Kia EV6: Body (Interior / Exterior / Electrical) / Front Seat

Contents:

Components and Components Location. On Vehicle Inspection

Components and Components Location

Component

Body (Interior / Exterior / Electrical) — Front Seat / Components and Components Location / Component illustration

1. Front Seat Assembly
1-a. 44.1 - 58.8 N·m (4.5 - 6.0 kgf·m, 32.5 - 43.4 lb·ft)
2. Headrest
3. Seat Back Garnish
4. Headrest Guide
5. Back board
6. Outer Shield Cover
7. Power Seat Control Switch
8.Seat Back Cover
9. Seat Back Cushion
10. Seat Back Heater
11. Seat Back Frame
11-a 44.1 - 58.8 N·m (4.5 - 6.0 kgf·m, 32.5 - 43.4 lb·ft)
12. Seat Cushion Cover
13. Seat Cushion Pad
14. Seat Cushion Heater
15. Heater Unit
16. Blower Unit
17. Seat Cushion Frame
18. Front Side Airbag [Driver's Side]
19. Front Side Airbag [Passenger's Side]

On Vehicle Inspection

On Vehicle Inspection
Diagnostic with KDS
1.
The front seat can quickly diagnosed for problems with the KDS. (Refer to "DTC guide")
(1)
Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS.
(Refer to DTC guide when fault code is found.)
Information
Refer to the KDS screen for operating conditions and details

Front Seat Assembly Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Front Seat Assembly
Information
It can control the seat height by operating the seat cushion power switch (A) as shown below.
[Driver's Side]

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Assembly / Removal and Installation / Removal illustration

[Passenger's Side]

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Assembly / Removal and Installation / Removal illustration

1.
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
(1)
Open the front trunk (A).

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Assembly / Removal and Installation / Removal illustration

(2)
Open the auxiliary 12 V battery service cover (A).

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Assembly / Removal and Installation / Removal illustration

(3)
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).

Tightening torque :
7.8 - 9.8 N·m (0.8 - 1.0 kgf·m, 5.8 - 7.2 lb·ft)

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Assembly / Removal and Installation / Removal illustration

(4)
Disconnect the service interlock connector (A).

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Assembly / Removal and Installation / Removal illustration

Warning
•
Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
•
When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
Note
The service interlock connector cannot be completely removed.

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Assembly / Removal and Installation / Removal illustration

2.
Remove the seat assembly after removing the bolts (A).

Tightening torque :
44.1 - 58.8 N·m (4.5 - 6.0 kgf·m, 32.5 - 43.4 lb·ft)

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Assembly / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Assembly / Removal and Installation / Removal illustration

3.
Disconnect the front seat connectors (A).

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Assembly / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Assembly / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Assembly / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Front Seat Back Cover Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Front Seat Back Cover
1.
Remove the front seat back cover assembly.
(Refer to Front Seat - "Front Seat Back Cover Assembly")
2.
Remove the velcro tapes (A) and the hog ring clips (B).

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Back Cover / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Back Cover / Removal and Installation / Removal illustration

3.
Remove the front seat back cover (A) and front seat back pad (B).

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Back Cover / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Front Seat Back Cover Assembly Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Front Seat Back Cover Assembly
1.
Remove the front seat shield inner cover and outer cover.
(Refer to Front Seat - "Front Seat Shield Cover")
2.
Remove the headrest (A).

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Back Cover Assembly / Removal and Installation / Removal illustration

3.
Remove the headrest guides (A).

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Back Cover Assembly / Removal and Installation / Removal illustration

4.
Remove the front seat back upper cover cap (A).

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Back Cover Assembly / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Back Cover Assembly / Removal and Installation / Removal illustration

5.
Remove the front seat back garnish (A) after removing the screws.

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Back Cover Assembly / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Back Cover Assembly / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Back Cover Assembly / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Back Cover Assembly / Removal and Installation / Removal illustration

6.
Remove the front seat back board (A) in the direction of the arrow.

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Back Cover Assembly / Removal and Installation / Removal illustration

7.
Disconnect the front seat connector (A).

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Back Cover Assembly / Removal and Installation / Removal illustration

8.
Remove the seat back assembly after removing the bolts (A).

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Back Cover Assembly / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Back Cover Assembly / Removal and Installation / Removal illustration

9.
Separate the protector (A).

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Back Cover Assembly / Removal and Installation / Removal illustration

10.
Remove the front seat back cover assembly (A) from the front seat back frame (B).

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Back Cover Assembly / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Front Seat Cushion Cover Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Front Seat Cushion Cover
1.
Remove the front seat cushion cover assembly.
(Refer to Front Seat - "Front Seat Cushion Cover Assembly")
2.
Remove the velcro tapes (A) and the hog ring clips (B).

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Cushion Cover / Removal and Installation / Removal illustration

3.
Remove the front seat cushion cover (A) and front seat cushion pad (B).

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Cushion Cover / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.
2.
Perform the order below with the KDS when replacing the PODS unit.
(S/W Management → Occupant Detection System → Body Sensor Reset)
Note
After initializing the passenger classification sensor unit, delete the airbag control module and the passenger classification sensor unit fault code (DTC).

Front Seat Cushion Cover Assembly Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Front Seat Cushion Cover Assembly
1.
Remove the front seat shield inner cover and outer cover.
(Refer to Front Seat - "Front Seat Shield Cover")
2.
Disconnect the front seat connectors (A).

