Kia EV6: Body (Interior / Exterior / Electrical) / Crash Pad
Contents:
Components and Components Location
| Component and Component Location |
Crash Pad [Top]
1. Center Speaker Grille 2. Side Speaker Grille 3.
Rear Display Cover
|
4. Integrated monitor 5. Head up Display Cover 6.
Crash Pad Upper Panel
|
Crash Pad [Driver's Side]
1. Crash Pad Side Cover [Driver's side] 2. Crash
Pad Lower Panel 3. Crash Pad Switch
|
4. Steering Column Shroud Lower Panel 5. Crash Pad
Air Vent [Driver's side]
|
Crash Pad [Passenger Side]
1. Crash Pad Side Cover [Passenger's Side] 2.
Crash Pad Center Garnish [RH] 3. Infotainment Keyboard
|
4. Crash Pad Air Vent [Center] 5. Glove box
housing
|
Crash Pad [Center]
1. Steering column shroud upper panel 2. Crash Pad
Center Garnish
|
3. Crash pad center panel
|
Crash Pad Assembly
1. Knee Airbag (KAB) Module 1-a. 3.9 - 5.9 N·m (0.4 -
0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in) 2. Crash Pad Assembly 2-a. 17.7 - 23.5 N·m (1.8 - 2.4
kgf·m, 13.0 - 17.4 lb·ft)
|
3. Passenger Airbag (PAB) Module 3-a. 3.9 - 5.9 N·m
(0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in) 4. Crash Pad Air Vent Duct Assembly
|
Cowl Cross Bar
1. Cowl cross bar 1-a. 22.6 - 30.4 N·m (2.3 - 3.1
kgf·m, 16.6 - 22.4 lb·ft) 1-b. 16.7 - 23.5 N·m (1.7 - 2.4 kgf·m, 12.3 - 17.4 lb·ft)
|
1-c. 16.7 - 23.5 N·m (1.7 - 2.4 kgf·m, 12.3 - 17.4
lb·ft) 1-d. 16.7 - 23.5 N·m (1.7 - 2.4 kgf·m, 12.3 - 17.4 lb·ft) 1-e. 22.6 - 30.4 N·m (2.3 - 3.1 kgf·m,
16.6 - 22.4 lb·ft)
|
Cowl Cross Bar Assembly Removal and Installation
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
| 1. |
Remove the floor carpet assembly.
(Refer to Interior Trim - "Floor Carpet Assembly")
|
| 2. |
Remove the crash pad assembly.
(Refer to Crash Pad - "Crash Pad Assembly")
|
| 3. |
Lower the steering column after removing the nuts and through-bolt.
Refer to Steering System - "MDPS Column and Housing")
|
| 4. |
Remove the wiper motor.
(Refer to Exterior Green House - "Wiper Motor")
|
| 5. |
Remove the front console cover.
(Refer to Floor Console - "Front Console Cover")
|
| 6. |
Remove the bolts (A).
Tightening torque :
22.6 - 30.4 N·m (2.3 - 3.1 kgf·m, 16.6 - 22.4 lb·ft)
|
[Driver's Side]
[Passenger's Side]
[Brake Booster's Side]
|
| 7. |
Disconnect the airbag control unit (ACU) connector (A).
|
| 8. |
Disconnecting the roof trim wiring connector (A).
|
| 9. |
Disconnect the antenna extension connector (A).
|
| 10. |
Disconnect the powernet domain controller connectors (A).
|
| 11. |
Disconnect the multi box connectors (A).
[Driver's Side]
[Passenger's Side]
|
| 12. |
Disconnect the blower unit connector and remove the wiring clip.
[Driver's Side]
| (1)
|
Disconnect the temperature control actuator connector and mode control actuator connectors (A).
|
| (2)
|
Disconnect the evaporator temperature sensor connector (A) after removing the fastener.
|
Clip position :
|
|
| (3)
|
Disconnect the rear temperature control actuator connectors (A).
|
| (4)
|
Disconnect the interior antenna connector (A).
|
[Passenger's Side]
| (1)
|
Disconnect the auto defogging actuator, mode control actuator, temperature control actuator
connectors (A).
|
| (2)
|
Disconnect the PTC heater connector (A).
|
|
| 13. |
Disconnect the shower duct [LH] connector (A).
|
| 14. |
Remove the driver's side shower duct (A) after removing the screw.
|
| 15. |
Disconnect the passenger's side duct sensor connector (A).
|
| 16. |
Disconnect the PTC heater ground wire (A) after removing the bolt.
Tightening torque :
10.8 - 13.7 N·m (1.1 - 1.4 kgf·m, 8.0 - 10.1 lb·ft)
|
|
| 17. |
Remove the bolts and nuts (A).
