ft)
|
|
Side Body Control Unit [Floor Carpet Side]
| 1. |
Remove the luggage side trim.
(Refer to Luggage Trim - "Luggage Side Trim")
|
| 2. |
Separate the floor carpet (A).
|
| 3. |
Disconnect the unit connector (A).
|
| 4. |
Remove the unit (A) after removing the nuts.
Tightening torque :
6.9 - 10.8 N·m (0.7 - 1.1 kgf·m, 5.1 - 8.0 lb·ft)
|
|
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedure.
|
|
| 1. |
Install in the reverse order of removal.
|
| 2. |
Perform the order below with the KDS when replacing the side body control unit.
(S/W Management → Side Body zone Control Module_Driver → Variant Coding)
(S/W Management → Side Body zone Control Module_Assist → Variant Coding)
|
| 3. |
Perform Over The Air (OTA) controller S/W update with KDS.
(Refer to Security & Vehicle Ignition System - "Over The Air
(OTA)")
|
| 4. |
Drive the vehicle at a speed of 20 km/h or above when replacing the side body control unit to activate the
unit.
|
Smart Key System Specification
RF Receiver
Item
|
Specification
|
Frequency (MHz)
|
433.92
|
Antenna type
|
FSK
|
Smart Key
Item
|
Specification
|
Fob key
|
Battery
|
Lithium battery 3V 1 unit
|
Distance
|
- The distance over which Radio Frequency (RF) Receiver can receive a FOB transmission
signal : 30 m (98.4 ft.) - The distance over which LF(Low Frequency) antenna(Outer Handle/ Tailgate ) can
detect FOB : 0.7m
|
Battery life
|
More than 2 years (20 times / a day)
|
Push buttons
|
7 (Door lock / unlock, Trunk open, Panic, Remote start, Forward / Backward)
|
Frequency (MHz)
|
125
|
Frequency (KHz)
|
433.92
|
Numbers
|
3 units (Fob key 2 units, card key 1 unit)
|
|
An inappropriately disposed battery can be harmful to the environment and human health.
|
Antenna
Item
|
Specification
|
Rated voltage (V)
|
DC 12
|
Operating voltage (V)
|
DC 9 - 16
|
Operating temperature [°C (°F)]
|
-40 to 85 (-40 to 185)
|
Frequency (KHz)
|
125
|
Numbers
|
Interior (3 units), Door (2 units), Front Bumper Beam(1 unit, RSPA Only), Rear Bumper(1unit)
|
Smart Key System On Vehicle Inspection. Smart Key System Code Saving
Smart Key System On Vehicle Inspection
| 1. |
The smart key system can quickly diagnosed for problems with the KDS (Refer to "DTC guide").
| (1)
|
Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS.
(Refer to DTC guide when fault code is found.)
|
| (2)
|
S/W Management : Controlling other features including system option setting and zero point
adjustment.
(S/W Management → BDC-SMK → Neutralization Mode)
(S/W Management → BDC-SMK → SMK STATUS INFORMATION)
(S/W Management → BDC-SMK → FOB KEY STATUS INFORMATION)
(S/W Management → BDC-SMK → Smart Key Code Saving)
(S/W Management → BDC-SMK → Antenna Status Check)
|
|
Refer to the KDS screen for operating conditions and details
|
|
Smart Key System Code Saving
|
Refer to the KDS screen for operating conditions and details
|
Smart Key Code Saving
| 1. |
Select the "Smart Key Code Saving" on the menu with the KDS.
(S/W Management → BDC-SMK → Smart Key Code Saving)
|
Smart Key Status Check
| 1. |
Perform the "SMK STATUS INFORMATION" with the KDS.
(S/W Management → BDC-SMK → SMK STATUS INFORMATION)
|
Smart Key System Removal and Installation
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
Interior Antenna #1
| 1. |
Remove the front console cover.
(Refer to Floor Console - "Front Console Cover")
|
| 2. |
Disconnect the antenna connector (A).
|
| 3. |
Remove the antenna (A) after removing the screws.
|
Interior Antenna #2
| 1. |
Remove the floor console assembly.
(Refer to Floor Console - "Floor Console Assembly")
|
| 2. |
Remove the antenna.
| (1)
|
Disconnect the antenna connector (B).
|
| (2)
|
Remove the antenna (A) after removing the screws.
|
|
Interior Antenna #3
| 1. |
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage
service interlock connector.
| (1)
|
Open the front trunk (A).
|
| (2)
|
Open the auxiliary 12 V battery service cover (A).
|
| (3)
|
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).
Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)
|
|
| (4)
|
Disconnect the service interlock connector (A).
|
•
|
Wait more than 5 minutes for capacitor of the high voltage battery system to be
discharged completely.
|
|
•
|
When working on a vehicle during discharging the capacitor, it can cause an
electrical shock or injury, so follow the manual.
|
|
|
The service interlock connector cannot be completely removed.
|
|
|
| 2. |
Remove the rear transverse trim.
(Refer to Luggage Trim - "Rear Transverse Trim")
|
| 3. |
Disconnect the antenna connector (A).
|
| 4. |
Remove the antenna (A) after removing the nuts.
Tightening torque :
3.9 - 4.2 N·m (0.4 - 0.43 kgf·m, 2.9 - 3.1 lb·ft, 34.7 - 37.3 lb·in)
|
|
Rear Bumper Antenna
| 1. |
Remove the rear bumper assembly.
(Refer to Front & Rear Bumper - "Rear Bumper
Assembly")
|
| 2. |
Disconnect the antenna connector (A).
|
| 3. |
Remove the antenna (A) after removing the screws.
|
Front Bumper Beam Antenna
| 1. |
Remove the front bumper assembly.
(Refer to Front & Rear Bumper - "Front Bumper
Assembly")
|
| 2. |
Disconnect the antenna connector (A).
|
| 3. |
Remove the antenna (A) after removing the screws.
|
Front Door Antenna
| 1. |
Remove the front door trim.
(Refer to Front Door - "Front Door Trim")
|
| 2. |
Disconnect the antenna connector (A).
|
| 3. |
Remove the antenna (A) after removing the screws.
|
Buzzer
| 1. |
Remove the front bumper assembly.
(Refer to Front & Rear Bumper - "Front Bumper
Assembly")
|
| 2. |
Remove the buzzer (A) after disconnecting the connector (B).
|
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
| 1. |
Install in the reverse order of removal.
|
Other information:
Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Wiper Blades
When the windshield wipers no longer clean the windshield effectively, the wiper blades may be worn, hardened,
cracked, or damaged and should be replaced.
To prevent damage to the wiper mechanism, wiper arms, or related components, never move the wiper blades
manually.
The use of non-approved wiper blades on the Kia EV6 may lead to poor wiping performance, excessive noise, or
premature failure.
Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: How to turn off Smart function while operating
Press the Parking/View button () during either of the
following stages:
Checking available exit space.
Selecting the desired exit direction.
Shift the transmission into R (Reverse) during either of the following stages:
Checking available exit space.
Selecting the exit direction.