Kia EV6: Steering System / Steering Column Module (SCM)
Contents:
Components and Components Location. Specification
Components and Components Location
1. Steering Column Module (SCM) 1-a. 3.9 - 4.2 N·m
(0.4 - 0.43 kgf·m, 2.9 - 3.1 lb·ft, 34.7 - 37.3 lb·in)
|
|
Specification
Steering Column Module (SCM)
Item
|
Specification
|
Rated voltage (V)
|
12
|
Operation voltage (V)
|
9 - 16
|
Operating temperature [°C (°F)]
|
-30 to 75 (-22 to 167)
|
Storage temperature (°C [°F])
|
-40 to 85 (-40 to 185)
|
Parasitic Current (mA)
|
Maximum 0.7
|
Description and Operation
The Steering Column Module (SCM) stores the optimal steering column position set by the driver in the tilt and
telescope unit by IMS switch operation and can play it back to the position set by the driver with the IMS switch even
if the position of the steering column changes.
For safety, it has a function of prohibiting operations while driving and urgently stopping operations depending on
the situation.
| 1. |
Manual Operating
|
•
|
Tilt and telescopic control by operating the manual switch.
|
|
•
|
When the manual switch signal is input, the relay is activated to change the steering column
position.
|
|
| 2. |
Memory
|
•
|
It memorizes and operates the tilt and telescopic positions of 2 drivers.
|
|
•
|
When the driver operates the IMS switch, the stored steering column position is received from the
Body Domain Control (BDC) unit via CAN data to operate.
|
|
•
|
Operation by CAN data received when IMS switch input signal.
|
|
| 3. |
Door open/close operation : It is the operating function according to driver door OPEN/CLOSE (received CAN
data from BDC )
|
Removal and Installation
|
•
|
When working on high voltage system, the work should be performed by technicians who have completed
the relevant training. A lack of understanding of the high voltage system can lead to serious
accidents due to electric shock or electric leakage.
|
|
•
|
When working on high voltage system or related components, make sure that you are familiar and
comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the
instructions, serious accidents due to electric shock or leakage may occur.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedures.
|
|
Steering Column Module (SCM)
| 1. |
Disconnect the battery negative ( - ) terminal and the service interlock connector.
(Refer to Battery Control System - "Auxiliary 12 V Battery -
2WD")
(Refer to Battery Control System - "Auxiliary 12 V Battery -
4WD")
|
| 2. |
Remove the glove box housing.
(Refer to Body - "Glove Box")
|
| 3. |
Disconnect the steering column module connector (A) and wiring clip (B).

|
| 4. |
Remove the steering column module after removing the nuts (A).
Tightening torque :
3.9 - 4.2 N·m (0.4 - 0.43 kgf·m, 2.9 - 3.1 lb·ft, 34.7 - 37.3 lb·in)
|

|
Steering Column Module (SCM) Switch
| 1. |
Remove the steering column lower shroud panel.
(Refer to Body - "Steering Column Shroud Panel")
|
| 2. |
Separate the steering column module switch connector clip (A).

|
| 3. |
Remove the steering column module switch (B) pushing in direction of the arrow while pressing the hinges
(A).



|
|
•
|
When working on high voltage system, the work should be performed by technicians who have completed
the relevant training. A lack of understanding of the high voltage system can lead to serious
accidents due to electric shock or electric leakage.
|
|
•
|
When working on high voltage system or related components, make sure that you are familiar and
comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the
instructions, serious accidents due to electric shock or leakage may occur.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedures.
|
|
Steering Column Module (SCM)
| 1. |
Install in the reverse order of removal.
|
Install to the specified torque.
|
|
| 2. |
Perform the order below with the KDS.
(S/W Management → SCM - Steering Column Module → Steering Limit Position Setting)
|
Refer to the KDS screen for operating conditions and details
|
|
| 3. |
Perform Over The Air (OTA) controller S/W update with KDS.
(Refer to Body - "Over The Air (OTA)")
|
Steering Column Module (SCM) Switch
| 1. |
Install in the reverse order of removal.
|
•
|
Install to the specified torque.
|
|
•
|
Match the grooves of the switch (A) and the lower shroud panel (B) when installing.
|
|
|
Other information:
Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: A Guide to Storage, Transport and Disposal of Old Battery Systems
Used high voltage battery system storage, transportation, disposal
guide
•
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training.
Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Limitations of Smart Cruise Control
Under the following conditions, Smart Cruise Control on the Kia EV6 may operate abnormally, react later than
expected, or function differently from normal operation. Drivers should always remain alert and avoid relying
entirely on automated assistance systems.
The detection sensor or surrounding sensor area is contaminated, obstructed, damaged, or covered with
dirt,
snow, water, ice, or road debris.