Tightening torque :
16.7 - 23.5 N·m (1.7 - 2.4 kgf·m, 12.3 - 17.4 lb·ft)
|
[Front of cowl cross bar]
[Behind the cowl cross bar]
|
| 18. |
Remove the cowl cross bar assembly (A) after removing the bolts and nuts.
Tightening torque :
16.7 - 23.5 N·m (1.7 - 2.4 kgf·m, 12.3 - 17.4 lb·ft)
|
[Driver's Side]
[Passenger's Side]
|
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
| 1. |
Install in the reverse order of removal.
|
Crash Pad Air Vent Removal and Installation
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
Crash Pad Air Vent Duct [LH]
| 1. |
Remove the crash pad lower panel.
(Refer to Crash Pad - "Crash Pad Panel")
|
| 2. |
Remove the air vent duct (A) after removing the screw.
|
Clip position :
|
|
| 3. |
Disconnect the mood lamp connector (A).
|
Crash Pad Air Vent Duct [Center]
| 1. |
Remove the infotainment keyboard.
(Refer to Infotainment system - "Infotainment Keyboard")
|
| 2. |
Remove the air vent duct (A) after removing the screws.
|
| 3. |
Disconnect the hazard switch connector (A).
|
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
| 1. |
Install in the reverse order of removal.
|
Crash Pad Assembly Removal and Installation
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
| 1. |
Remove the integrated monitor.
(Refer to Infotainment System - "Integrated Monitor")
|
| 2. |
Remove the front pillar trim.
(Refer to Interior Trim - "Front Pillar Trim")
|
| 3. |
Remove the crash pad center panel.
(Refer to Crash Pad - "Crash Pad Panel")
|
| 4. |
Remove the Auto Temperature Control Unit.
(Refer to Heating, Ventilation and Air Conditioning- "Auto Temperature
Control Unit")
|
| 5. |
Remove the front center speaker and front midrange speaker.
(Refer to Infotainment System - "Speaker")
|
| 6. |
Remove the multi-function switch.
(Driver & Driving Assistance System - "Multifunciton
Switch")
|
| 7. |
Remove the particulate matter (PM) sensor.
|
| 8. |
Disconnect the duct sensor connector (A).
|
| 9. |
Remove the passenger airbag mounting bolts (A).
Tightening torque :
3.9 - 5.9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)
|
|
| 10. |
Disconnect the passenger's airbag connector (A).
|
| 11. |
Remove the main crash pad assembly (A) after removing the bolts and nuts.
Tightening torque :
17.7 - 23.5 N·m (1.8 - 2.4 kgf·m, 13.0 - 17.4 lb·ft)
|
[Driver's Side]
[Passenger's Side]
|
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
| 1. |
Install in the reverse order of removal.
|
Crash Pad Cover Removal and Installation
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedure.
|
|
Center Speaker Grille
| 1. |
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage
service interlock connector.
| (1)
|
Open the front trunk (A).
|
| (2)
|
Open the auxiliary 12 V battery service cover (A).
|
| (3)
|
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).
Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)
|
|
| (4)
|
Disconnect the service interlock connector (A).
|
•
|
Wait more than 5 minutes for capacitor of the high voltage battery system to be
discharged completely.
|
|
•
|
When working on a vehicle during discharging the capacitor, it can cause an
electrical shock or injury, so follow the manual.
|
|
|
The service interlock connector cannot be completely removed.
|
|
|
| 2. |
Remove the grille (A).
|
| 3. |
Disconnecting the photo sensor connector (A).
|
Side Speaker grille
| 1. |
Remove the grille (A).
|
Crash Pad Side Cover
| 1. |
Remove the front door body side weatherstrip.
(Refer to Front Door - "Front Door Weatherstrip")
|
| 2. |
Remove the cover (A).
|
Clip position :
|
|
Rear Display Cover
| 1. |
Remove the cover (A).
|
Clip position :
|
|
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedure.
|
|
| 1. |
Install in the reverse order of removal.
|
Crash Pad Garnish Removal and Installation
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedure.
|
|
Crash Pad Center Garnish
| 1. |
Remove the crash pad lower panel.
(Refer to Crash Pad - "Crash Pad Panel")
|
| 2. |
Remove the garnish (A).
|
Clip position :
|
|
Crash Pad Center Garnish [RH]
| 1. |
Remove the crash pad center garnish.
|
| 2. |
Separate the garnish (A) after removing the screws.
|
Clip position :
|
|
| 3. |
Remove the garnish (A) after disconnecting the in-car sensor connector (B).
|
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedure.
|
|
| 1. |
Install in the reverse order of removal.
|
Crash Pad Panel Removal and Installation
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedure.
|
|
Crash Pad Lower Panel
| 1. |
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage
service interlock connector.
| (1)
|
Open the front trunk (A).
|
| (2)
|
Open the auxiliary 12 V battery service cover (A).
|
| (3)
|
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).
Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)
|
|
| (4)
|
Disconnect the service interlock connector (A).
|
•
|
Wait more than 5 minutes for capacitor of the high voltage battery system to be
discharged completely.
|
|
•
|
When working on a vehicle during discharging the capacitor, it can cause an
electrical shock or injury, so follow the manual.
|
|
|
The service interlock connector cannot be completely removed.
|
|
|
| 2. |
Remove the crash pad side cover.
(Refer to Crash Pad - "Crash Pad Cover")
|
| 3. |
Remove the panel (A) after removing the screws.
|
Clip position :
|
|
| 4. |
Disconnect the crash pad switch connector (A).
|
| 5. |
Disconnect the diagnostic tool connector (A).
|
Crash Pad Center Panel
| 1. |
Remove the crash pad lower panel.
|
| 2. |
Remove the front console cover.
(Refer to Floor Console - "Front Console Cover")
|
| 3. |
Remove the glove box housing.
(Refer to Crash Pad - "Glove Box")
|
| 4. |
Remove the panel (A) after removing the screws.
|
Head Up Display Cover
| 1. |
Remove the center speaker grille.
(Refer to Crash Pad - "Crash Pad Cover")
|
| 2. |
Remove the cover (A).
|
Clip position :
|
|
Crash Pad Upper Panel
| 1. |
Remove the crash pad air vent duct.
(Refer to Crash Pad - "Crash Pad Air Vent")
|
| 2. |
Remove the panel (A) after removing the screws.
|
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedure.
|
|
| 1. |
Install in the reverse order of removal.
|
Crash Pad Switch Removal and Installation
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedure.
|
|
| 1. |
Remove the crash pad lower panel.
(Refer to Crash Pad - "Crash Pad Panel")
|
| 2. |
Remove the crash pad switch (A) after removing the screws.
|
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedure.
|
|
| 1. |
Install in the reverse order of removal.
|
Glove Box Removal and Installation
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
Glove Box
| 1. |
Open the glove box (A).
|
| 2. |
Separate the glove box air damper (A).
|
| 3. |
Remove the glove box retainer (A) by pulling it in the direction of the arrow.
|
| 4. |
Remove the glove box (A).
|
Glove Box Housing
| 1. |
Remove the center air vent duct assembly.
(Refer to Crash Pad - "Crash Pad Air Vent")
|
| 2. |
Remove the auto temperature control unit.
(Refer to Heating, Ventilation and Air Conditioning - "Auto
Temperature Control Unit")
|
| 3. |
Remove the glove box housing after removing the screws.
|
| 4. |
Remove the glove box housing (A) after disconnecting the glove box lamp connector (B).
|
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE)
and high voltage shut-off procedure.
|
|
| 1. |
Install in the reverse order of removal.
|
Steering Column Shroud Panel Removal and Installation
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedure.
|
|
| Steering Column Shroud Lower Panel |
| 1. |
Remove the crash pad lower panel.
(Refer to Crash Pad - "Crash Pad Panel")
|
| 2. |
Remove the steering wheel.
(Refer to Steering System - "Steering Wheel")
|
| 3. |
Separate the steering column shroud upper panel (A).
|
| 4. |
Remove the steering column shroud lower panel (A) after removing the screws.
|
| Steering Column Shroud Upper Panel |
| 1. |
Separate the steering column shroud upper panel (A).
|
| 2. |
Remove the steering column shroud upper panel (A) after disconnecting the in cabin cam connector (B).
|
Clip position :
|
|
|
•
|
When working on the high voltage system, the work should be performed by technicians who have
completed the relevant training. A lack of understanding of the high voltage system can lead to
serious accidents due to electric shock or short circuit.
|
|
•
|
When working on the high voltage system or related components, be sure to observe and be aware of
the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due
to electric shock or short circuit.
|
|
•
|
When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and
high voltage shut-off procedure.
|
|
| 1. |
Install in the reverse order of removal.
|
Other information:
Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Defogging logic: (if equipped)
The Kia EV6 automatic defogging logic helps reduce the possibility of windshield fogging by automatically
controlling
the air intake mode and air conditioning operation according to specific conditions, such as () or () mode.
To deactivate or restore the Kia EV6 automatic defogging logic, follow the procedure below.
Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: LCD display modes
View
Description
Driving Assist view
Displays information related to Kia EV6 driver assistance and safety systems.
Navigation view
Displays navigation guidance, route information, and map-related details.
Utility information view
Displays driving information, warnings, energy economy data, and additional vehicle status
information.

Contents
Categories