Kia EV6: Steering System / Steering Wheel

Contents:

Components and Components Location

Component
Standard

Steering System — Steering Wheel / Components and Components Location / Component illustration

1. Driver Air Bag (DAB) Module
2. Steering Wheel Bezel
3. Haptic Motor
4. Hands on Detection (HoD) Controller
5. Steering Wheel Body
5-a. 39.3 - 49.0 N·m (4.0 - 5.0 kgf·m, 29.0 - 36.1 lb·ft)
6. Dynamic Damper
7. Paddle Shift Switch
8. Steering Wheel Extension Wire
9. Steering Wheel Lower Cover

GT-line

Steering System — Steering Wheel / Components and Components Location / Component illustration

1. Driver Airbag (DAB)
2. Steering Wheel Bezel
3. Drive Mode Switch
4. Steering Wheel Remote Control (SWRC) Switch
5. Horn Plate
6. Steering Wheel Body
6-a. 39.3 - 49.0 N·m (4.0 - 5.0 kgf·m, 29.0 - 36.1 lb·ft)
7. Hands on Detection (HoD) Controller
8. Haptic Motor
9. Paddle Shifter Switch
10. Steering Wheel Extension Wire
11. Steering Wheel Lower Cover

Removal and Installation

Removal
Warning
•
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
•
When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
Standard
1.
Align the steering wheel straight.
2.
Disconnect the battery negative ( - ) terminal and the service interlock connector.
(Refer to Battery Control System - "Auxiliary 12 V Battery - 2WD")
(Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
3.
Secure the steering wheel to prevent movement.
4.
Remove the driver airbag module.
(Refer to Restraint - "Driver Airbag (DAB)")
5.
Disconnect the steering wheel connector (A).

Steering System — Steering Wheel / Removal and Installation / Removal illustration

6.
Remove the steering wheel (A) after removing the bolt.

Tightening torque :
39.3 - 49.0 N·m (4.0 - 5.0 kgf·m, 29.0 - 36.1 lb·ft)

Steering System — Steering Wheel / Removal and Installation / Removal illustration

Note
•
Do not use a hammer when removing steering wheel, the steering column may be damaged if using a hammer.
•
Do not reuse the steering wheel bolt.
GT-line
1.
Align the steering wheel straight.
2.
Disconnect the battery negative ( - ) terminal and the service interlock connector.
(Refer to Battery Control System - "Auxiliary 12 V Battery - 2WD")
(Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
3.
Secure the steering wheel to prevent movement.
4.
Remove the driver airbag module.
(Refer to Restraint - "Driver Airbag (DAB)")
5.
Disconnect the steering wheel connector (A).

Steering System — Steering Wheel / Removal and Installation / Removal illustration

6.
Remove the steering wheel (A) after removing the bolt.

Tightening torque :
39.3 - 49.0 N·m (4.0 - 5.0 kgf·m, 29.0 - 36.1 lb·ft)

Steering System — Steering Wheel / Removal and Installation / Removal illustration

Note
•
Do not use a hammer when removing steering wheel, the steering column may be damaged if using a hammer.
•
Do not reuse the steering wheel bolt.
Installation
Warning
•
When working on high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or electric leakage.
•
When working on high voltage system or related components, make sure that you are familiar and comply with the "Safety Precautions, Cautions and Warnings." If you do not comply with the instructions, serious accidents due to electric shock or leakage may occur.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedures.
1.
Install in the reverse order of removal.
Note
•
Install to the specified torque.
•
Do not reuse the steering wheel bolt.
•
Match the 3 marks when installing. (For a new one, mark 3 points same as the old one.)

Steering System — Steering Wheel / Removal and Installation / Installation illustration

Disassembly and Reassembly

Disassembly
Standard
1.
Remove the paddle shift switch mounting screws (A).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

2.
Separate the paddle shifter switch (A) with a suitable tool.

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

3.
Disconnect the paddle shift connectors (B), and then remove the paddle shift switches (A).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

4.
Remove the steering wheel lower cover (A) after removing the screws.

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

5.
Disconnect the remote control switch connectors (A).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

6.
Disconnect the heated steering wheel connector (A).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

7.
Remove the extension wiring ground screw (A).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

8.
Remove the steering wheel dynamic damper (A) after removing the screws.

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

9.
Disconnect the Hands on Detection (HoD) controller connector (A).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

10.
Disconnect the haptic motor connector (A).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

11.
Remove the steering wheel extension wiring (A).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

12.
Remove the Steering Wheel Remote Control (SWRC) switch and bezel screws (A).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

13.
Remove the steering wheel remote control (SWRC) switch and bezel (A).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

