Kia EV6: Steering System

Contents:

Single-Use Parts

Single-Use Parts
Non-reusable parts (Single-Use Parts)
Workshop manual provides “Components and Components Location� which can be used to identify “Non-reusable parts�. When repairing a vehicle, Non-reusable parts such as fasteners, gaskets, washers, clips and garnishes must be replaced. Kia Non-reusable parts are designed to be installed only once.
Before working on a vehicle, check “Components and Components Location� to find the non-reusable parts in a system.
※ Symbol of Non-reusable parts
Symbol
Meaning

Steering System — Single-Use Parts illustration

Do not reuse the part. Replace with a new one.

※ Example of “Components and Components Location�

Steering System — Single-Use Parts illustration

High Voltage System General Safety Information and Caution ➤

High Voltage Shut-off Procedures

High Voltage Shut-off Procedures

High Voltage Shut-off Procedures
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Information
High Voltage Component : Battery System Assembly (BSA), motor assembly, inverter assembly, high voltage junction box, power cable, etc.
1.
Check the Battery Management Unit (BMU) weld flag with the KDS.
(Data Analysis → Battery Management System (BMS) → BMU Weld Flag)

Specified value : NO

Information
Refer to the KDS screen for operating conditions and details.
2.
Open the front trunk (A).

Steering System — High Voltage Shut-off Procedures illustration

3.
Open the low voltage (12 V) battery service cover (A).

Steering System — High Voltage Shut-off Procedures illustration

4.
Turn the POWER OFF, separate the low voltage (12 V) battery ( - ) terminal (A).

Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)

Steering System — High Voltage Shut-off Procedures illustration

5.
Disconnect the service interlock connector (A).

Steering System — High Voltage Shut-off Procedures illustration

Warning
•
Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
•
When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
Note
The service interlock connector cannot be completely removed.

Steering System — High Voltage Shut-off Procedures illustration

6.
Remove the front under cover.
(Refer to Motor and Reduction Gear System - "Front Under Cover")
7.
Remove the high voltage battery cover (A).

Tightening torque :
7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)

Steering System — High Voltage Shut-off Procedures illustration

8.
Disconnect the front high voltage junction box power cable (A).

Steering System — High Voltage Shut-off Procedures illustration

Note
How to disconnect the connector
1)
Release the locking clip (A) by pulling it.
2)
Disconnect the connector by pushing the lever (A) in the direction of the arrow while pressing the locking clip (B).

Steering System — High Voltage Shut-off Procedures illustration

9.
Remove the center floor rear under cover.
(Refer to Motor and Reduction Gear System - "Rear Under Cover")
10.
Disconnect the Integrated Charge Control Unit (ICCU) connector (A).

Steering System — High Voltage Shut-off Procedures illustration

Note
How to disconnect the connector
1)
Release the locking clip (A) by pulling it.
2)
Disconnect the connector while pressing the locking clip (B).

Steering System — High Voltage Shut-off Procedures illustration

11.
Disconnect the rear high voltage junction box power cable (A).

Steering System — High Voltage Shut-off Procedures illustration

Note
How to disconnect the connector
1)
Release the locking clip (A) by pulling it.
2)
Disconnect the connector by pushing the lever (A) in the direction of the arrow while pressing the locking clip (B).

Steering System — High Voltage Shut-off Procedures illustration

12.
Measure the voltage between the high voltage power connector and high voltage battery terminal to check whether the high voltage is shut-off.

30 V or less : Normal cut off high voltage circuit
Above 30 V : Fault on high voltage circuit

(1)
Measure the voltage between the high voltage power connector positive ( + ) terminal and negative ( - ) terminal.

Steering System — High Voltage Shut-off Procedures illustration

(2)
Measure the voltage between the high voltage battery positive ( + ) and negative ( - ) terminal.

Steering System — High Voltage Shut-off Procedures illustration

(3)
Measure the voltage between the high voltage battery positive ( + ) terminal and ground.