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Cushion Cover Assembly / Removal and Installation / Removal illustration

3.
Remove the seat back assembly after removing the bolts (A).

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Cushion Cover Assembly / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Cushion Cover Assembly / Removal and Installation / Removal illustration

4.
Separate the protector (A).
[Front]

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Cushion Cover Assembly / Removal and Installation / Removal illustration

[Rear]

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Cushion Cover Assembly / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Cushion Cover Assembly / Removal and Installation / Removal illustration

[Left]

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Cushion Cover Assembly / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Cushion Cover Assembly / Removal and Installation / Removal illustration

[Right]

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Cushion Cover Assembly / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Cushion Cover Assembly / Removal and Installation / Removal illustration

5.
Remove the front seat cushion inner cover (A).

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Cushion Cover Assembly / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Cushion Cover Assembly / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Cushion Cover Assembly / Removal and Installation / Removal illustration

6.
Remove the front seat cushion cover assembly (A) from the front seat cushion frame (B).

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Cushion Cover Assembly / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.
2.
Perform the order below with the KDS when replacing the PODS unit.
(S/W Management → Occupant Classification System → Zero Re-calibration of Occupant Classification Sensor)
Note
After initializing the PODS unit, erase DTC regarding the airbag control unit and the PODS unit.

Front Seat Frame Assembly Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Front Seat Back Frame
1.
Remove the Side Airbag (SAB) module.
(Refer to Restraint - "Side Airbag (SAB) Module")
Front Seat Cushion Frame
1.
Remove the front seat cushion cover assembly.
(Refer to Front Seat - "Front Seat Cushion Cover Assembly")

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Frame Assembly / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.
2.
Perform the order below with the KDS when replacing the PODS unit.
(S/W Management → Occupant Classification System → Zero Re-calibration of Occupant Classification Sensor)
Note
After readjusting the passenger classification sensor unit, delete the airbag control module and passenger classification sensor unit fault code(DTC).

Front Seat Shield Cover Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Outer Shield Cover
1.
Remove the front seat assembly.
(Refer to Front Seat - "Front Seat Assembly")
2.
Remove the cover (A) after removing the screw.

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Shield Cover / Removal and Installation / Removal illustration

3.
Disconnect the power seat control switch connector (A).

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Shield Cover / Removal and Installation / Removal illustration

Inner Shield Cover
1.
Remove the front seat assembly.
(Refer to Front Seat - "Front Seat Assembly")
2.
Remove the cover (A) after removing the screws.

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Shield Cover / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Shield Cover / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Shield Cover / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Front Seat Switch Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Power Seat Control Switch
1.
Remove the front seat outer shield cover.
(Refer to Front Seat - "Front Seat Shield Cover")
2.
Remove the switch (A) after removing the screws.

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Switch / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Switch / Removal and Installation / Removal illustration

Integrated Memory Seat (IMS) Switch
1.
Remove the front driver door trim.
(Refer to Front Door - "Front Door Trim")
2.
Remove the switch (A) after removing the screws.

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Switch / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Front Seat Unit Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Integrated Memory Seat (IMS) Unit
1.
Remove the driver's side front seat assembly.
(Refer to Front Seat - "Front Seat Assembly")
2.
Disconnect the unit connectors (A).

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Unit / Removal and Installation / Removal illustration

3.
Remove the unit (A) after removing the screws.

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Unit / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Unit / Removal and Installation / Removal illustration

Blower Unit
1.
Remove the front seat assembly.
(Refer to Front Seat - "Front Seat Assembly")
2.
Disconnect the unit connector (A).

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Unit / Removal and Installation / Removal illustration

3.
Separate the clamp (A).

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Unit / Removal and Installation / Removal illustration

4.
Remove the unit (A).

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Unit / Removal and Installation / Removal illustration

Heater / Ventilation Unit
1.
Remove the passenger's side front seat assembly.
(Refer to Front Seat - "Front Seat Assembly")
2.
Disconnect the unit connector (A).

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Unit / Removal and Installation / Removal illustration

3.
Remove the unit (A) after removing the screws.

Body (Interior / Exterior / Electrical) — Front Seat / Front Seat Unit / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.
2.
When replacing the seat unit, perform Over The Air (OTA) controller S/W update with KDS.
(Refer to Security & Vehicle Ignition System - "Over The Air (OTA)")

Lumbar Support Removal and Installation

Removal
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Remove the front seat back cover assembly.
(Refer to Front Seat - "Front Seat Back Cover Assembly")
2.
Remove the lumbar support (B) after removing the fasteners (A).

Body (Interior / Exterior / Electrical) — Front Seat / Lumbar Support / Removal and Installation / Removal illustration

Body (Interior / Exterior / Electrical) — Front Seat / Lumbar Support / Removal and Installation / Removal illustration

Information
Clip position :

Body (Interior / Exterior / Electrical) — Front Seat / Lumbar Support / Removal and Installation / Removal illustration

3.
Disconnect the lumbar support connector (A).

Body (Interior / Exterior / Electrical) — Front Seat / Lumbar Support / Removal and Installation / Removal illustration

Installation
Warning
•
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
•
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
•
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
1.
Install in the reverse order of removal.

Other information:

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: General Safety Information and Caution

Precaution (R-134a) When Handling Refrigerant 1. R-134a liquid refrigerant is highly volatile. A drop on the skin of your hand could result in localized frostbite. When handling the refrigerant, be sure to wear gloves. 2. It is standard practice to wear goggles or glasses to protect your eyes, and gloves to protect your hands.

Kia EV6 (CV/CV1A) 2022-2026 Workshop Manual: Brake bleeding

Special Service Tool Tool Name / Number Illustration Description Air bleeding tool0K580 - 3D100 Used for brake bleeding (regulating pressure)(Used with 0K585 - E8100) Air bleeding tool adaptor0K585 - E8100 Used for brake bleeding (reservoir cap adapter)(Used with 0K580 - 3D100) Integrated Electronic Brake (IEB) System Air Bleeding procedures • Do not reuse the drained brake fluid.

 
Copyright © 2026 Kia EV6 Manuals ⏱ 0.0187