Kia EV6: Body (Interior / Exterior / Electrical) / Roof Trim

Contents:

Components and Components Location

Component and Component Location
Sunroof Type

Body (Interior / Exterior / Electrical) — Roof Trim / Components and Components Location / Component and Component Location illustration

1. Multi-Sensor Blanking Cover
2. Multi-Sensor Cover
3. Overhead Console Lamp
4. Sunvisor Retainer
5. Sunvisor
6. Assist handle
7. Room Lamp
8. Roof Trim Assembly
9. Roof Trim Harness

Non-Sunroof Type

Body (Interior / Exterior / Electrical) — Roof Trim / Components and Components Location / Component and Component Location illustration

1. Multi-Sensor Blanking Cover
2. Multi-Sensor Cover
3. Overhead Console Lamp
4. Sunvisor Retainer
5. Sunvisor
6. Assist handle
7. Room Lamp
8. Roof Trim Assembly
9. Roof Trim Harness

Assist Handle Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Remove the assist handle (A) after removing the screws.

Body (Interior / Exterior / Electrical) — Roof Trim / Assist Handle / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Multi Sensor Cover Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Remove the multi sensor blanking cover (A).

Body (Interior / Exterior / Electrical) — Roof Trim / Multi Sensor Cover / Removal and Installation / Removal illustration

2.
Remove the multi sensor cover (A) by pulling it in the direction of the arrow.

Body (Interior / Exterior / Electrical) — Roof Trim / Multi Sensor Cover / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Roof Trim Assembly Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Remove the front seat assembly.
(Refer to Front Seat - "Front Seat Assembly")
2.
Remove the front pillar trim.
(Refer to Interior Trim - "Front Pillar Trim")
3.
Remove the center pillar upper trim.
(Refer to Interior Trim - "Center Pillar Trim")
4.
Remove the rear pillar trim.
(Refer to Interior Trim - "Rear Pillar Trim")
5.
Remove the sun visor and retainer.
(Refer to Roof Trim - "Sunvisor")
6.
Remove the assist handle.
(Refer to Roof Trim - "Assist Handle")
7.
Remove the overhead console lamp.
(Refer to Light & Vision System - "Overhead Console Lamp")
8.
Remove the room lamp.
(Refer to Light & Vision System - "Room Lamp")
9.
Remove the vanity lamp.
(Refer to Light & Vision Systems - "Vanity Lamps")
10.
Remove the multi sensor cover.
(Refer to Roof Trim - "Multi Sensor Cover")
11.
Disconnect the connectors (A).

Body (Interior / Exterior / Electrical) — Roof Trim / Roof Trim Assembly / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Roof Trim / Roof Trim Assembly / Removal and Installation / Removal illustration

12.
Disconnect the roof trim wiring connector (A).

Body (Interior / Exterior / Electrical) — Roof Trim / Roof Trim Assembly / Removal and Installation / Removal illustration

13.
Disconnect the antenna extension connector (A).

Body (Interior / Exterior / Electrical) — Roof Trim / Roof Trim Assembly / Removal and Installation / Removal illustration

14.
Remove the roof trim assembly (A) after removing the fasteners.

Body (Interior / Exterior / Electrical) — Roof Trim / Roof Trim Assembly / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Roof Trim / Roof Trim Assembly / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Roof Trim / Roof Trim Assembly / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Sunvisor Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Remove the sunvisor (A) after removing the screw.

Body (Interior / Exterior / Electrical) — Roof Trim / Sunvisor / Removal and Installation / Removal illustration

2.
Remove the sunvisor retainer (A) after removing the screw.

Body (Interior / Exterior / Electrical) — Roof Trim / Sunvisor / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Other information:

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Gear position

The Kia EV6 instrument cluster displays the currently selected gear position whenever the EV button is in the DRIVE READY or POWER ON mode. P (Park) Always bring the Kia EV6 to a complete stop before shifting into P (Park). To shift from R (Reverse), N (Neutral), or D (Drive) into P (Park), press the [P] button. If the Kia EV6 is switched OFF while stationary, the transmission system automatically shifts into P (Park).

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Active air flap

The active air flap system in the Kia EV6 automatically controls the airflow openings located beneath the front bumper in order to cool key vehicle components and improve aerodynamic efficiency and electric driving range. By adjusting airflow dynamically according to driving conditions, battery temperature, and cooling requirements, the Kia EV6 active air flap system helps optimize overall energy efficiency and thermal management.

Contents

Categories

 
Copyright © 2026 Kia EV6 Manuals � 0.015