Steering System — High Voltage Shut-off Procedures illustration

(4)
Measure the voltage between the high voltage battery negative ( - ) terminal and ground.

Steering System — High Voltage Shut-off Procedures illustration

(5)
Measure the voltage between the rear high voltage battery positive ( + ) and negative ( - ) terminal.

Steering System — High Voltage Shut-off Procedures illustration

(6)
Measure the voltage between the rear high voltage battery positive ( + ) terminal and ground.

Steering System — High Voltage Shut-off Procedures illustration

(7)
Measure the voltage between the rear high voltage battery negative ( - ) terminal and ground.

Steering System — High Voltage Shut-off Procedures illustration

Warning
1)
Check for insulation breakdown via KDS and physical leakage current before working on EV.
2)
Remove the main fuse if insulation breakdown or leakage current is suspected. (Remove the main fuse even when DTC CODE ON such as PRA malfunction)
(Refer to High Voltage Battery Control System - "Main Fuse")
※ If there is no insulation breakdown or leakage current and it is normal, work without removing the main fuse.

Specification ➤

Special Service Tool

Special Service Tool
Tool Name / Number
Illustration
Description
Ball joint puller
09568 - 2J100

Steering System — Special Service Tool illustration

Used for removal of tie rod end
Lower arm ball joint remover
0K545 - A9100

Steering System — Special Service Tool illustration

Used for removal of front lower arm ball joint

Troubleshooting

Troubleshooting
Excessive play in steering
Suspected Cause
Remedy
Universal joint bolt got loose
Retighten or replace if necessary
Yoke plug got loose
Retighten
Steering gear box bolt got loose
Retighten
Tie rod end stud got loose or worn
Retighten or replace if necessary

Steering wheel does not return to its original position
Suspected Cause
Remedy
Excessive turning resistance of tie rod end
Replacement
Yoke plug excessively tight
Adjustment
Faulty tie rod or ball joint
Replacement
Steering gear box and front sub frame got loose
Retighten
Steering column shaft or body grommet got worn
Repair or replace
Bended rack
Replacement

Rattling or chucking noise in the rack and pinion
Suspected Cause
Remedy
Steering gear mounting bolts got loose
Retighten
Tie rod end ball joint got loose
Retighten
Tie rod or tie rod end ball joint got worn
Replacement
Yoke plug got loose
Retighten

Inspection

Inspection
Steering Wheel Play Inspection
1.
Align the steering wheel straight.
2.
Mark the steering wheel center (A) using masking tape or etc.

Steering System — Inspection illustration

3.
Turn the steering wheel until the wheel is moved while MDPS power is 'ON', then measure the distance the steering wheel has rotated.

Standard value :
0 - 30 mm (0 - 1.1811 in.) or less

Steering System — Inspection illustration

4.
If the steering wheel play exceeds standard value, inspect the steering column, shaft, and linkages.
Checking Stationary Steering Effort
1.
Place the vehicle on the level surface.
2.
Measure the power when the steering wheel starts to move using a spring scale while MDPS power is 'ON'.

Standard value :
29.4 N (3.0 kgf, 6.6 lb·ft) MAX.

Steering System — Inspection illustration

3.
If the measured value exceeds standard value, inspect the steering gear box or MDPS system.

Steering Column Module (SCM) ➤

Steering Wheel ➤

Motor Driven Power Steering (MDPS) ➤

Other information:

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Refrigerant Recovery/Recycling/Charging/Vacuum/Leak Test

Refrigerant Recovery/Recycling/Charging/Vacuum/Leak Test (R-134a) Install the refrigerant recovery/recycling/charging equipment 1. Connect the refrigerant recovery/recycling/charging equipment to the high-pressure service port (A) and low-pressure service port (B). Refrigerant charging equipment should be installed on a flat surface so that it is easy to recover the refrigerant and in particular, the refrigerant can be accurately injected.

Contents

Categories

 
Copyright © 2026 Kia EV6 Manuals � 0.0156