14.
Remove the haptic motor (A) after removing the screws.

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

15.
Remove the steering wheel remote control (SWRC) switch screws (A).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

16.
Remove the steering wheel remote control (SWRC) switches (A).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

GT-line
1.
Remove the paddle shift switch mounting screws (A).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

2.
Separate the paddle shifter switches (A).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

3.
Remove the paddle shift switches (A) after disconnecting the paddle shift connectors (B).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

4.
Remove the horn plate screws (A).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

5.
Disconnect the horn connector (A), and then remove the horn plate (B).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

6.
Remove the steering wheel lower cover (A) after removing the screws.

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

7.
Disconnect the haptic motor connector (A).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

8.
Remove the haptic motor (A) after removing the screws.

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

9.
Disconnect the remote control switch connectors (A).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

10.
Disconnect the heated steering wheel connector (A).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

11.
Separate the hands on detection (HoD) controller (A).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

12.
Disconnect the hands on detection (HoD) controller connector (A).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

13.
Remove the hand on detection (HoD) controller after disconnecting the connector (A).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

14.
Remove the extension wiring ground screw (A).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

15.
Disconnect the drive mode switch connector (A).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

16.
Remove the steering wheel extension wiring (A).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

17.
Remove the steering wheel remote control (SWRC) switch and bezel screws (A).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

18.
Remove the steering wheel remote control (SWRC) switch and bezel (A).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

19.
Remove the steering wheel remote control (SWRC) switch screws (A).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

20.
Remove the steering wheel remote control (SWRC) switches (A).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

21.
Remove the drive mode switch screws (A).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

22.
Remove the drive mode switch (A).

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

23.
Remove the steering wheel bezel (A) after removing the screws.

Steering System — Steering Wheel / Disassembly and Reassembly / Disassembly illustration

Reassembly
1.
Reassemble in the reverse order of disassembly.
Note
•
When assembling the steering wheel, be careful not to damage the parts by tightening with excessive torque.
•
Disconnection or short circuit may occur if the main wiring is not held in place when mounting the steering wheel lower cover.
2.
Perform Over The Air (OTA) controller S/W update with KDS if the HoD controller is replaced with a new one.
(Refer to Body - "Over The Air (OTA)")

Heated steering wheel Components and Components Location. Heated steering wheel Removal and Installation

Heated steering wheel Components and Components Location

Component

Steering System — Steering Wheel / Heated steering wheel / Components and Components Location / Component illustration

1. Heated Steering Wheel Control Unit (Integrated with Powernet Domain Controller)
2. Heated steering Wheel Control Switch (Integrated with Floor Console Switch)

Heated steering wheel Removal and Installation

Removal
Heated Steering Wheel Control Unit
Note
The heated steering control unit is integrated with the powernet domain controller (PDC), so replace the PDC.
1.
Remove the powernet domain controller.
(Refer to Body - "Junction Block")
Heated Steering Switch
Note
The heated steering switch is integrated with the floor console switch, so replace the floor console switch.
1.
Remove the floor console switch.
(Refer to Body - "Floor Console Switch")
Installation
1.
Install in the reverse order of removal.

Paddle Shifter Switch Removal and Installation

Removal
Warning
•
When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shocks or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Remove the driver airbag module.
(Refer to Restraint - "Driver Airbag (DAB)")
Caution
If the airbag is deployed, there may be a risk of injury, so always store the detached airbag module with the cover facing upwards.
2.
Remove the paddle shift switch mounting screws (A).
[LH]

Steering System — Steering Wheel / Paddle Shifter Switch / Removal and Installation / Removal illustration

[RH]

Steering System — Steering Wheel / Paddle Shifter Switch / Removal and Installation / Removal illustration

3.
Separate the paddle shifter switch (A) with a suitable tool.
[LH]

Steering System — Steering Wheel / Paddle Shifter Switch / Removal and Installation / Removal illustration

[RH]

Steering System — Steering Wheel / Paddle Shifter Switch / Removal and Installation / Removal illustration

4.
Disconnect the paddle shifter switch connector (B) then remove the paddle shifter switch (A).
[LH]

Steering System — Steering Wheel / Paddle Shifter Switch / Removal and Installation / Removal illustration

[RH]

Steering System — Steering Wheel / Paddle Shifter Switch / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the repairs should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shocks or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shocks or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.
Note
Install to the specified torque.

Other information:

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Precautions for accident vehicle

Precautions for accident vehicle Electric vehicle includes a high voltage battery, which can lead to serious accidents such as short circuits or electric shocks if touched incorrectly.

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Rain Sensor Removal and Installation

Removal • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training.

Contents

Categories

 
Copyright © 2026 Kia EV6 Manuals ⏱ 0.0161